Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 11 |
Anti-lock braking system warning lamp indicates an ABS fault | 8 |
Horn not working (7.7 (a)) | 8 |
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 7 |
Brake hose excessively deteriorated | 7 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 6 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 5 |
Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
Registration plate lamp issues | 5 |
Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 5 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 4 |
Headlamp aim out of alignment | 4 |
Offside Side repeater incorrect colour (4.4.3 (a)) | 4 |
Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 3 |
Windscreen washer not working | 3 |
Registration plate issues | 3 |
Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
Offside Rear Shock absorbers has a serious fluid leak | 3 |
Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 3 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
Oil leaking excessively from engine (8.4.1 (a) (i)) | 2 |
Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 2 |
Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 2 |
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 2 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 2 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
Brakes imbalanced across an axle | 2 |
Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 2 |
Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 2 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sills (7.1.1 (a) (i)) | 1 |
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
Exhaust has a major leak of exhaust gases AT CENTRE CLAMP AND REAR BOX (6.1.2 (a)) | 1 |
Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Emissions not tested due to no emmision control fitted lamba wiring bare and touching body of vehicle both lamba sensors missing and insecure. (8.2.1.2 (d)) | 1 |
Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition (8.1.1 (a)) | 1 |
Exhaust has a major leak of exhaust gases manifold (6.1.2 (a)) | 1 |
Central Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Offside Rear Brake cable damaged (1.1.15 (a)) | 1 |
Offside Suspension component mounting prescribed area excessively damaged significantly reducing structural strength outer sills (5.3.6 (a) (i)) | 1 |
Nearside Suspension component mounting prescribed area excessively damaged significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
Nearside Front Anti-roll bar linkage damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both sills (5.3.6 (a) (i)) | 1 |
Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Rear Prop shaft securing bolt loose (6.1.7 (a) (i)) | 1 |
Braking system leaking One way valve at brake servo (1.1.3 (d)) | 1 |
Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength Rear of inner wheelarch/ inner sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength Rear of inner wheelarch/ inner sill (5.3.6 (a) (i)) | 1 |
Central Rear Seat belt missing (7.1.2 (a)) | 1 |
Offside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Nearside Front Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
Power steering component leaking (2.1.5 (a)) | 1 |
Oil leaking excessively from engine sump (8.4.1 (a) (i)) | 1 |
Exhaust silencer likely to become detached (8.1.1 (b) (ii)) | 1 |
Exhaust silencer insecure (8.1.1 (b) (i)) | 1 |
Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt split. (2.1.3 (g) (ii)) | 1 |
Power steering malfunctioning steering rack stiff when lock to lock test done. (2.1.5 (a)) | 1 |
Exhaust has a major leak of exhaust gases centre near cat (6.1.2 (a)) | 1 |
Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill backing (5.3.6 (a) (i)) | 1 |
Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill backing (5.3.6 (a) (i)) | 1 |
Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i)) | 1 |
Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i)) | 1 |
Offside Rear Brake hose leaking on an air braking system (1.1.12 (c) (i)) | 1 |
Offside Front Lower Suspension arm pin or bush excessively worn Tie bar bush worn (5.3.4 (a) (i)) | 1 |
Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill. (5.3.6 (a) (i)) | 1 |
Central Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Upper Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
Offside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Nearside Front Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Nearside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting corroded holes within 30cm of trail arm mounting (6.2.2 (d) (i)) | 1 |
Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting corroded/holes within 30cm of suspension mounting (6.2.2 (d) (i)) | 1 |
Emissions not tested not tested due to exhaust leak (8.2.1.2 (d)) | 1 |
Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower arm mounting (5.3.6 (a) (i)) | 1 |
Central Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength axle steady bar (5.3.6 (a) (i)) | 1 |
Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
Brake performance not tested due suspension mounting badly corroded (1.2.1 (g)) | 1 |
Emissions not tested due to coolant leak from water pump (8.2.1.2 (d)) | 1 |
Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting cross member and panel holding washer bottle (6.2.2 (d) (i)) | 1 |
Central Fuel tank insecure both fuel tank straps missing (6.1.3 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch. Within 30cm of anti roll bar mounting (5.3.6 (a) (i)) | 1 |
Rear Exhaust silencer likely to become detached (8.1.1 (b) (ii)) | 1 |
Exhaust has a major leak of exhaust gases Cat, centre and rear (6.1.2 (a)) | 1 |
Emissions not tested exhaust blowing badly (8.2.1.2 (d)) | 1 |
Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wing (6.1.1 (c) (i)) | 1 |
Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength @ front tie rod arm mount (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear arm mounting (5.3.6 (a) (i)) | 1 |
Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor seat / mounting , fuel tank anchor point (6.1.1 (c) (i)) | 1 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at jacking point (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength holed next to jacking point (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Front Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
Nearside Front Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Bonnet seriously at risk of opening inadvertently (3.1 (b) (ii)) | 1 |
Parking (secondary brake) on a single line braking system imbalanced across an axle Axle 1 (1.3.1 (b) (i)) | 1 |
Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting INNER WING (6.2.2 (d) (i)) | 1 |
Emissions not tested smoke (8.2.1.2 (d)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength control arm mount (5.3.6 (a) (i)) | 1 |
Nearside Headlamp aim projected beam image is obviously incorrect bulb not seated (4.1.2 (c)) | 1 |
Nearside Front Suspension component pin or bush excessively worn inner Etraccontrol arm bush (5.3.4 (a) (i)) | 1 |
Offside Front Suspension component pin or bush excessively worn inner track control arm bush (5.3.4 (a) (i)) | 1 |
Offside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Rear Sound deadening material insecure exhaust missing (8.1.1 (b) (i)) | 1 |
Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Nearside Front Position lamp missing broken (4.2.1 (a) (ii)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor MARKED YELLOW (5.3.6 (a) (i)) | 1 |
Boot lid cannot be secured in the closed position (6.2.1 (e)) | 1 |
Nearside Rear Shock absorbers has a serious fluid leak | 1 |
Offside Stop lamp(s) likely to become detached (4.3.1 (c) (ii)) | 1 |
Steering column universal joint has excessive wear or play (2.2.2 (c)) | 1 |
Exhaust system insecure (6.1.2 (a)) | 1 |
Horn sound not in accordance with requirements (7.7 (c)) | 1 |
Speedometer clearly inoperative (7.8 (b) (ii)) | 1 |
Nearside Side repeater incorrect colour (4.4.3 (a)) | 1 |
Side repeater incorrect colour both lamps (4.4.3 (a)) | 1 |
Central Prop shaft bearing excessively worn mounting split (6.1.7 (b) (i)) | 1 |
Offside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
Offside Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced middle sill (7.1.1 (a) (i)) | 1 |
Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced middle sill (7.1.1 (a) (i)) | 1 |
Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
Nearside Rear Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
Nearside Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Windscreen wiper not working The operation of the wiper is faulty (3.4 (a)) | 1 |
Offside Front Brake disc significantly and obviously worn Inner face (1.1.14 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wing (5.3.6 (a) (i)) | 1 |