| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 30 |
| Headlamp aim out of alignment | 16 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 15 |
| Brake hose excessively deteriorated | 13 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 12 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 10 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 10 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 10 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 10 |
| Horn not working (7.7 (a)) | 9 |
| Emissions not tested (8.2.1.2 (d)) | 8 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 7 |
| Nearside Rear Shock absorbers has a serious fluid leak | 6 |
| Registration plate lamp issues | 6 |
| Windscreen washer not working | 6 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 6 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 5 |
| Anti-lock braking system warning lamp indicates an ABS fault | 5 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 5 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 5 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 5 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 5 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 4 |
| Brakes imbalanced across an axle | 4 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 4 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 4 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 4 |
| Offside Front Side repeater not working (4.4.1 (a) (ii)) | 4 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 3 |
| Horn sound not in accordance with requirements (7.7 (c)) | 3 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 3 |
| Registration plate issues | 3 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 3 |
| Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 3 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 3 |
| Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 3 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 3 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition (8.1.1 (a)) | 2 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Front brake disc in such a condition that it is seriously weakened | 2 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 2 |
| Offside Rear Shock absorbers has a serious fluid leak | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 2 |
| Nearside Rear Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Offside Rear Brake cable damaged (1.1.15 (a)) | 2 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
| Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 2 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 2 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 2 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 2 |
| Offside Front Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 2 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Windscreen excessively tinted and visibility through swept area of windscreen seriously affected (3.2 (b) (ii)) | 1 |
| Nearside Headlamp light source and lamp not compatible Main beam - LED Fitted (4.1.4 (c)) | 1 |
| Offside Headlamp light source and lamp not compatible Main beam LED fitted (4.1.4 (c)) | 1 |
| Offside Front Bumper insecure (6.1.4 (a) (i)) | 1 |
| Exhaust system insecure Back box clamp missing (6.1.2 (a)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn HUB MOUNTED (5.3.4 (a) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
| Front Lower Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 1 |
| Nearside Front coil spring fractured |2.4.C.1a| | 1 |
| Offside Front coil spring fractured |2.4.C.1a| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Offside Front Suspension arm locating pin insecure |2.4.G.3a| | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Emissions not tested |7.0| | 1 |
| Nearside Rear Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases tailpipe broken (6.1.2 (a)) | 1 |
| Emissions not tested exhaust blow (8.2.1.2 (d)) | 1 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner cill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner cill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer cill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer cill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Battery insecure and likely to fall from carrier battery carrier (4.13 (a) (ii)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits 0.6% co (8.2.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill area (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases rear silencer has multiple holes in (6.1.2 (a)) | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Under battery (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Under airbox (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 1 |
| Exhaust has a major leak of exhaust gases back box (6.1.2 (a)) | 1 |
| Emissions not tested no oil (8.2.1.2 (d)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill Corroded + Holed By Jacking Point. Marked In Yellow Chalk. (6.1.1 (c) (i)) | 1 |
| Offside Rear Brake cable damaged snapped (1.1.15 (a)) | 1 |
| Nearside Integral body structure is fractured and structural rigidity is significantly reduced bottom of b pillar (6.1.1 (a) (i)) | 1 |
| Nearside Side repeater not working missing (4.4.1 (a) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced rear rear diff mount marked with chalk (6.1.1 (c) (i)) | 1 |
| Exhaust has a major leak of exhaust gases x2 (6.1.2 (a)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner wheel arch (6.1.1 (c) (i)) | 1 |
| Parking brake inoperative on one side NSR 43KG
OSR 19KG (1.4.1 (a)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Position lamp adversely affected by the operation of another lamp With indicator. (4.2.3 (c)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Power steering component leaking Rack. (2.1.5 (a)) | 1 |
| Nearside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Brake performance not tested (1.2.1 (g)) | 1 |
| Nearside Front Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Rear Position lamp not working both rears (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill jacking point (5.3.6 (a) (i)) | 1 |
| Offside Front Hydraulic brake calliper insecurely mounted (1.1.16 (c) (i)) | 1 |
| Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
| Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Speedometer cannot be illuminated (7.8 (c) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SILL (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Offside Front Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Exhaust has a major leak of exhaust gases centre joint (6.1.2 (a)) | 1 |
| Nearside Front Brake hose damaged and likely to fail (1.1.12 (a)) | 1 |
| Offside Front Brake hose damaged and likely to fail (1.1.12 (a)) | 1 |
| Front Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Offside Front Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Seat belt not functioning as intended (7.1.2 (c)) | 1 |
| Offside Rear Road wheel more than one fixing loose wheels not seated sqaure (5.2.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill riser / jacking point (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn rear bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Rear Service brake excessively binding Parking brake binding (1.2.1 (f)) | 1 |
| Drivers seat fore and aft adjustment mechanism not functioning as intended. (6.2.5 (b) (i)) | 1 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 1 |
| Emission control equipment missing where fitted as standard exhaust system back half (8.2.1.1 (a)) | 1 |
| Emission control equipment obviously modified (8.2.1.1 (a)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch from in side (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch front inner side (6.2.2 (d) (i)) | 1 |
| Central Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced side sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Emissions not tested exhaust leaking (8.2.1.2 (d)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Offside Rear Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Central Prop shaft bearing housing insecure (6.1.7 (f) (i)) | 1 |
| Offside Indicator switch inoperative (4.4.2 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases exhaust silencer (6.1.2 (a)) | 1 |
| Nearside Front Lower Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Nearside Rear Seat belt buckle missing seat in boot (7.1.2 (d)) | 1 |
| Nearside Rear Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Central Exhaust emissions likely to be affected by an exhaust leak cat to rear section blowing / cat rattling (8.2.1.1 (b)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Brake lever has abnormal movement of levers indicating excessive wear or maladjustment no reserve travel (1.1.15 (f)) | 1 |
| Nearside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Offside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Nearside Front Outer Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill x2 (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill; (7.1.1 (a) (i)) | 1 |
| Nearside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases Box (6.1.2 (a)) | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition Cherry bomb (8.1.1 (a)) | 1 |
| Nearside Rear Rear reflector defective or damaged by more than 50% of the reflecting surface (4.8.1 (a) (ii)) | 1 |
| Central Prop shaft bearing excessively worn (6.1.7 (b) (i)) | 1 |
| Nearside Obligatory indirect vision device missing (3.3 (a)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Brake fluid contaminated (1.8 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength innersill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor to chassis (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 1 |
| Nearside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
| Brake hydraulic reservoir fluid level significantly below minimum level (1.1.10 (d) (ii)) | 1 |
| Central Front Suspension arm attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Rear Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt damaged (7.1.2 (b) (i)) | 1 |
| Nearside Front Lower Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Offside Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Rear Exhaust has a major leak of exhaust gases sill (6.1.2 (a)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Lower Suspension rod pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Lower Suspension rod pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Offside Rear Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Hole in sill near axle mounting point (6.2.2 (d) (i)) | 1 |
| Anti-lock braking system warning lamp does not illuminate (1.6 (a)) | 1 |
| Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Position lamp switch does not operate in accordance with the requirements when switching to dip beem the light switch off (4.2.2 (a)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases behind silencer (6.1.2 (a)) | 1 |
| Front Position lamp not working both front (4.2.1 (a) (ii)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Nearside Front Power steering component leaking Rack (2.1.5 (a)) | 1 |
| Nearside Integral body structure is fractured and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Offside Integral body structure is fractured and structural rigidity is significantly reduced (6.1.1 (a) (i)) | 1 |
| Prop shaft bearing excessively worn (6.1.7 (b) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases section (catalytic convertor) of the (6.1.2 (a)) | 1 |
| Position lamp switch does not illuminate the front and rear position lamps with a single operation (4.2.2 (a)) | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer inner sill at trailing arm mounting badly corroded and holed (5.3.6 (a) (i)) | 1 |