MOT History from tests of petrol FIAT DUCATOs year 2000

Review the list of common FIAT DUCATO failures below or to perform a specific mot history check on your FIAT then use our popular KnowYourCar service

mot history

Pass percent:57.60%

(The average a petrol FIAT DUCATO year 2000 passes without issue)

Based on:566 MOT Tests

Most common failures	No# failures
Brake pipe excessively corroded	54
Windscreen wiper does not clear the windscreen effectively	50
Headlamp aim out of alignment	45
Registration plate lamp issues	25
Horn not working \|1.6.2a\|	16
Exhaust emissions carbon monoxide content after 2nd fast idle excessive \|7.3.D.3\|	14
Brakes imbalanced across an axle	11
Nearside Rear Suspension component mounting prescribed area is excessively corroded \|2.4.A.3\|	9
Exhaust emissions Lambda reading after 2nd fast idle outside specified limits \|7.3.D.3\|	9
Nearside Front position lamp\|s\| not working \|1.1.A.3b\|	8
Rear brake binding	8
Exhaust emissions carbon monoxide content at idle excessive \|7.3.D.4\|	8
Offside Stop lamp not working \|1.2.1b\|	8
Offside Front position lamp\|s\| not working \|1.1.A.3b\|	8
Nearside Stop lamp not working \|1.2.1b\|	8
Offside Rear Direction indicator incorrect colour \|1.4.A.2f\|	7
Nearside Rear Suspension spring mounting prescribed area is excessively corroded \|2.4.A.3\|	6
Offside Rear Suspension spring mounting prescribed area is excessively corroded \|2.4.A.3\|	6
Front brake disc in such a condition that it is seriously weakened	6
Exhaust has a major leak of exhaust gases \|7.1.2\|	6
Nearside Front Direction indicator incorrect colour \|1.4.A.2f\|	6
Exhaust emissions hydrocarbon content after 2nd fast idle excessive \|7.3.D.3\|	6
Horn not working (7.7 (a))	6
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings \|6.1.B.2\|	5
Exhaust system not adequately supported \|7.1.1\|	5
Offside Rear Suspension component mounting prescribed area is excessively corroded \|2.4.A.3\|	5
Battery insecure \|1.9.1\|	5
Exhaust mounting missing \|7.1.1b\|	5
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))	5
Parking brake: efficiency below requirements \|3.7.B.7\|	4
Offside Front Direction indicator incorrect colour \|1.4.A.2f\|	4
Windscreen has damage	4
Offside Front Subframe mounting prescribed area is excessively corroded \|2.4.A.3\|	4
Hazard warning tell tale not working correctly \|1.4.B.1e\|	4
Nearside Rear Direction indicator incorrect colour \|1.4.A.2f\|	4
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings \|6.1.B.2\|	3
Rear Suspension spring mounting prescribed area is excessively corroded \|2.4.A.3\|	3
Nearside Headlamp not working on main beam \|1.7.5a\|	3
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings \|6.1.B.2\|	3
Nearside Side repeater not working \|1.4.A.2c\|	3
Rear Exhaust has a major leak of exhaust gases \|7.1.2\|	3
Offside Obligatory mirror seriously damaged, affecting the rear view \|8.1.2a\|	3
Rear parking brake recording little or no effort	3
Nearside Headlamp not working on dipped beam \|1.7.5a\|	3
Horn not loud enough to be heard by another road user \|1.6.2b\|	3
Offside Front Lower Suspension arm has excessive play in a ball joint \|2.4.G.2\|	3
Fuel system component leaking \|7.2.3\|	3
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))	3
Offside Front Service brake excessively binding (1.2.1 (f))	3
Offside Front Seat belt anchorage prescribed area is excessively corroded \|5.2.6\|	2
Nearside Suspension component mounting prescribed area is excessively corroded \|2.4.A.3\|	2
Offside Suspension component mounting prescribed area is excessively corroded \|2.4.A.3\|	2
Front Suspension component mounting prescribed area is excessively corroded \|2.4.A.3\|	2
Offside Front Shock absorber has a serious fluid leak \|2.7.3\|	2
Offside Front Suspension component mounting prescribed area is excessively corroded \|2.4.A.3\|	2
Offside Headlamp not working on main beam \|1.7.5a\|	2
Brake hose excessively deteriorated	2
Offside Headlamp not working on dipped beam \|1.7.5a\|	2
Offside Front Track rod end ball joint has excessive play \|2.2.B.1f\|	2
Offside Front Suspension spring mounting prescribed area is excessively corroded inner arch \|2.4.A.3\|	2
Registration plate issues	2
Offside Inner Front Suspension component mounting prescribed area is excessively corroded \|2.4.A.3\|	2
Offside Outer Rear Suspension spring mounting prescribed area is excessively corroded \|2.4.A.3\|	2
Nearside Rear Direction indicator not working \|1.4.A.2c\|	2
Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings \|6.1.B.2\|	2
Offside Rear Shock absorber has a serious fluid leak \|2.7.3\|	2
Offside Side repeater not working \|1.4.A.2c\|	2
Body has a sharp edge caused by damage \|6.1.C.1\|	2
Nearside Rear Direction indicators incorrect colour \|1.4.A.2f\|	2
Offside Rear Direction indicators incorrect colour \|1.4.A.2f\|	2
Offside Track rod end ball joint has excessive play \|2.2.B.1f\|	2
Nearside Front suspension has excessive play in a lower suspension ball joint \|2.5.B.1a\|	2
Offside front brake binding \|3.7.B.1\|	2
Exhaust emissions hydrocarbon content excessive \|7.3.B.1b\|	2
Nearside Rear Stop lamp not working \|1.2.1b\|	2
Front Exhaust system not adequately supported \|7.1.1\|	2
Offside Rear Rear fog lamp not working \|1.3.2b\|	2
Nearside Rear Suspension spring mounting prescribed area is excessively corroded inner sill \|2.4.A.3\|	2
Exhaust emits excessive smoke or vapour of any colour \|7.4.B.4\|	2
Nearside Inner Suspension component mounting prescribed area is excessively corroded \|2.4.A.3\|	2
Nearside Front Suspension component mounting prescribed area is excessively corroded \|2.4.A.3\|	2
Nearside Inner Rear Suspension spring mounting prescribed area is excessively corroded \|2.4.A.3\|	2
Offside Rear fog lamp not working \|1.3.2b\|	2
Emissions not tested \|7.3.A.1\|	2
Nearside Front Front position lamp\|s\| not working \|1.1.A.3b\|	2
Centre Exhaust has a major leak of exhaust gases \|7.1.2\|	2
Offside Rear Stop lamp not working \|1.2.1b\|	2
Mechanical brake component has restricted free movement	2
Rear Mechanical brake component has restricted free movement	2
Exhaust emits clearly visible black smoke during acceleration \|8.2.1.2 \|g\|\|	2
Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer`s specified limits \|8.2.1.2 \|a\|\|	2
Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturer`s specified limits \|8.2.1.2 \|a\|\|	2
Exhaust carbon monoxide content at idle exceeds manufacturer`s specified limits \|8.2.1.2 \|b\|\|	2
Exhaust Lambda reading after 2nd fast idle outside specified limits \|8.2.1.2 \|c\|\|	2
Windscreen washer not working	2
Horn not working (7.7 (a) (ii))	2
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))	2
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))	2
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))	2
Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))	2
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SPRING HANGER (5.3.6 (a) (i))	2
Exhaust has a major leak of exhaust gases (6.1.2 (a))	2
Nearside Front Direction indicator incorrect colour (4.4.3 (a))	2
Offside Front Direction indicator incorrect colour (4.4.3 (a))	2
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))	2
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i))	2
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i))	2
Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a))	2
Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))	2
Battery insecure and likely to fall from carrier (4.13 (a) (ii))	2
Offside Rear Service brake excessively binding (1.2.1 (f))	2
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i))	2
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings \|6.1.B.2\|	1
Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings \|6.1.B.2\|	1
Nearside Rear wheel bearing has excessive play \|2.6.2\|	1
Nearside Front Suspension spring mounting prescribed area is excessively corroded \|2.4.A.3\|	1
Offside Front Suspension spring mounting prescribed area is excessively corroded \|2.4.A.3\|	1
Nearside Front Seat belt anchorage prescribed area is excessively corroded \|5.2.6\|	1
Nearside Front Steering component mounting prescribed area is excessively corroded \|2.2.C.1h\|	1
Offside Front Steering component mounting prescribed area is excessively corroded \|2.2.C.1h\|	1
Nearside Windscreen wiper not operating automatically when switched on \|8.2.1b\|	1
Nearside Front Shock absorber has an excessively worn shock absorber pivot \|2.7.4\|	1
Driver`s door does not latch securely closed \|6.2.B.1a\|	1
Nearside Front Lower Suspension component mounting prescribed area is excessively corroded \|2.4.A.3\|	1
Front Exhaust mounting missing \|7.1.1b\|	1
Centre Exhaust system not adequately supported \|7.1.1\|	1
Nearside Rear wheel bearing rough when rotated \|2.6.1\|	1
Offside Rear wheel bearing rough when rotated \|2.6.1\|	1
Brake pedal anti-slip provision worn smooth \|3.3.A.1b\|	1
Nearside Body has a projection caused by damage \|6.1.C.1\|	1
Brake load sensing valve seized \|3.6.E.3\|	1
Nearside Front Subframe mounting prescribed area is excessively corroded inner arch \|2.4.A.3\|	1
Front position lamp\|s\| incorrect colour \|1.1.A.3e\|	1
Nearside Front Track rod end ball joint has excessive play \|2.2.B.1f\|	1
Nearside Seat belt anchorage prescribed area is excessively corroded \|5.2.6\|	1
Nearside Front Brake pipe leaking \|3.6.A.1\|	1
Offside front brake juddering severely \|3.7.A.2b\|	1
Offside Front brake disc excessively scored \|3.5.1h\|	1
Nearside Front Subframe mounting prescribed area is excessively corroded chassis leg \|2.4.A.3\|	1
Offside Front Headlamp aim beam image obviously incorrect \|1.8.A.1b\|	1
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings \|6.1.B.2\|	1
Offside Rear Rear position lamp\|s\| not working side light bulb inop \|1.1.A.3b\|	1
Offside Front Headlamp aim beam image obviously incorrect beam pattern blurry \|1.8.A.1b\|	1
Offside Front Headlamp excessively damaged so that the light output is severely reduced lens smashed \|1.7.5a\|	1
Offside Front Track rod end loose inner track rod has excessive play \|2.2.B.1d\|	1
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings corrosion hole in end of OS sill \|6.1.B.2\|	1
Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings corrosion holes within 30cm of front jacking points OS and NS \|6.1.B.2\|	1
Vehicle structure has excessive corrosion which adversely affects braking or steering corrosion hole in NSF wheel arch within 30cm of ABS pump mounting \|6.1.A.1\|	1
Nearside Rear Inner Suspension spring mounting prescribed area is excessively corroded cill \|2.4.A.3\|	1
Power steering pipe\|s\| or hose\|s\| fouling other parts of the vehicle \|2.3.2\|	1
Offside Inner Rear Suspension component mounting prescribed area is excessively corroded \|2.4.A.3\|	1
Offside Rear Brake cable has wires broken and is significantly weakened \|3.5.1b\|	1
Centre Exhaust mounting missing \|7.1.1b\|	1
Nearside Front Windscreen wiper blade deteriorated \|8.2.2\|	1
Offside Front Windscreen wiper blade deteriorated \|8.2.2\|	1
Offside Front Front wheel bearing has excessive play \|2.5.A.3c\|	1
Nearside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength \|5.3.6 \|a\| \|i\|\|	1
Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength \|5.3.6 \|a\| \|i\|\|	1
Nearside Front Shock absorber has a serious fluid leak \|2.7.3\|	1
Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt \|2.2.C.1c\|	1
Offside Front front brake binding \|3.7.B.1\|	1
Offside Front Direction indicator not working \|1.4.A.2c\|	1
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` \|8.3.1e\|	1
Offside Stop lamp emits other than a steady red light \|1.2.1e\|	1
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings \|6.1.B.2\|	1
Front Brake pipe excessively damaged \|3.6.B.2c\|	1
Nearside Rear Shock absorber has negligible damping effect \|2.7.5\|	1
Offside Obligatory mirror missing \|8.1.1\|	1
Offside Rear Body has a sharp edge caused by damage \|6.1.C.1\|	1
Nearside Rear Body has a sharp edge caused by damage \|6.1.C.1\|	1
Nearside Rear fog lamp emits a light other than red \|1.3.2e\|	1
Nearside Rear position lamp\|s\| incorrect colour \|1.1.A.3e\|	1
Stop lamp emits other than a steady red light \|1.2.1e\|	1
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing \|5.3.6 \|a\| \|i\|\|	1
Exhaust has part of the system excessively deteriorated \|7.1.1a\|	1
Offside Headlamps matched pair are incorrectly positioned \|1.7.3\|	1
Parking brake lever has no reserve travel \|3.1.6b\|	1
Nearside Front Direction indicator adversely affected by the operation of another lamp \|1.4.A.2h\|	1
Offside Rear Direction indicator adversely affected by the operation of another lamp \|1.4.A.2h\|	1
Front position lamp\|s\| adversely affected by the operation of another lamp \|1.1.A.3f\|	1
Offside Obligatory mirror does not provide a view to the rear \|8.1.2b\|	1
Offside Front position lamp\|s\| adversely affected by the operation of another lamp \|1.1.A.3f\|	1
Offside Headlamp excessively damaged so that the light output is severely reduced \|1.7.5a\|	1
Offside Direction indicator adversely affected by the operation of another lamp \|1.4.A.2h\|	1
Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings crossmember \|6.1.B.2\|	1
Exhaust emits visible black smoke at idle \|7.3.A.2b\|	1
Exhaust emissions carbon monoxide content excessive \|7.3.B.1a\|	1
Nearside Front Headlamp not working on dipped beam \|1.7.5a\|	1
Nearside Front Headlamp not working on main beam \|1.7.5a\|	1
Offside Rear fog lamp adversely affected by the operation of another lamp \|1.3.2f\|	1
Direction indicators not working \|1.4.A.2c\|	1
Hazard warning lamps not flashing in phase, with ignition on \|1.4.B.1f\|	1
Hazard warning lamps not flashing in phase, with ignition off \|1.4.B.1f\|	1
Bonnet retaining device ineffective \|8.4.2\|	1
Front brake application uneven	1
front brakes release unevenly \|3.7.B.4\|	1
Offside Headlamp not in good working order \|not working\| \|1.2.4a\|	1
Bonnet cannot be secured in the closed position \|8.4.1\|	1
Offside Front Stop lamp not working \|1.2.1b\|	1
Nearside Rear Rear wheel bearing has excessive play \|2.6.2\|	1
Nearside Headlamp not in good working order adversely affecting beam image \|1.2.4a\|	1
Offside Front constant velocity joint gaiter split \|2.5.C.1a\|	1
Nearside Body has a sharp edge caused by damage \|6.1.C.1\|	1
Offside Rear Headlamp not working on dipped beam \|1.7.5a\|	1
Rear Exhaust system not adequately supported \|7.1.1\|	1
Rear Exhaust has part of the system excessively deteriorated \|7.1.1a\|	1
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced \|6.1.1 \|c\| \|i\|\|	1
Service brake efficiency less than 50% of the required value \|1.2.2 \|a\| \|ii\|\|	1
Parking brake efficiency less than 50% of the required value \|1.4.2 \|a\| \|ii\|\|	1
Rear Stop lamp not working ALL \|1.2.1b\|	1
Nearside Inner Rear position lamp\|s\| not working \|1.1.A.3b\|	1
Offside Rear Wheel bearing rough when rotated \|5.1.3 \|b\| \|i\|\|	1
Nearside Rear Wheel bearing rough when rotated \|5.1.3 \|b\| \|i\|\|	1
Nearside Front Front suspension has excessive play in a lower suspension ball joint \|2.5.B.1a\|	1
Headlamp levelling device inoperative Switch faulty \|4.1.5 \|a\|\|	1
Offside Rear Brake hose bulging under pressure \|3.6.B.3\|	1
Offside Rear Suspension spring mounting prescribed area is excessively corroded sill / inner sill \|2.4.A.3\|	1
Offside Front Suspension spring mounting prescribed area is excessively corroded around jacking point \|2.4.A.3\|	1
Nearside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc \|2.5.C.1a\|	1
Nearside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc \|2.5.C.1a\|	1
Front Subframe mounting prescribed area is excessively corroded \|2.4.A.3\|	1
Offside Outer Suspension component mounting prescribed area is excessively corroded sill \|2.4.A.3\|	1
Offside Suspension component mounting prescribed area is excessively corroded center outrigger \|2.4.A.3\|	1
Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt \|2.4.G.2\|	1
Offside Inner Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc \|2.5.C.1a\|	1
Offside Inner Suspension component mounting prescribed area is excessively corroded \|2.4.A.3\|	1
Nearside Front Upper Steering system excessively tight \|2.2.D.1\|	1
Offside Rear brake drum contaminated by brake fluid \|3.5.1h\|	1
Offside Rear Service brake indicates brake bind \|3.7.D.2a\|	1
Nearside Obligatory mirror seriously damaged, affecting the rear view \|8.1.2a\|	1
Offside Rear position lamp\|s\| adversely affected by the operation of another lamp \|1.1.A.3f\|	1
Exhaust emits an excessive level of metered smoke for a turbo charged engine \|7.4.B.3b\|	1
Nearside Front Lower Suspension arm has excessive play in a ball joint \|2.4.G.2\|	1
Nearside Outer Front constant velocity joint gaiter split \|2.5.C.1a\|	1
Offside Windscreen wiper not operating over a large enough area to give an adequate view \|8.2.1c\|	1
Offside Headlamp not in good working order adversely affecting beam image \|1.2.4a\|	1
Rear position lamp\|s\| excessively deteriorated so that it is not visible from a reasonable distance \|1.1.A.3d\|	1
Offside Rear Subframe mounting prescribed area is excessively corroded \|2.4.A.3\|	1
Centre Exhaust has a major leak of exhaust gases silencer box \|7.1.2\|	1
Front position lamp\|s\| not working \|1.1.A.3b\|	1
Spare wheel insecure \|6.4.2\|	1
Offside Front suspension has excessive play in a lower suspension ball joint \|2.5.B.1a\|	1
Nearside Front wheel bearing has excessive play \|2.5.A.3c\|	1
Nearside Vehicle structure excessively corroded within 30cm of towbar mounting \|6.6.6\|	1
Offside Vehicle structure excessively corroded within 30cm of towbar mounting \|6.6.6\|	1
Front Body has a sharp edge caused by damage \|6.1.C.1\|	1
Front Direction indicators incorrect colour \|1.4.A.2f\|	1
Rear Direction indicators incorrect colour \|1.4.A.2f\|	1
Seat belt locking mechanism does not secure or release \|5.2.5a\|	1
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill. \|5.3.6 \|a\| \|i\|\|	1
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill \|2.4.A.3\|	1
Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting \|6.6.6\|	1
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting \|6.6.6\|	1
Offside Front Subframe mounting prescribed area is excessively corroded next to jacking point \|2.4.A.3\|	1
Offside Rear Suspension spring mounting prescribed area is excessively corroded leaf spring mount \|2.4.A.3\|	1
Nearside Rear Suspension spring mounting prescribed area is excessively corroded leaf spring mount \|2.4.A.3\|	1
Offside Front Subframe mounting prescribed area is excessively corroded inner wheel arch \|2.4.A.3\|	1
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch,shock absorber mount \|2.4.A.3\|	1
Offside Front Suspension component mounting prescribed area is excessively corroded Macpherson strut upper mounting turret \|2.4.A.3\|	1
Exhaust has a major leak of exhaust gases centre box \|7.1.2\|	1
Rear brake application uneven	1
Offside Rear rear brake recording little or no effort \|3.7.B.5a\|	1
Nearside Stop lamp excessively damaged so that it is not visible from a reasonable distance \|1.2.1d\|	1
Exhaust has a major leak of exhaust gases rear box \|6.1.2 \|a\|\|	1
Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Radiator support crossmember \|6.1.B.2\|	1
Brake performance not tested \|3.7.A.1\|	1
Offside Rear An item not tested \|Manual\|	1
Service brake: efficiency below requirements \|3.7.B.7\|	1
Nearside Front Ball joint has excessive play \|2.2.B.1f\|	1
Offside Front Ball joint has excessive play \|2.2.B.1f\|	1
Centre Rear Exhaust mounting missing \|7.1.1b\|	1
Power steering pump drive system defective \|2.3.6\|	1
Nearside Front Subframe mounting prescribed area is excessively corroded \|2.4.A.3\|	1
Nearside Front Macpherson strut upper support bearing is stiff in operation \|2.5.B.1b\|	1
Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch \|6.1.1 \|c\| \|i\|\|	1
Nearside Front Position lamp not working \|4.2.1 \|a\|\|	1
Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill \|6.1.B.2\|	1
Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill \|6.1.B.2\|	1
Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill \|6.1.B.2\|	1
Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill \|6.1.B.2\|	1
Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings flitch \|6.1.B.2\|	1
Offside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings \|6.1.B.2\|	1
Nearside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings \|6.1.B.2\|	1
Offside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings \|6.1.B.2\|	1
Nearside Front Suspension arm has excessive play in a ball joint \|2.4.G.2\|	1
Nearside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings \|6.1.B.2\|	1
Offside Inner Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings \|6.1.B.2\|	1
Offside Rear position lamp\|s\| incomplete \|1.1.4a\|	1
Rear fog lamp tell tale not working \|1.3.1b\|	1
Stop lamp not working \|1.2.1b\|	1
Windscreen wiper blade deteriorated \|8.2.2\|	1
Nearside Front brake disc excessively pitted \|3.5.1h\|	1
Offside Front brake disc excessively pitted \|3.5.1h\|	1
Fuel cap/sealing device missing \|7.2.4a\|	1
Rear Stop lamp not working \|1.2.1b\|	1
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits \|8.2.1.2 \|b\|\|	1
Exhaust carbon monoxide content at idle exceeds default limits \|8.2.1.2 \|b\|\|	1
Exhaust hydrocarbon content after 2nd fast idle exceeds default limits \|8.2.1.2 \|b\|\|	1
Offside Rear Suspension spring mounting prescribed area is excessively corroded outer sill \|2.4.A.3\|	1
Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded \|2.4.A.3\|	1
Nearside Front Lower Ball joint has excessive play \|2.2.B.1f\|	1
Nearside Front Lower Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt \|2.2.C.1c\|	1
Front Integral body structure is fractured and structural rigidity is significantly reduced Both sides under wings as marked areas (6.1.1 (a) (i))	1
Emissions not tested due to miss fire and uneven running (8.2.1.2 (d))	1
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear of spring, inner sill (5.3.6 (a) (i))	1
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front of spring, out rigger (5.3.6 (a) (i))	1
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear of spring, inner sill (5.3.6 (a) (i))	1
Exhaust has a major leak of exhaust gases Cat/silencer joint blowing (6.1.2 (a))	1
Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i))	1
Offside Front Brake pipe likely to become detached or damaged (1.1.11 (d) (ii))	1
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b))	1
Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b))	1
Offside Side repeater not working (4.4.1 (a) (ii))	1
Nearside Rear Direction indicator not working (4.4.1 (a) (ii))	1
Nearside Front Suspension arm insecure and impairing directional stability (5.3.3 (a) (ii))	1
Front Sub-frame corroded and seriously weakened (5.3.3 (b) (i))	1
Nearside Front Brake hose excessively damaged (1.1.12 (b) (ii))	1
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i))	1
Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both rear spring mounting areas (5.3.6 (a) (i))	1
Emissions not tested due to engine temp getting high (8.2.1.2 (d))	1
Brake performance not tested due to nsf suspension arm (1.2.1 (g))	1
Emissions not tested engine misfiring (8.2.1.2 (d))	1
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced door step (7.1.1 (a) (i))	1
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))	1
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper inner arch (5.3.6 (a) (i))	1
Nearside Front Service brake excessively binding (1.2.1 (f))	1
Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL INNER (6.2.2 (d) (i))	1
Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL INNER AND OUTER (6.2.2 (d) (i))	1
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength SPRING HANGER (5.3.6 (a) (i))	1
Nearside Front Suspension arm ball joint likely to become detached BOLT MISSING (5.3.4 (a) (ii))	1
Brake hydraulic reservoir fluid level significantly below minimum level (1.1.10 (d) (ii))	1
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i))	1
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i))	1
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))	1
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii))	1
Front Service brake excessively fluctuating (1.2.1 (e))	1
Emissions not tested (8.2.1.2 (d))	1
Offside Rear Position lamp light intensity significantly reduced (4.2.3 (a) (ii))	1
Brake load sensing valve inoperative and ABS not fitted or inoperative (1.1.17 (c) (ii))	1
Nearside Front Brake prescribed area is excessively corroded inner wing adjacent to brake pipe mounts (1.1.21 (e) (i))	1
Offside Front Service brake excessively fluctuating (1.2.1 (e))	1
Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))	1
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front lateral cross member mount area (5.3.6 (a) (i))	1
Offside Front All direction indicators not working (4.4.1 (a) (ii))	1
Offside Rear Inner Brake pipe leaking on a hydraulic braking system brake union to wheel cylinder leaking (1.1.11 (b) (ii))	1
Brake performance not tested due to leak & condition of brake pipes (1.2.1 (g))	1
Main beam tell-tale not working (4.9.1 (a) (ii))	1
Nearside Rear Shock absorbers has negligible damping effect (5.3.2 (d))	1
Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d))	1
Nearside Side repeater not working (4.4.1 (a) (ii))	1
Nearside Rear Body component damaged and likely to cause injury light lens (6.2.1 (a) (i))	1
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i))	1
Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))	1
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced step area (7.1.1 (a) (i))	1
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i))	1
Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))	1
Offside Stop lamp(s) not working (4.3.1 (a) (ii))	1
Offside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a))	1
Central Exhaust has a major leak of exhaust gases (6.1.2 (a))	1
Nearside Front Integral body structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii))	1
Nearside Front Shock absorbers has a serious fluid leak	1
Offside Front Integral body structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii))	1
Nearside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i))	1
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger ect (5.3.6 (a) (i))	1
Fuel cap/sealing device ineffective (6.1.3 (b) (i))	1
Supplementary restraint system warning lamp indicates a fault (7.1.6 (a))	1
Rear Seat belt missing buckles (7.1.2 (a))	1
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))	1
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))	1
Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))	1
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch by strut (5.3.6 (a) (i))	1
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength step (5.3.6 (a) (i))	1
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i))	1
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear of inner arch (5.3.6 (a) (i))	1
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill rear corner (5.3.6 (a) (i))	1
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Shocker mounting (5.3.6 (a) (i))	1
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Shocker mounting (5.3.6 (a) (i))	1
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Jacking point (5.3.6 (a) (i))	1
Offside Front Wheel bearing has excessive play (5.1.3 (a) (i))	1
Nearside Front Steering system excessively rough Shocker top (2.1.1 (a))	1
Offside Front Steering system excessively rough Shocker top (2.1.1 (a))	1
Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength front hanger - out rigger/inner sill (5.3.6 (a) (i))	1
Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength rear hanger - rear panel (5.3.6 (a) (i))	1
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b))	1
Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b))	1
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))	1
Nearside Headlamp not working on main beam (4.1.1 (a) (ii))	1
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill(jacking point) (5.3.6 (a) (i))	1
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (jacking point) (5.3.6 (a) (i))	1
Offside Front Inner Parking brake mechanism/associated mounting prescribed area is excessively corroded sill/step (1.1.21 (e) (i))	1
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shock mount wheel arch (5.3.6 (a) (i))	1
Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i))	1
Offside Front Position lamp not working (4.2.1 (a) (ii))	1
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))	1
Offside Headlamp not working on main beam (4.1.1 (a) (ii))	1
Headlamp levelling device inoperative (4.1.5 (a))	1
Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))	1
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))	1
Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear valance both sides (5.3.6 (a) (i))	1
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength next to jacking point (5.3.6 (a) (i))	1
Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))	1
Nearside Front Inner Brake pipe at imminent risk of failure or fracture (1.1.11 (a))	1
Nearside Front Outer Brake pipe at imminent risk of failure or fracture (1.1.11 (a))	1
Nearside Front Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii))	1
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i))	1
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength back pannel (5.3.6 (a) (i))	1
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength back pannel (5.3.6 (a) (i))	1
Offside Front Macpherson strut mounting damaged and seriously weakened (5.3.3 (b) (i))	1
Nearside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i))	1
Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i))	1
Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i))	1
Offside Rear Position lamp not working (4.2.1 (a) (ii))	1
Offside Front Lower Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting corrosion/holed (6.2.2 (d) (i))	1
Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis rust by jacking point.holed (6.2.2 (d) (i))	1
Exhaust system insecure 6 exhaust rubbers required (6.1.2 (a))	1

We get to these numbers by trawling through over 1 billion MOT test results since 2004 and crunched the numbers. We remove anything to do with Tyres, as they are model independent and group together common non-model specific issues. We are trying to get to a picture of what models have what issues.

Please note: We take the data from the DVSA. This data is raw and can contain typos and spelling mistakes that garages may have entered while recording a MOT result. Specifically miss-match on names of models and makes. We are constantly cleaning the data so bear with the odd issue.

Got suggestions? We’re improving this section all the time. If you have any suggestions, please let us know.

MOT History from tests of petrol FIAT DUCATOs year 2000

Find us on Facebook