| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 18 |
| Headlamp aim out of alignment | 16 |
| Registration plate lamp issues | 11 |
| Windscreen wiper does not clear the windscreen effectively | 10 |
| Parking brake: efficiency below requirements |3.7.B.7| | 5 |
| Service brake: efficiency below requirements |3.7.B.7| | 5 |
| Nearside Stop lamp not working |1.2.1b| | 5 |
| Brake hose excessively deteriorated | 4 |
| Exhaust system not adequately supported |7.1.1| | 4 |
| Brakes imbalanced across an axle | 4 |
| Offside Stop lamp not working |1.2.1b| | 4 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 4 |
| Service brake: efficiency below requirements |3.7.D.4| | 4 |
| Offside Front Direction indicator not working |1.4.A.2c| | 3 |
| Offside Rear fog lamp not working |1.3.2b| | 3 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 3 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 2 |
| Offside Side repeater not working |1.4.A.2c| | 2 |
| Offside Front Seat belt retracting mechanism defective |5.2.5b| | 2 |
| Nearside Headlamp not working on main beam |1.7.5a| | 2 |
| Offside Headlamp not working on main beam |1.7.5a| | 2 |
| Nearside Side repeater not working |1.4.A.2c| | 2 |
| Rear parking brake recording little or no effort | 2 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Battery insecure |1.9.1| | 2 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Windscreen washer not working | 2 |
| Battery insecure and likely to fall from carrier |4.13 |a| |ii|| | 2 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Offside Front Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 2 |
| Spare wheel insecure in carrier (6.1.5 (b) (i)) | 2 |
| Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Rear Exhaust mounting missing |7.1.1b| | 2 |
| Nearside Headlamp insecure (4.1.1 (c)) | 2 |
| Offside Headlamp insecure (4.1.1 (c)) | 2 |
| Exhaust has a major leak of exhaust gases centre (6.1.2 (a)) | 2 |
| Centre Exhaust mounting missing |7.1.1b| | 2 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 2 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Front brake disc in such a condition that it is seriously weakened | 2 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Brake pipe inadequately supported engine compartment |3.6.B.1| | 1 |
| Nearside Front Brake pipe kinked |3.6.B.2b| | 1 |
| Nearside Rear Brake pipe excessively chafed |3.6.B.2c| | 1 |
| Nearside Front Brake pipe fouled by moving parts |3.6.B.2a| | 1 |
| Offside Front Brake pipe fouled by moving parts |3.6.B.2a| | 1 |
| Nearside Front Brake pipe inadequately supported |3.6.B.1| | 1 |
| Rear Brake pipe inadequately clipped axle |3.6.B.1| | 1 |
| Nearside Rear Brake load sensing valve has been removed and was fitted as standard |3.6.E.2| | 1 |
| Offside Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Nearside Front Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 1 |
| Nearside Front Fuel cap/sealing device sealing washer torn |7.2.4c| | 1 |
| Offside Rear Rear position lamp|s| incorrect colour lens damaged |1.1.A.3e| | 1 |
| Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Horn not working |1.6.2a| | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Rear Mechanical brake component has restricted free movement | 1 |
| Rear Stop lamp not working |1.2.1b| | 1 |
| Exhaust has a major leak of exhaust gases manifold (6.1.2 (a)) | 1 |
| Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Front passenger seat insecure |6.2.3| | 1 |
| Steering system excessively rough |2.2.D.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Rear Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Steering rack gaiter split |2.2.D.2d| | 1 |
| Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Offside Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases Silencer (6.1.2 (a)) | 1 |
| Front Suspension component mounting prescribed area fractured significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength body (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength body (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength body (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Rear Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Nearside Front Position lamp not working |4.2.1 |a|| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Front Windscreen wiper not working |3.4 |a|| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced step |7.1.1 |a| |i|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component attachment bracket/mounting likely to become detached airbag mount |5.3.3 |a| |ii|| | 1 |
| Nearside Front Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
| Offside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Obligatory mirror seriously damaged, affecting the rear view (3.3 (b) (ii)) | 1 |
| Registration plate issues | 1 |
| Nearside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Windscreen wiper not working |3.4 |a|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch front and back (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill several places (6.1.1 (c) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill several places (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch (6.1.1 (c) (i)) | 1 |
| Rear Wheel bearing play so excessive it is likely to break up both (5.1.3 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Emissions not tested |7.3.A.1| | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside front brake juddering severely |3.7.A.2b| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
| Fuel pipe leaking |7.2.3| | 1 |
| Front Bumper likely to become detached (6.1.4 (a) (ii)) | 1 |
| Windscreen wiper not working (3.4 (a)) | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Rear Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Position lamp switch does not operate in accordance with the requirements (4.2.2 (a)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Drive shaft bearing excessively worn (6.1.7 (b) (i)) | 1 |
| Offside Rear Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Centre Front Lower engine mounting deteriorated resulting in excessive movement |6.1.D.1a| | 1 |
| Centre Rear Electrical wiring damaged and bare wires exposed |1.9.2c| | 1 |
| Centre Rear Electrical wiring inadequately supported |1.9.2a| | 1 |
| Driver`s door does not latch securely closed |6.2.3 |a|| | 1 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Offside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Offside Front Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
| Fuel cap/sealing device missing (6.1.3 (b) (i)) | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Nearside Parking brake inoperative on one side very poor (1.4.1 (a)) | 1 |
| Drivers door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Fluid leak harmful to the environment or a risk to other road users coolant (8.4.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected inner arch chassis area (5.3.6 (a) (ii)) | 1 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Centre Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Emissions not tested (8.2.1.2 (d)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Fuel system component leaking |7.2.3| | 1 |
| Fuel system component insecure |7.2.1| | 1 |
| Offside Front Upper Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Brake performance unable to be tested leak from front brake pipe (1.2.1 (g)) | 1 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Front Headlamp insecure |1.7.3| | 1 |
| Nearside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Nearside Rear Brake pipe fouled by moving parts |3.6.B.2a| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Lower Engine mounting damaged or deteriorated resulting in excessive movement (6.1.8 (a) (i)) | 1 |
| Rear Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 1 |
| Central Exhaust system insecure (6.1.2 (a)) | 1 |
| Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Rear Brake hose leaking |3.6.A.1| | 1 |
| Brake performance not tested |3.7.A.1| | 1 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 1 |
| Brake hose damaged | 1 |
| Rear brake binding | 1 |
| An item not tested |Manual| | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure is deformed and structural rigidity is significantly reduced sill not been repaired properly (6.1.1 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 1 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Emissions unable to be completed (8.2.1.2 (d)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch x2 (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Rear Upper Vehicle structure strengthening plate or fastening insecure suspension airbag fastening structure beam insecue |6.1.1 |b| |i|| | 1 |
| Offside Front Electrical wiring likely to touch hot or rotating parts driveshaft |4.11 |a| |iii|| | 1 |
| Brake load sensing valve seized and ABS not fitted or inoperative |1.1.17 |c| |ii|| | 1 |
| Front Exhaust has a major leak of exhaust gases pipe leaking |7.1.2| | 1 |
| Central Exhaust system not adequately supported Exhaust mounting rubbers missing | supported by cable ties | |7.1.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Crossmember |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Crossmember |2.4.A.3| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings x2 |6.1.B.2| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded Wheel Arch |2.4.A.3| | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded Wheel Arch |2.4.A.3| | 1 |
| Rear Brake pipe inadequately clipped Across Axle |3.6.B.1| | 1 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
| Offside Front Electrical wiring likely to touch hot or rotating parts drive shaft |4.11 |a| |iii|| | 1 |
| Exhaust system insecure heat sheald |6.1.2 |a|| | 1 |
| Nearside Front Integral body structure is deformed and structural rigidity is significantly reduced inner step |6.1.1 |a| |i|| | 1 |
| Offside Front Integral body structure is deformed and structural rigidity is significantly reduced inner outer step |6.1.1 |a| |i|| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Rear Brake load sensing valve linkage obviously incorrectly adjusted (1.1.17 (b)) | 1 |
| Offside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Offside Battery insecure |1.9.1| | 1 |
| Nearside Battery insecure |1.9.1| | 1 |
| Front Body insecure and dangerous to other road users bumper insecure |6.1.B.1b| | 1 |
| Rear fog lamp not working |1.3.2b| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm pin or bush excessively worn Inner bush to chassis (5.3.4 (a) (i)) | 1 |