| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 63 |
| Registration plate lamp issues | 26 |
| Windscreen wiper does not clear the windscreen effectively | 25 |
| Headlamp aim out of alignment | 20 |
| Horn not working |1.6.2a| | 14 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 12 |
| Brakes imbalanced across an axle | 9 |
| Offside Stop lamp not working |1.2.1b| | 7 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 6 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 6 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 5 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 5 |
| Horn not working (7.7 (a) (ii)) | 5 |
| Parking brake: efficiency below requirements |3.7.B.7| | 4 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Exhaust system not adequately supported |7.1.1| | 4 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
| Centre Exhaust system not adequately supported |7.1.1| | 4 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Emissions not tested |7.0| | 3 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Nearside Stop lamp not working |1.2.1b| | 3 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 3 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 3 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 2 |
| Service brake: efficiency below requirements |3.7.B.7| | 2 |
| Nearside Rear Stop lamp not working |1.2.1b| | 2 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 2 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
| Registration plate issues | 2 |
| Battery insecure |1.9.1| | 2 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 2 |
| Offside Front brake disc excessively pitted |3.5.1h| | 2 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Offside Rear fog lamp not working |1.3.2b| | 2 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 2 |
| Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 2 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Rear parking brake recording little or no effort | 2 |
| Windscreen washer not working | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Windscreen wiper not working (3.4 (a)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Front Headlamp levelling device inoperative (4.1.5 (a)) | 2 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 2 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 2 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 2 |
| Front passenger seat insecure |6.2.3| | 1 |
| Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x 2 |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Upper strut mounting prescribed area |2.4.A.3| | 1 |
| Rear Brake pipe leaking |3.6.A.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Centre Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Brake performance not tested |3.7.A.1| | 1 |
| Offside Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
| Offside Rear position lamp|s| has a product on the light source so it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Front Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Nearside Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 1 |
| Nearside Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Offside Rear reflector missing |1.5.1a| | 1 |
| Nearside Rear Wheel bolt|s| missing |4.2.A.1e| | 1 |
| Offside Rear Wheel bolt|s| missing |4.2.A.1e| | 1 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Front brake application uneven | 1 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
| Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Windscreen wiper blade insecure | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Brake valve leaking |3.6.A.1| | 1 |
| Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Windscreen has damage | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Inner Front Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Front Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Offside Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 1 |
| Brake pedal anti-slip provision incomplete |3.3.A.1b| | 1 |
| Nearside Inner Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Leaf spring fractured |2.4.B.1a| | 1 |
| Brake load sensing valve inoperative |3.6.E.3| | 1 |
| Nearside Front Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Offside Front Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Nearside Inner Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Headlamp insecure |1.7.3| | 1 |
| Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Brake pipe seriously damaged |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
| Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Nearside Rear Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Macpherson strut upper support bearing is rough in operation |2.5.B.1b| | 1 |
| Offside Front Macpherson strut upper support bearing is rough in operation |2.5.B.1b| | 1 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Nearside Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
| Offside Driver`s door hinge insecure |6.2.B.2| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Centre Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Side repeater not working |1.4.A.2c| | 1 |
| Exhaust engine idle speed too high |7.3.D.1| | 1 |
| Nearside Rear reflector not red in colour |1.5.1d| | 1 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded floor & inner arch panels |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded floor & inner arch panel |2.4.A.3| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded floor pan, inner sill & rear cross member |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded floor pan, inner sill & rear cross member |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner arch panel |2.4.A.3| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded inner & outer sill panel |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded inner & outer sill panel |5.2.6| | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Upper Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Driver`s seat insecure |6.2.A.1| | 1 |
| Brake hose excessively deteriorated | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Upper Steering system excessively tight |2.2.D.1| | 1 |
| Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Fuel cap/sealing device missing |6.1.3 |b| |i|| | 1 |
| Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.D.1| | 1 |
| Brake cable has a seized clevis joint pivot |3.5.1c| | 1 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Power steering pump drive system missing |2.3.6| | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Steering system excessively tight |2.2.D.1| | 1 |
| Horn not working |7.7 |a| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Nearside Inner Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Offside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Stop lamp not working |1.2.1b| | 1 |
| Brake load sensing valve seized |3.6.E.3| | 1 |
| Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner arch/chassis |5.3.6 |a| |i|| | 1 |
| Nearside Front Brake pipe leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 1 |
| Offside Side repeater not working |4.4.1 |a| |ii|| | 1 |
| Headlamp levelling device inoperative offside/nearside |4.1.5 |a|| | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Leaf spring anchor bracket bolt missing |2.4.B.6c| | 1 |
| Offside Rear Leaf spring anchor bracket bolt missing |2.4.B.6c| | 1 |
| Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner quarter (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner quarter (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s/f floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Offside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Nearside Headlamp aim not tested (4.1.2 (b)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Headlamp has a product on the light source so that the light output is severely reduced dim (4.1.4 (b)) | 1 |
| Nearside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at rear spring hanger,inner/outer sill (5.3.6 (a) (i)) | 1 |
| Central Windscreen damaged and affecting the drivers view of the road Substantial crack in glass (3.2 (a) (ii)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced & Suspension component mounting prescribed area (7.1.1 (a) (i)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front shackle marked in yellow (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear shackle marked in yellow (5.3.6 (a) (i)) | 1 |
| Speedometer clearly inoperative (7.8 (b) (ii)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wing (6.1.1 (c) (i)) | 1 |
| Offside Front Upper Brake master cylinder/servo mounting prescribed area is excessively corroded Inner wheelarch x2 (1.1.21 (e) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Upper wheelarch x2 (5.3.6 (a) (i)) | 1 |
| Nearside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Whole of outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting suspension mount (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure inadequately repaired such that structural rigidity is significantly reduced strut / inner wheel arch
REPAIRED WITH BODY FILLER (6.1.1 (d) (i)) | 1 |
| Nearside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced inner sill
REPAIRED WITH BODY FILLER (6.1.1 (d) (i)) | 1 |
| Nearside Front Integral body structure inadequately repaired such that structural rigidity is significantly reduced wheel arch above jacking point
REPAIRED WITH BODY FILLER (6.1.1 (d) (i)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect refletor (4.1.2 (c)) | 1 |
| Offside Headlamp reflector seriously defective (4.1.1 (b) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
| Nearside Rear Leaf spring shackle pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Leaf spring shackle pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength spring hanger support bracket area (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength spring hanger support bracket area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rearmost (5.3.6 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits Hydrocarbon & lambda just passed (8.2.1.2 (b)) | 1 |
| Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Offside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
| Front Service brake excessively binding offside/nearside (1.2.1 (f)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Rear Service brake excessively binding offside/nearside (1.2.1 (f)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength rear mount (5.3.6 (a) (i)) | 1 |