Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 19 |
Exhaust emissions exceed default limit of 1.5m-1 (8.2.2.2 (b)) | 9 |
Offside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 7 |
Headlamp aim out of alignment | 6 |
Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 5 |
Engine MIL inoperative or indicates a malfunction (8.2.2.2 (g)) | 4 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 4 |
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 4 |
Nearside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 3 |
Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 3 |
Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 3 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 2 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
Undertray likely to become detached (6.2.1 (a) (ii)) | 2 |
Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
Exhaust emissions exceed manufacturers specified limit 0.52 (8.2.2.2 (a)) | 2 |
Windscreen washer not working | 2 |
Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
Central Rear Seat belt not functioning as intended (7.1.2 (c)) | 2 |
Rear brake disc in such a condition that it is seriously weakened | 2 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
Registration plate issues | 2 |
Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 2 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 2 |
Offside Front All position lamps not working |4.2.1 |a|| | 1 |
Front Battery insecure |1.9.1| | 1 |
Nearside Front Coil spring fractured or broken |5.3.1 |b| |i|| | 1 |
Offside Rear wheel bearing has excessive play |2.6.2| | 1 |
Parking brake: efficiency below requirements |3.7.B.7| | 1 |
Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
Emissions not tested no oil in engine (8.2.2.2 (e)) | 1 |
Offside Front Inner Brake disc significantly and obviously worn face (1.1.14 (a) (i)) | 1 |
Nearside Front Headlamp aim not tested (4.1.2 (b)) | 1 |
Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
Offside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 1 |
Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill corroded and holed behind cover (7.1.1 (a) (i)) | 1 |
Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced Sill corroded and holed behind cover (7.1.1 (a) (i)) | 1 |
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor to sill holed (7.1.1 (a) (i)) | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Floor to sill holed (7.1.1 (a) (i)) | 1 |
Nearside Rear Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
Offside Rear Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Headlamp aim not tested (4.1.2 (b)) | 1 |
Offside Rear Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 1 |
Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Nearside Front Lower Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
Rear Suspension arm corroded and seriously weakened Nearside and Offside (5.3.3 (b) (i)) | 1 |
Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced corroded holes in outer sill (marked yellow) (6.1.1 (c) (i)) | 1 |
Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced corroded hole in outer sill (marked yellow) (6.1.1 (c) (i)) | 1 |
Offside Front Headlamp aim projected beam image is obviously incorrect main beam bulb in wrong (4.1.2 (c)) | 1 |
Offside Rear Road wheel has a welding defect (5.2.2 (a)) | 1 |
Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
Offside Front Seat belt webbing significantly weakened (7.1.2 (b) (ii)) | 1 |
Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 1 |
Nearside Rear Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Rear Anti-roll bar pin or bush excessively worn Both side (5.3.4 (a) (i)) | 1 |
Nearside Rear Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b)) | 1 |
Nearside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
Nearside Front Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
Offside Front Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
Offside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
Nearside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Rear Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Front Lower Suspension arm pin or bush excessively worn rear bush (5.3.4 (a) (i)) | 1 |
Engine MIL inoperative or indicates a malfunction engine management light on all the time (8.2.1.2 (h)) | 1 |
Rear Stop lamp(s) remains on when the brakes are released brake lights sticking in the on position (4.3.2 (a) (iii)) | 1 |
Nearside Rear Coil spring fractured or broken spring broken (5.3.1 (b) (i)) | 1 |
Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill area at rear corroded and holed (6.1.1 (c) (i)) | 1 |
Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill area at rear corroded and holed (6.1.1 (c) (i)) | 1 |
Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Rear Suspension arm pin or bush excessively worn front trailing arm bush worn (5.3.4 (a) (i)) | 1 |
Nearside Headlamp aim not tested (4.1.2 (b)) | 1 |
Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill holed (5.3.6 (a) (i)) | 1 |
Nearside Front Service brake lagging in operation (1.2.1 (d)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor section, within 30cm of seat mounting (6.1.1 (c) (i)) | 1 |
Offside Rear Service brake grabbing severely (1.2.1 (c)) | 1 |
Reversing lamp inoperative Both (4.6.1 (a)) | 1 |
Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rear outer sill (5.3.6 (a) (i)) | 1 |
Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rear outer sill (5.3.6 (a) (i)) | 1 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Reversing lamp inoperative (4.6.1 (a)) | 1 |
Nearside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
Offside Rear Suspension arm pin or bush excessively worn OSR trailing arm front bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Fuel pipe leaking front to rear (6.1.3 (b) (i)) | 1 |
Offside Rear Suspension arm pin or bush excessively worn Trailing arm bush (5.3.4 (a) (i)) | 1 |
Offside Front Drivers door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
Offside Rear Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Nearside Rear Seat belt buckle not functioning as intended (7.1.2 (d)) | 1 |
Rear Reversing lamp inoperative (4.6.1 (a)) | 1 |
Nearside Rear Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
Offside Rear Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Brake pedal anti-slip provision worn smooth worn through (1.1.2 (c)) | 1 |
Nearside Rear Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
Nearside Front Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
Nearside Rear Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength mount corroded and holed (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Nearside Rear Brake hose connection leaking on a hydraulic braking system union on calliper (1.1.12 (c) (ii)) | 1 |
Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 1 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Front brake disc in such a condition that it is seriously weakened | 1 |
Front Brake lining(s) less than 1.5 mm thick both sides (1.1.13 (a) (ii)) | 1 |
Nearside Front Drag link end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Rear Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer seal corroded (marked yellow) (6.1.1 (c) (i)) | 1 |
Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Nearside Rear Hydraulic brake calliper leaking and braking performance affected (1.1.16 (b) (ii)) | 1 |
Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Suspension arm pin or bush excessively worn both sides rear (5.3.4 (a) (i)) | 1 |
Nearside Rear Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
Nearside Rear Suspension arm ball joint dust cover no longer prevents the ingress of dirt Bottom arm (5.3.4 (b) (ii)) | 1 |
Offside Rear Suspension arm ball joint dust cover no longer prevents the ingress of dirt Bottom arm (5.3.4 (b) (ii)) | 1 |
Nearside Rear Anti-roll bar linkage attachment bracket/mounting likely to fail (5.3.3 (b) (ii)) | 1 |
Nearside Front Brake hose excessively twisted fouling bracket (1.1.12 (b) (ii)) | 1 |
Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill corroded (5.3.6 (a) (i)) | 1 |
Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill corroded (5.3.6 (a) (i)) | 1 |
Offside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
Offside Rear Valve stem seriously damaged (5.2.3 (j)) | 1 |
Offside Front Valve stem seriously damaged (5.2.3 (j)) | 1 |
Fuel tank leaking (6.1.3 (b) (i)) | 1 |
Engine MIL inoperative or indicates a malfunction management light on all the time (8.2.1.2 (h)) | 1 |
Nearside Rear Hydraulic brake calliper leaking calliper leaking (1.1.16 (b) (i)) | 1 |