Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 12 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 5 |
Headlamp aim out of alignment | 4 |
Horn not working (7.7 (a)) | 4 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
Nearside Side repeater not working (4.4.1 (a) (ii)) | 3 |
Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 3 |
Registration plate issues | 3 |
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 3 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Windscreen washer not working | 2 |
Fuel cap/sealing device missing (6.1.3 (b) (i)) | 2 |
Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
Brakes imbalanced across an axle | 2 |
Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
Nearside Rear Shock absorbers has a serious fluid leak | 2 |
Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 2 |
Nearside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 2 |
Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 2 |
Anti-lock braking system warning lamp indicates an ABS fault | 2 |
Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
Exhaust emissions carbon monoxide content excessive 7.14 (8.2.1.2 (b)) | 1 |
Offside Rear Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill area holed (5.3.6 (a) (ii)) | 1 |
Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Windscreen wiper not working both (3.4 (a)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength by rear arm (5.3.6 (a) (i)) | 1 |
Exhaust has a major leak of exhaust gases centre (6.1.2 (a)) | 1 |
Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
Emissions not tested (8.2.1.2 (d)) | 1 |
Offside Side repeater incorrect colour (4.4.3 (a)) | 1 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected subframe (5.3.6 (a) (ii)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength on axle mount (5.3.6 (a) (i)) | 1 |
Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Exhaust emits excessive dense blue smoke during acceleration (8.2.1.2 (g)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch holed and corroded (6.1.1 (c) (i)) | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch holed and corroded (6.1.1 (c) (i)) | 1 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
Offside Rear Brake cable damaged (1.1.15 (a)) | 1 |
Nearside Front Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 1 |
Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
Power steering fluid reservoir empty (2.1.5 (b) (ii)) | 1 |
Nearside Power steering ram leaking (2.1.5 (a)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Offside Rear Outer Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill corroded within 30cm of seat belt mounting (7.1.1 (a) (i)) | 1 |
Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Wheel arch/ battery tray corroded (6.1.1 (c) (i)) | 1 |
Offside Front Drivers seat fore and aft adjustment mechanism not functioning as intended. (6.2.5 (b) (i)) | 1 |
Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
Boot lid cannot be secured in the closed position and unable to open (6.2.1 (e)) | 1 |
Prop shaft bearing excessively worn (6.1.7 (b) (i)) | 1 |
Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x2 (5.3.6 (a) (i)) | 1 |
Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Emissions not tested Due to poor running (8.2.1.2 (d)) | 1 |
Nearside Front Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting @ jacking point (6.2.2 (d) (i)) | 1 |
Offside Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting chassis leg (6.2.2 (d) (i)) | 1 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 1 |
Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction (3.1 (a) (ii)) | 1 |
Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both Sides Rear Chassis Rails (5.3.6 (a) (i)) | 1 |
Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both Sides Rear Inner/Lower Wheel Arches (5.3.6 (a) (i)) | 1 |
Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Nearside Rear Outer Sill (5.3.6 (a) (i)) | 1 |
Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both Sides Front Inner Wings (5.3.6 (a) (i)) | 1 |
Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER SILL (5.3.6 (a) (i)) | 1 |
Offside Front Seat belt buckle damaged (7.1.2 (d)) | 1 |
Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting arch (6.2.2 (d) (i)) | 1 |
Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting arch (6.2.2 (d) (i)) | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis leg holed (6.2.2 (d) (i)) | 1 |
Front Service brake imbalanced across an axle poss pads (1.2.1 (b) (i)) | 1 |
Nearside Front Brake hose excessively damaged (1.1.12 (b) (ii)) | 1 |
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 1 |
Nearside Rear Brake hose damaged and likely to fail Not supported bracket corroded off of vehicle (1.1.12 (a)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shock mount (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Axel mounting bracket (5.3.6 (a) (i)) | 1 |
Exhaust has a major leak of exhaust gases center silencer (6.1.2 (a)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch forward of road wheel (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch (5.3.6 (a) (i)) | 1 |
Nearside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Body component corroded and likely to cause injury Wing (6.2.1 (a) (i)) | 1 |
Offside Front Brake prescribed area is excessively corroded Around ABS pump (1.1.21 (e) (i)) | 1 |
Power steering inoperative (2.1.5 (c) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
Offside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
Nearside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Offside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
Offside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Inner sill (5.3.6 (a) (ii)) | 1 |
Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt inner steering gator split (2.1.3 (g) (ii)) | 1 |
Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 1 |
Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Position lamp switch does not operate in accordance with the requirements (4.2.2 (a)) | 1 |
Lower Steering column universal joint has excessive wear or play (2.2.2 (c)) | 1 |
Offside Rear Brake cable has restricted free movement handbrake cable chaffing on exhaust (1.1.15 (e)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength subframe (5.3.6 (a) (i)) | 1 |
Dipswitch operation does not deflect all main beam headlamps to make them dipped beams stuck on main beam (4.1.3 (b)) | 1 |
Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |