Most common failures | No# failures |
---|
Brake pipe excessively corroded | 262 |
Parking brake: efficiency below requirements |3.7.B.7| | 216 |
Headlamp aim out of alignment | 173 |
Rear parking brake recording little or no effort | 93 |
Registration plate lamp issues | 91 |
Horn not working |1.6.2a| | 67 |
Windscreen wiper does not clear the windscreen effectively | 67 |
Brakes imbalanced across an axle | 57 |
Rear brake binding | 55 |
Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 50 |
Service brake: efficiency below requirements |3.7.B.7| | 49 |
Brake hose excessively deteriorated | 43 |
Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 42 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 39 |
Offside Stop lamp not working |1.2.1b| | 37 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 36 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 35 |
Nearside Stop lamp not working |1.2.1b| | 34 |
Fuel system component leaking |7.2.3| | 33 |
Registration plate issues | 32 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 31 |
Offside Rear fog lamp not working |1.3.2b| | 30 |
Offside Front Shock absorber has a serious fluid leak |2.7.3| | 30 |
Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 29 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 28 |
Fuel tank leaking |7.2.3| | 28 |
Offside Front position lamp|s| not working |1.1.A.3b| | 28 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 28 |
Offside rear brake recording little or no effort |3.7.B.5a| | 27 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 26 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 25 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 25 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 22 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 20 |
Offside Rear rear brake recording little or no effort |3.7.B.5a| | 20 |
Front Sub-frame corroded and seriously weakened |2.4.G.1| | 19 |
Offside Side repeater not working |1.4.A.2c| | 18 |
Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 17 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 17 |
Nearside Side repeater not working |1.4.A.2c| | 16 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 16 |
Exhaust has a major leak of exhaust gases |7.1.2| | 16 |
Windscreen has damage | 16 |
Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 16 |
Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 16 |
Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 15 |
Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 15 |
Front brake application uneven | 13 |
Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 13 |
Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 13 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 13 |
Emissions not tested |7.0| | 13 |
Front Windscreen wiper blade deteriorated |8.2.2| | 13 |
Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 12 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 12 |
Offside Front Side repeater not working |1.4.A.2c| | 12 |
Fuel pipe leaking |7.2.3| | 11 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 11 |
Steering column top mounting bracket insecure |2.1.2d| | 11 |
Rear Mechanical brake component has restricted free movement | 11 |
Brake hose has insufficient room to move | 11 |
Offside Headlamp not working on dipped beam |1.7.5a| | 11 |
Parking brake lever, pawl mechanism pivots or their associated mountings are insecure |3.1.4b| | 11 |
Offside Rear Stop lamp not working |1.2.1b| | 11 |
Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 10 |
Rear brake application uneven | 10 |
Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 10 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 10 |
Nearside Rear Stop lamp not working |1.2.1b| | 10 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 9 |
Offside Front Shock absorber has negligible damping effect |2.7.5| | 9 |
Brake pedal spongy |3.3.B.1b| | 9 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 9 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 9 |
Offside Front Sub-frame corroded and seriously weakened |2.4.G.1| | 9 |
Nearside Front Side repeater not working |1.4.A.2c| | 9 |
Rear Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 9 |
Offside Rear Rear fog lamp not working |1.3.2b| | 9 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 8 |
Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 8 |
Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 8 |
Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
Offside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 8 |
Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 8 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
Parking brake lever has no reserve travel |3.1.6b| | 8 |
Brake load sensing valve linkage seized |3.6.E.3| | 7 |
Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 7 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 7 |
Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 7 |
Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 7 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 7 |
Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 7 |
Windscreen wiper blade insecure | 7 |
Front brake disc in such a condition that it is seriously weakened | 7 |
Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 7 |
Rear Brake load sensing valve linkage seized |3.6.E.3| | 6 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 6 |
Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 6 |
Front position lamp|s| not working |1.1.A.3b| | 6 |
Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 6 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 6 |
Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 6 |
Nearside Rear Shock absorber has an excessively worn bush |2.7.4| | 6 |
Centre Windscreen wiper blade deteriorated |8.2.2| | 6 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 6 |
Exhaust system not adequately supported |7.1.1| | 6 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 6 |
Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 6 |
Offside Rear Shock absorber has an excessively worn bush |2.7.4| | 6 |
Nearside Rear Shock absorber has negligible damping effect |2.7.5| | 6 |
Nearside Front Shock absorber has negligible damping effect |2.7.5| | 6 |
Offside Steering rack gaiter insecure |2.2.D.2d| | 6 |
Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 5 |
Fuel cap/sealing device mounting flange/sealing method defective |7.2.4c| | 5 |
Rear Exhaust system not adequately supported |7.1.1| | 5 |
Driver`s seat insecure |6.2.A.1| | 5 |
Nearside Steering rack gaiter split |2.2.D.2d| | 5 |
Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
Offside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 5 |
Centre Exhaust mounting missing |7.1.1b| | 5 |
Front Fuel pipe leaking |7.2.3| | 5 |
Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
An item not tested |Manual| | 5 |
Fuel hose leaking |7.2.3| | 5 |
Steering column top bearing excessively worn |2.1.2c| | 5 |
Offside front brake binding |3.7.B.1| | 5 |
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
Offside Rear Shock absorber has negligible damping effect |2.7.5| | 5 |
Nearside Rear Brake lever has restricted free movement |3.5.1k| | 5 |
Front Horn not working |1.6.2a| | 5 |
Nearside Side repeater missing |1.4.A.2b| | 5 |
Nearside Steering rack gaiter insecure |2.2.D.2d| | 5 |
Nearside Rear Upper Shock absorber has an excessively worn bush |2.7.4| | 4 |
Offside Rear Upper Shock absorber has an excessively worn bush |2.7.4| | 4 |
Exhaust has part of the system excessively deteriorated |7.1.1a| | 4 |
Offside Rear wheel bearing rough when rotated |2.6.1| | 4 |
Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 4 |
Hazard warning switch faulty |1.4.B.1d| | 4 |
Nearside front brake binding |3.7.B.1| | 4 |
Rear Exhaust has a part missing |7.1.1a| | 4 |
Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
Parking brake lever has excessive side play in the pivot and may disengage |3.1.4a| | 4 |
Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 4 |
Nearside Front Ball joint has excessive play |2.2.B.1f| | 4 |
Offside Front front brake binding |3.7.B.1| | 4 |
Parking brake lever, pawl mechanism pivot|s| or their associated mountings locking device insecure |3.1.4b| | 4 |
Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 4 |
Centre Parking brake lever has excessive side play in the pivot and may disengage |3.1.4a| | 4 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
Brake pedal has insufficient reserve movement |3.3.A.5| | 4 |
Offside Front Direction indicator incomplete |1.5.A1b| | 4 |
Offside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 4 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
Stop lamp remains on when the brakes are released | 4 |
Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 4 |
Nearside Rear Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 4 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 4 |
Nearside Rear wheel bearing rough when rotated |2.6.1| | 4 |
Nearside Front Brake pipe inadequately supported |3.6.B.1| | 3 |
Offside Front Brake pipe inadequately clipped |3.6.B.1| | 3 |
Nearside Front Direction indicator insecure |1.4.A.2b| | 3 |
Offside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 3 |
Brake hose damaged | 3 |
Steering column movement between the shaft and steering wheel |2.1.2b| | 3 |
Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 3 |
Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 3 |
Offside Rear Brake linkage has restricted free movement |3.5.1k| | 3 |
Offside Rear Brake pipe leaking |3.6.A.1| | 3 |
Offside Steering rack insecure |2.2.B.1a| | 3 |
Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.4.B.1| | 3 |
Centre Rear Statutory seat belt missing |5.1.1| | 3 |
Nearside Headlamp not working on main beam |1.7.5a| | 3 |
Offside Front Ball joint has excessive play |2.2.B.1f| | 3 |
Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 3 |
Rear Rear passenger seat cannot be secured in the upright position. |6.2.3| | 3 |
Offside Suspension arm has excessive play in a ball joint |2.4.G.2| | 3 |
Offside Headlamp not working on main beam |1.7.5a| | 3 |
Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 3 |
Parking brake lever defective so that it cannot be satisfactorily operated |3.1.3c| | 3 |
Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 3 |
Centre Exhaust system not adequately supported |7.1.1| | 3 |
Offside Steering rack gaiter split |2.2.D.2d| | 3 |
Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Front Lower Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
Offside Rear Statutory seat belt missing |5.1.1| | 3 |
Offside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 3 |
Nearside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 3 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
Rear Stop lamp not working |1.2.1b| | 3 |
Nearside Front wheel bearing rough when rotated |2.5.A.2| | 3 |
Brake load sensing valve has been disconnected and was fitted as standard |3.6.E.2| | 3 |
Brake pedal creeps down when held under pressure |3.3.B.1a| | 3 |
Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Nearside Rear Rear fog lamp not working |1.3.2b| | 3 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Front brake disc excessively pitted |3.5.1h| | 3 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
Brake load sensing valve linkage obviously incorrectly adjusted |3.6.E.3| | 3 |
Offside Rear Brake pivot has restricted free movement |3.5.1k| | 3 |