| Most common failures | No# failures |
|---|
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 65 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 63 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 31 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 28 |
| Windscreen wiper does not clear the windscreen effectively | 25 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 20 |
| Headlamp aim out of alignment | 19 |
| Brake pipe excessively corroded | 18 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 18 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 16 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 14 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 12 |
| Brakes imbalanced across an axle | 11 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 11 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 10 |
| Electronic power steering warning lamp indicates a system malfunction (2.6 (a)) | 9 |
| Brake hose excessively deteriorated | 9 |
| Horn not working (7.7 (a)) | 8 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 8 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 8 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 8 |
| Nearside Rear Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 8 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 8 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 7 |
| Windscreen washer not working | 7 |
| Stop lamp(s) remains on when the brakes are released (4.3.2 (a) (iii)) | 7 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 7 |
| Registration plate lamp issues | 6 |
| Registration plate issues | 6 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 6 |
| Anti-lock braking system warning lamp indicates an ABS fault | 6 |
| Offside Front Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 5 |
| Front brake disc in such a condition that it is seriously weakened | 5 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 5 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 5 |
| Nearside Rear Direction indicator incorrect colour (4.4.3 (a)) | 5 |
| Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 5 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 5 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 5 |
| Offside Front Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 5 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
| Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 4 |
| Nearside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 4 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 4 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 4 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Nearside Front Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 4 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 4 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Emissions unable to be completed (8.2.1.2 (d)) | 4 |
| Service brake: efficiency below requirements |3.7.B.7| | 3 |
| Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 3 |
| Rear Stop lamp(s) all not working (4.3.1 (a) (iii)) | 3 |
| Offside Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 3 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 3 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 3 |
| Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 3 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 3 |
| Power steering inoperative (2.1.5 (c) (i)) | 3 |
| Rear fog lamp switch inoperative (4.5.3 (a)) | 3 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 3 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 3 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 3 |
| Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 3 |
| Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 3 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 2 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 2 |
| Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Registration plate lamp issues | 2 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Direction indicator adversely affected by the operation of another lamp (4.4.3 (b)) | 2 |
| Offside Rear Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 2 |
| Offside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 2 |
| Offside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 2 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 2 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 2 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Offside Front Seat belt buckle not functioning as intended (7.1.2 (d)) | 2 |
| Offside Front Outer Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
| Electronic power steering not working (2.6 (c)) | 2 |
| Emissions not tested (8.2.1.2 (d)) | 2 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 2 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Offside Rear Upper Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Rear Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 2 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Brake servo defective or ineffective (1.1.10 (a) (i)) | 2 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 2 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 2 |
| Offside Rear Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Front Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 2 |
| Rear brake disc in such a condition that it is seriously weakened | 2 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Suspension system inoperative (5.3.5 (a)) | 2 |
| Offside Front Upper Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Brake performance not tested (1.2.1 (g)) | 2 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 2 |
| Nearside Front Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 2 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Front Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 2 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 2 |
| Nearside Rear Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
| Nearside Rear Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Rear Brake pipe leaking |3.6.A.1| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Windscreen wiper does not clear the windscreen effectively | 1 |
| Supplementary restraint system warning lamp indicates a fault |7.1.6 |a|| | 1 |
| Brake performance not tested |1.2.1 |g|| | 1 |
| Power steering inoperative Light on dash |2.1.5 |c| |i|| | 1 |
| Horn not working |1.6.2a| | 1 |
| Brake pipe excessively corroded | 1 |
| Nearside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Rear Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 1 |
| Brakes imbalanced across an axle | 1 |
| Stop lamp remains on when the brakes are released | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer`s specified limits |8.2.1.2 |a|| | 1 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch)(At fornt (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is inadequately repaired Sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Hydraulic brake calliper inadequately mounted bolts loose (1.1.16 (c) (i)) | 1 |
| Offside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Offside Front Lower Suspension arm corroded and seriously weakened Lower section corroded through + has previously been welded, advise replace. (5.3.3 (b) (i)) | 1 |
| Rear Parking brake inoperative on one side both (1.4.1 (a)) | 1 |
| Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Front Anti-lock braking system wheel speed sensor missing not secure (1.6 (c)) | 1 |
| Central Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Electrical wiring insecure and connectors likely to become disconnected Barrett negative connector (4.11 (a) (ii)) | 1 |
| Nearside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting nsr sill corroded/hole (6.2.2 (d) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear silencer (6.1.2 (a)) | 1 |
| Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Brake pedal anti-slip provision missing (1.1.2 (c)) | 1 |
| Fluid leak harmful to the environment or a risk to other road users rear water (8.4.1 (a) (i)) | 1 |
| Emissions unable to be completed water (8.2.1.2 (d)) | 1 |
| Nearside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Offside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Nearside Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
| Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Front Shock absorbers insecurely attached pinch bolt insecure (5.3.2 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 1 |
| Nearside Front Valve stem seriously damaged exc perished (5.2.3 (j)) | 1 |
| Exhaust has a major leak of exhaust gases manifold (6.1.2 (a)) | 1 |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Rear Fluid leak harmful to the environment or a risk to other road users engine coolant (8.4.1 (a) (i)) | 1 |
| Drivers airbag missing (7.1.5 (a)) | 1 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Body component damaged and likely to cause injury wing (6.2.1 (a) (i)) | 1 |
| Nearside Front Suspension unit damaged or deteriorated and function affected (5.3.5 (b) (i)) | 1 |
| Offside Front Suspension unit damaged or deteriorated and function affected (5.3.5 (b) (i)) | 1 |
| Nearside Rear Suspension unit damaged or deteriorated and function affected (5.3.5 (b) (i)) | 1 |
| Offside Rear Suspension unit damaged or deteriorated and function affected (5.3.5 (b) (i)) | 1 |
| Offside Front Lower Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Upper Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Windscreen wiper not working (3.4 (a)) | 1 |
| Offside Rear Suspension component attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 1 |
| Offside Front Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Offside Rear Shock absorbers damaged to the extent that it does not function resting on bump stop (5.3.2 (b)) | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Brake hose excessively twisted (1.1.12 (b) (ii)) | 1 |
| Offside Front Brake hose excessively twisted (1.1.12 (b) (ii)) | 1 |
| Offside Front Lower Suspension arm corroded and seriously weakened hold and corroded (5.3.3 (b) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer/inner sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer/inner sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Drag link end ball joint has excessive play inner tie rod (2.1.3 (b) (i)) | 1 |
| Nearside Front Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Headlamp has a product on the light source so that the light output is severely reduced both (4.1.4 (b)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Brake pipe leaking on a hydraulic braking system front to rear (1.1.11 (b) (ii)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases Flexi leaking (6.1.2 (a)) | 1 |
| Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Exhaust silencer likely to become detached (8.1.1 (b) (ii)) | 1 |
| Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wing. (5.3.6 (a) (i)) | 1 |
| Offside Front Sub-frame corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure inadequately repaired such that structural rigidity is significantly reduced subframe mounting (6.1.1 (d) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced subframe mounting (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor section (6.1.1 (c) (i)) | 1 |
| Nearside Front Suspension component attachment bracket/mounting likely to become detached front subframe bolt broken near side rear (5.3.3 (a) (ii)) | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Stop lamp(s) adversely affected by the operation of another lamp Indicator (4.3.3 (b)) | 1 |
| Suspension system inoperative Both hydrogas units and rear and associated pipe work very rusty on ferrels (5.3.5 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch inner sill etc (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch inner sill etc (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Rear Sub-frame attachment bracket/mounting insecure (5.3.3 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear flexible (6.1.2 (a)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Emissions unable to be completed fan belt missing (8.2.1.2 (d)) | 1 |
| Nearside Rear Outer Subframe mounting prescribed area is inadequately repaired sill (5.3.6 (a) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed (6.1.1 (c) (i)) | 1 |
| Nearside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits 0.95 (8.2.1.2 (b)) | 1 |
| Offside Rear Suspension arm ball joint excessively worn TOP JOINT WORN (MARKED) (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension arm ball joint excessively worn TOP SWIVEL (MARKED) (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn BOTTOM SWIVEL (MARKED) (5.3.4 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn DROP LINK (5.3.4 (a) (i)) | 1 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Rear Exhaust system insecure Hangers broken (6.1.2 (a)) | 1 |
| Rear Exhaust has a major leak of exhaust gases Exhaust flexi broken (6.1.2 (a)) | 1 |
| Emissions unable to be completed Due to condition of exhaust (8.2.1.2 (d)) | 1 |
| Offside Front Lower Suspension component corroded and seriously weakened arm (5.3.3 (b) (i)) | 1 |
| Nearside Rear Brake pipe leaking on an air braking system three way joint/union (1.1.11 (b) (i)) | 1 |
| Nearside Rear All direction indicators adversely affected by the operation of another lamp (4.4.3 (b)) | 1 |
| Nearside Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Central Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Rear All position lamps adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Nearside Rear Position lamp adversely affected by the operation of another lamp interaction on nearside rear side,stop & indicator lamps (4.2.3 (c)) | 1 |
| Stop lamp(s) remains on when the brakes are released both sides and high level bulbs (4.3.2 (a) (iii)) | 1 |
| Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced n/s & o/s inner & outer sills (6.1.1 (c) (i)) | 1 |
| Front Brake disc significantly and obviously worn corroded (1.1.14 (a) (i)) | 1 |
| Nearside Windscreen wiper not working (3.4 (a)) | 1 |
| All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Hazard warning lamps inoperative (4.4.1 (e)) | 1 |
| Headlamp not working on dipped beam both (4.1.1 (a) (ii)) | 1 |
| Headlamp not working on main beam both (4.1.1 (a) (ii)) | 1 |
| Position lamp not working all (4.2.1 (a) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint likely to become detached bolts loose and nuts missing (5.3.4 (a) (ii)) | 1 |
| Offside Front All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Inner Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Offside Front Suspension arm pin or bush excessively worn + ball joint (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Stop lamp(s) remains on when the brakes are released (4.3.2 (a) (iii)) | 1 |
| Nearside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system burst brake pipe (1.1.11 (b) (ii)) | 1 |
| Nearside Suspension unit leaking (5.3.5 (c)) | 1 |
| Exhaust has a major leak of exhaust gases exhaust flexi pipe (6.1.2 (a)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits Too low (8.2.1.2 (c)) | 1 |
| Exhaust has a major leak of exhaust gases Flexi section blowing (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength REAR FLOOR CORNER [ WITHIN 30 CMS. OF SUBFRAME MOUNTING] (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm corroded and seriously weakened WISHBONE CORRODED (5.3.3 (b) (i)) | 1 |
| Rear Exhaust system insecure NEARSIDE BRACKET COME AWAY FROM SILENCER (6.1.2 (a)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits Exhaust leak (8.2.1.2 (c)) | 1 |
| Nearside Front Track rod end ball joint worn to the extent there is a serious risk of detachment (2.1.3 (b) (ii)) | 1 |
| Nearside Rear Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Seat belt retracting mechanism defective (7.1.2 (e)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Outer Sill Holed. (6.2.2 (d) (i)) | 1 |
| Offside Front Sub-frame corroded to the extent that the rigidity of the assembly is significantly reduced subframe corrosion holed by lower arm mount/chassis mount (6.1.1 (c) (i)) | 1 |
| Power steering inoperative and steering adversely affected P/S warning lamp illuminated (2.1.5 (c) (ii)) | 1 |
| Rear Service brake excessively binding both sides (1.2.1 (f)) | 1 |
| Nearside Front Upper Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Parking brake efficiency below requirements both sides (1.4.2 (a) (i)) | 1 |
| Emissions unable to be completed engine stalled/cut out (8.2.1.2 (d)) | 1 |
| Nearside Front Lower Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Nearside Front Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Nearside Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Nearside Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength closing panel (5.3.6 (a) (i)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting fractured d bush mounting (5.3.3 (b) (ii)) | 1 |
| Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn anti-roll bar link (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Emissions not tested car started to overheat (8.2.1.2 (d)) | 1 |
| Nearside Front Upper Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a)) | 1 |
| Front Suspension system inoperative (5.3.5 (a)) | 1 |
| Rear Suspension system inoperative (5.3.5 (a)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Sub-frame corroded to the extent that the rigidity of the assembly is significantly reduced subframe corroded and holed (6.1.1 (c) (i)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Seat belt buckle not functioning as intended drivers not securing in stalk (7.1.2 (d)) | 1 |
| Anti-lock braking system warning lamp does not illuminate (1.6 (a)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Nearside Front Wheel bearing play so excessive that directional control is impaired (5.1.3 (a) (ii)) | 1 |
| Nearside Side repeater missing (4.4.1 (a) (ii)) | 1 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced both (4.1.4 (b)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Power steering malfunctioning (2.1.5 (a)) | 1 |
| Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Nearside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Front Horn sound not in accordance with requirements (7.7 (c)) | 1 |
| Rear Inner Brake disc significantly and obviously worn AND CORRODED. (1.1.14 (a) (i)) | 1 |
| Offside Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting N/S AND O/S OUTER SILLS (6.2.2 (d) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting O/S SILL BACK TO FLOOR (6.2.2 (d) (i)) | 1 |
| Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting N/S CENTRE BOX/FLOOR (6.2.2 (d) (i)) | 1 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Front Sub-frame insecurely attached Front subframe nearside & offside rear mounting bolts snapped (5.3.3 (a) (i)) | 1 |
| Offside Rear Lower Suspension arm pin or bush excessively worn Rear Arm Inner Bush (5.3.4 (a) (i)) | 1 |
| Nearside Rear Outer Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill panel (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill panel (5.3.6 (a) (i)) | 1 |
| Offside Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits See Emissions Sheet (8.2.1.2 (b)) | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits See Emissions Sheet (8.2.1.2 (c)) | 1 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases Flexy (6.1.2 (a)) | 1 |
| Rear fog lamp switch missing (4.5.3 (a)) | 1 |
| Exhaust catalytic converter missing where one was fitted as standard (8.2.1.1 (a)) | 1 |
| Offside Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Emissions not tested excessive smoke and smell of fuel, likely to fail emissions (8.2.1.2 (d)) | 1 |
| Stop lamp(s) missing (4.3.1 (a) (ii)) | 1 |
| Front Sub-frame corroded and seriously weakened nearside and offside (5.3.3 (b) (i)) | 1 |
| Nearside Rear Lower Suspension arm attachment bracket/mounting insecure (5.3.3 (a) (i)) | 1 |
| Offside Rear Suspension arm pin or bush excessively worn lower arm (5.3.4 (a) (i)) | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn lower arm (5.3.4 (a) (i)) | 1 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Emissions not tested exhaust blowing (8.2.1.2 (d)) | 1 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Nearside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Front Brake disc significantly and obviously worn both sides (1.1.14 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Power steering malfunctioning lamp indicates fault (2.1.5 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer Sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Offside Rear Upper Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Suspension component corroded and seriously weakened lower arm (5.3.3 (b) (i)) | 1 |
| Offside Front Suspension component corroded and seriously weakened lower arm (5.3.3 (b) (i)) | 1 |
| Nearside Front Anti-roll bar pin or bush excessively worn bush missing (5.3.4 (a) (i)) | 1 |
| Nearside Headlamp light source and lamp not compatible Dipped & Main beam (4.1.4 (c)) | 1 |
| Offside Headlamp light source and lamp not compatible Dipped & main beam (4.1.4 (c)) | 1 |
| Offside Rear Service brake excessively binding Cant turn wheel (1.2.1 (f)) | 1 |
| Nearside Rear Sub-frame corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Parking (secondary brake) on a single line braking system imbalanced across an axle Axle 1 (1.3.1 (b) (i)) | 1 |
| Nearside Rear Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Nearside Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill (5.3.6 (a) (ii)) | 1 |
| Nearside Rear Sub-frame corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |