| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 26 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 20 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 19 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 14 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 13 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 12 |
| Registration plate lamp issues | 11 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 11 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 9 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 8 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 8 |
| Horn not working (7.7 (a)) | 8 |
| Brake pipe excessively corroded | 8 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 8 |
| Headlamp aim out of alignment | 7 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 7 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 7 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 6 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 6 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 6 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 6 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 6 |
| Windscreen washer not working | 6 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 6 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 5 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 5 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 5 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 5 |
| Nearside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 5 |
| Offside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 5 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Nearside Rear Position lamp with a multiple light source more than 1/2 not functioning (4.2.1 (a) (ii)) | 4 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 4 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 4 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Registration plate issues | 3 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 3 |
| Offside Rear Shock absorbers has a serious fluid leak | 3 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 3 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 3 |
| Headlamp aim projected beam image is obviously incorrect both (4.1.2 (c)) | 3 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Rear Shock absorbers has a serious fluid leak | 3 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 3 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 3 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 3 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 3 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 3 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 3 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 3 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 3 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Front position lamp(s) not working (1.1.A.3b) | 2 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 2 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 2 |
| Offside Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 2 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Rear fog lamp missing (1.3.2a) | 2 |
| Nearside Rear Shock absorber has a serious fluid leak (2.7.3) | 2 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Seat belt webbing significantly weakened (7.1.2 (b) (ii)) | 2 |
| Nearside Headlamp light source and lamp not compatible (4.1.4 (c)) | 2 |
| Offside Headlamp aim not tested (4.1.2 (b)) | 2 |
| Nearside Headlamp aim not tested (4.1.2 (b)) | 2 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 2 |
| Nearside Rear Lower Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Rear Body component damaged and likely to cause injury lens (6.2.1 (a) (i)) | 2 |
| Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Offside Headlamp aim unable to be tested (4.1.2 (b)) | 2 |
| Emissions unable to be completed (8.2.1.2 (d)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Nearside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
| Nearside Front Tie bar/rod ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Offside Front Tie bar/rod ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt both (2.4.G.2) | 1 |
| Rear Statutory seat belt missing seats (5.1.1) | 1 |
| Offside Rear fog lamp not working (1.3.2b) | 1 |
| Offside Rear fog lamp insecure (1.3.2a) | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2) | 1 |
| Nearside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Electrical wiring insulation in such a condition there is an imminent risk of fire or formation of sparks connector block on nearside battery (4.11 (c) (iii)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Rear fog lamp not working (1.3.2b) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect lens needs a polish (4.1.2 (c)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect lens needs a polish (4.1.2 (c)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt insecure (5.3.4 (b) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt insecure (5.3.4 (b) (ii)) | 1 |
| Offside Front Position lamp not working (4.2.1 (a)) | 1 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen (4.1.2 (a)) | 1 |
| Nearside Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Suspension arm ball joint dust cover no longer prevents the ingress of dirt insecure (5.3.4 (b) (ii)) | 1 |
| Rear brake application uneven | 1 |
| Offside Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Nearside Front Brake disc significantly and obviously worn inner face scored (1.1.14 (a) (i)) | 1 |
| Offside Rear Outer Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Rear fog lamp not working (1.3.2b) | 1 |
| Parking brake lever has no reserve travel (3.1.6b) | 1 |
| Nearside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Front Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Outer Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Outer Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear position lamp(s) not working (1.1.A.3b) | 1 |
| Offside Rear position lamp(s) not working (1.1.A.3b) | 1 |
| Nearside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Nearside Rear Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension component pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Central Sound deadening material insecure flexi pipe fractured (8.1.1 (b) (i)) | 1 |
| Rear Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition rear silencer missing (8.1.1 (a)) | 1 |
| Emissions not tested exhaust loose and part missing (8.2.1.2 (d)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect opauque (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect opaque (4.1.2 (c)) | 1 |
| Central Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn both d bushes (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill and outrigger (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill and outrigger (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Offside Rear fog lamp does not face the rear (4.5.4 (a)) | 1 |
| Offside Rear fog lamp obviously incorrectly positioned (4.5.4 (a)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Rear Body component damaged and likely to cause injury light lens (6.2.1 (a) (i)) | 1 |
| Offside Front Lower Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt Both sides (5.3.4 (b) (ii)) | 1 |
| Front Steering linkage ball joint ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt Both (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill/wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced marked in yellow (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (marked in yellow) (7.1.1 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Crossmember (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Crossmember (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Boot lid component damaged and likely to cause injury tail gate struts not holding up (6.2.1 (a) (i)) | 1 |
| Seat belt not functioning as intended unable to check any rear belts (7.1.2 (c)) | 1 |
| Offside Rear Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 1 |
| Central Rear Exhaust has a major leak of exhaust gases flexi pipe blowing (6.1.2 (a)) | 1 |
| Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn anti-roll bar "D" bush (5.3.4 (a) (i)) | 1 |
| Brakes imbalanced across an axle | 1 |
| Nearside Front Side repeater incorrect colour (4.4.3 (a)) | 1 |
| Offside Front Side repeater incorrect colour (4.4.3 (a)) | 1 |
| Offside Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Offside Rear Anti-roll bar linkage pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
| Rear fog lamp does not face the rear (4.5.4 (a)) | 1 |
| Rear brake disc in such a condition that it is seriously weakened | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill/ chassis (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill/chassis (6.2.2 (d) (i)) | 1 |
| Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting crossmember (6.2.2 (d) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt not functioning as intended (7.1.2 (c)) | 1 |
| Emissions not tested engine wont idle (8.2.1.2 (d)) | 1 |
| Offside Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Offside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Rear Rear reflector missing (4.8.2 (a) (ii)) | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced both of (4.1.4 (b)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis out rig (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting Cross member (6.1.6 (i) (i)) | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced both (4.1.4 (b)) | 1 |
| Nearside Rear Road wheel fixing loose (5.2.1 (a) (i)) | 1 |
| Offside Rear Road wheel fixing loose (5.2.1 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Outer Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired inner sill (6.2.2 (d) (ii)) | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced both (4.1.4 (b)) | 1 |
| Rear fog lamp not working shows white light (4.5.1 (a) (ii)) | 1 |
| Nearside Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Rear Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
| Nearside Rear Vehicle structure is fractured and so weakened within 30cm of a towbar mounting, the towbar is likely to become detached (6.1.6 (i) (ii)) | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced And O/S, lens badly deteriorated. (4.1.4 (b)) | 1 |
| Fuel cap/sealing device ineffective Fuel cap is not secure, non locking type fitted. (6.1.3 (b) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill corroded (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill corroded (6.1.1 (c) (i)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect X2 NSF/OSF MACHINE POLISH LENS. BLUE TINT BULBS FITTED. (4.1.2 (c)) | 1 |
| Offside Rear fog lamp does not emit a steady red light SHOWS WHITE. (4.5.4 (a)) | 1 |
| Position lamp not working all (4.2.1 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases flexi (6.1.2 (a)) | 1 |
| Nearside Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
| Nearside Rear Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
| Nearside Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
| Anti-lock braking system warning lamp indicates an ABS fault | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength radiator crossmember (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength radiator crossmember (5.3.6 (a) (i)) | 1 |
| Front brake disc in such a condition that it is seriously weakened | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Rear Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Lower Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Front Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed due to major leak (8.2.1.2 (d)) | 1 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill - small hole (6.1.1 (c) (i)) | 1 |
| Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Cross member corroded on corners (6.1.1 (c) (i)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Offside Oil leaking continuously from transmission posing a serious risk to road safety gearbox, pipe to hose connection (8.4.1 (a) (ii)) | 1 |
| Brake performance unable to be tested (1.2.1 (g)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Oil leaking excessively from transmission (8.4.1 (a) (i)) | 1 |
| Vehicle structure excessively corroded within 30cm of towbar mounting Both rear corner sections (6.1.6 (i) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both rear inner sills (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced Offside centre inner sill (7.1.1 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both front inner sills (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill area holed (6.1.1 (c) (i)) | 1 |
| Offside Front Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect Both side (4.1.2 (c)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed due to condition of exhaust system (8.2.1.2 (d)) | 1 |
| Exhaust has a major leak of exhaust gases at rear section (6.1.2 (a)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill area affected (6.1.1 (c) (i)) | 1 |
| Nearside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 1 |
| Nearside Front Steering linkage ball joint modification unsafe (2.1.3 (f) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced BOTH (4.1.4 (b)) | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn DROPLINK (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn DROPLINK (5.3.4 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn DROPLINK (5.3.4 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn DROPLINK (5.3.4 (a) (i)) | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view (3.3 (b) (ii)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn drop link (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn drop link (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill to outrigger (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill to outrigger (6.1.1 (c) (i)) | 1 |
| Offside Headlamp insecure (4.1.1 (c)) | 1 |
| Rear Brake disc significantly and obviously worn X2 (1.1.14 (a) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Steering linkage ball joint ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Seat belt retracting mechanism defective front row (7.1.2 (e)) | 1 |
| Exhaust has a major leak of exhaust gases down pipe (6.1.2 (a)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Rear Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Position lamp not working side light (4.2.1 (a) (ii)) | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Valve stem seriously damaged (5.2.3 (j)) | 1 |
| Offside Front Valve stem seriously damaged (5.2.3 (j)) | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced and Outer sill (6.1.1 (c) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced and Outer sill (6.1.1 (c) (i)) | 1 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member (6.1.1 (c) (i)) | 1 |
| Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Both Sides (6.2.2 (d) (i)) | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced Both Sides (4.1.4 (b)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a)) | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |