| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 40 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 23 |
| Windscreen wiper does not clear the windscreen effectively | 14 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 13 |
| Front brake disc in such a condition that it is seriously weakened | 10 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 6 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
| Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 4 |
| Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 4 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 4 |
| Nearside Rear Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 4 |
| Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 4 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 3 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 3 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Stop lamp(s) remains on when the brakes are released (4.3.2 (a) (iii)) | 3 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 3 |
| Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 3 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Offside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
| Brake pipe excessively corroded | 2 |
| Nearside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 2 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Offside Rear Lower Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 2 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Hazard warning lamps inoperative (4.4.1 (e)) | 2 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Rear Shock absorbers has a serious fluid leak | 2 |
| Nearside Rear Shock absorbers has a serious fluid leak | 2 |
| Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 2 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 2 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 2 |
| Exhaust on a vehicle fitted with a diesel particulate filter emits visible smoke of any colour (8.2.2.2 (d)) | 2 |
| Windscreen washer not working | 2 |
| Nearside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen |1.8.B.1| | 1 |
| Horn sounds harsh or grating |1.6.2e| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Offside Rear Coil spring fractured or broken |5.3.1 |b| |i|| | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
| Offside Rear Hydraulic brake calliper leaking leaking from handbrake cable lever seal |1.1.16 |b| |i|| | 1 |
| Supplementary restraint system warning lamp indicates a fault |7.1.6 |a|| | 1 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Hydraulic brake calliper leaking and braking performance affected (1.1.16 (b) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases front flexi mounting holed where welded to exhaust/corroded (6.1.2 (a)) | 1 |
| Emissions not tested exhaust holed (8.2.1.2 (d)) | 1 |
| Offside Rear Brake lever has restricted free movement handbrake lever seized fully on (1.1.15 (e)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
| Nearside Front Inner Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Front Inner Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt insecure (6.1.7 (g) (ii)) | 1 |
| Brake performance not tested due to fail items (1.2.1 (g)) | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn [front bush] (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension arm pin or bush excessively worn [front bush] (5.3.4 (a) (i)) | 1 |
| Central Rear Seat belt not functioning as intended cant pull out (7.1.2 (c)) | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
| Anti-roll bar pin or bush excessively worn both rear D bushes (5.3.4 (a) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced seal (6.1.1 (c) (i)) | 1 |
| Rear brake disc in such a condition that it is seriously weakened | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill holed and corroded within 12". (5.3.6 (a) (i)) | 1 |
| Rear Brake disc significantly and obviously worn Both. Inner face. (1.1.14 (a) (i)) | 1 |
| Nearside Rear Other passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Offside Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
| Offside Headlamp incorrect colour (4.1.4 (a)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength and inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Offside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| Nearside Headlamp aim not tested (4.1.2 (b)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits .45% (8.2.1.2 (b)) | 1 |
| Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Front Headlamp insecure tighten up mounting bolt (4.1.1 (c)) | 1 |
| Nearside Rear Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced o/s and n/s inner and outer sills (6.1.1 (c) (i)) | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s and n/s inner sills (5.3.6 (a) (i)) | 1 |
| Rear Suspension arm corroded and seriously weakened o/s and n/s (5.3.3 (b) (i)) | 1 |
| Emissions not tested oil burning on exhaust (8.2.1.2 (d)) | 1 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Emissions not tested exhaust (8.2.1.2 (d)) | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Sub-frame pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Sub-frame pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Brakes imbalanced across an axle | 1 |
| Rear Seat belt not functioning as intended Centre belt not pulling out (7.1.2 (c)) | 1 |
| Oil leaking excessively from engine Rear main oil seal (8.4.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Bottom of a post outer sill area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill area (5.3.6 (a) (i)) | 1 |
| Nearside Front Bumper insecure (6.1.4 (a) (i)) | 1 |
| Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Bonnet primary retaining device ineffective (3.1 (c)) | 1 |
| Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill/floor (5.3.6 (a) (i)) | 1 |
| Offside Obligatory mirror does not provide a view to the rear (3.3 (c)) | 1 |
| Offside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect kick up to offside (4.1.2 (c)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill holed and corroded within 12" of mounting. (5.3.6 (a) (i)) | 1 |
| Nearside Rear Coil spring mounting corroded and seriously weakened spring pan (5.3.1 (b) (i)) | 1 |
| Offside Rear Coil spring mounting corroded and seriously weakened spring pan (5.3.1 (b) (i)) | 1 |
| Nearside Rear Inner Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt gaiter split (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Engine MIL inoperative or indicates a malfunction (8.2.2.2 (g)) | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Offside Front Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases front pipe at joint to flexi section holed (6.1.2 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor pan to sill - in seat mount area (7.1.1 (a) (i)) | 1 |
| Offside Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 1 |
| Nearside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Brake performance unable to be tested (1.2.1 (g)) | 1 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Brake hose excessively deteriorated | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Anti-lock braking system warning lamp indicates an ABS fault | 1 |
| Offside Front Wheel bearing play so excessive that directional control is impaired (5.1.3 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Outer sill (6.2.2 (d) (ii)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired Outer sill (6.2.2 (d) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases Pipe (6.1.2 (a)) | 1 |
| Registration plate lamp issues | 1 |
| Nearside Front Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Indicator switch inoperative (4.4.2 (a) (ii)) | 1 |
| Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Fuel tank insecure fuel tank strap corroded, insecure (6.1.3 (a) (i)) | 1 |
| Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt drop link (5.3.4 (b) (ii)) | 1 |
| Brake fluid contaminated (1.8 (a)) | 1 |
| Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt NS & OS (5.3.4 (b) (ii)) | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Emissions unable to be completed due too miss fire from engine (8.2.1.2 (d)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Brake performance unable to be tested 4x4 needs decelerometer but engine is misfiring driving not safe (1.2.1 (g)) | 1 |
| Nearside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Outer Position lamp showing white light to the rear bulb not in holder (4.2.3 (a) (ii)) | 1 |
| Offside Rear Stop lamp(s) emits other than a steady red light bulb not in holder (4.3.3 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an induction leak (8.2.2.1 (b)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Rear Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 1 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Exhaust emissions exceed manufacturers specified limit Plate limit 1.46 (8.2.2.2 (a)) | 1 |
| Power steering inoperative (2.1.5 (c) (i)) | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 1 |