| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 79 |
| Windscreen wiper does not clear the windscreen effectively | 61 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 44 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 40 |
| Headlamp aim out of alignment | 34 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 26 |
| Registration plate lamp issues | 21 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 19 |
| Brakes imbalanced across an axle | 13 |
| Horn not working |1.6.2a| | 12 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
| Brake hose excessively deteriorated | 9 |
| Registration plate issues | 9 |
| Parking brake: efficiency below requirements |3.7.B.7| | 8 |
| Service brake: efficiency below requirements |3.7.B.7| | 7 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 7 |
| Rear brake binding | 7 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 7 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 7 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Parking brake lever has no reserve travel |3.1.6b| | 5 |
| Offside Stop lamp not working |1.2.1b| | 5 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 5 |
| Exhaust system not adequately supported |7.1.1| | 5 |
| Battery insecure |1.9.1| | 5 |
| Nearside Side repeater not working |1.4.A.2c| | 4 |
| Nearside Stop lamp not working |1.2.1b| | 4 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 4 |
| Front brake disc in such a condition that it is seriously weakened | 4 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Side repeater not working |1.4.A.2c| | 4 |
| Windscreen washer not working | 4 |
| Horn not working (7.7 (a)) | 4 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 3 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 3 |
| Exhaust system insecure |6.1.2 |a|| | 3 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 3 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 3 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 3 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 3 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Brake load sensing valve linkage seized |3.6.E.3| | 3 |
| Emissions not tested |7.0| | 3 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 3 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 3 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 3 |
| Horn not working (7.7 (a) (ii)) | 3 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 3 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 3 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Front brake excessively fluctuating | 2 |
| Nearside Rear Brake valve leaking |3.6.A.1| | 2 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Brake performance not tested |3.7.A.1| | 2 |
| Front passenger seat insecure |6.2.3| | 2 |
| Rear fog lamp tell tale not working |1.3.1b| | 2 |
| Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 2 |
| Exhaust carbon monoxide content at idle exceeds default limits |8.2.1.2 |b|| | 2 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 2 |
| Offside Front Braking system leaking |3.6.A.1| | 2 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Rear brake application uneven | 2 |
| Offside front brake binding |3.7.B.1| | 2 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Rear Rear fog lamp not working |1.3.2b| | 2 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 2 |
| Centre Exhaust system not adequately supported |7.1.1| | 2 |
| Hazard warning switch faulty |1.4.B.1d| | 2 |
| Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Fuel cap/sealing device sealing washer missing |7.2.4c| | 2 |
| Exhaust carbon monoxide content at idle exceeds manufacturer`s specified limits |8.2.1.2 |b|| | 2 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturer`s specified limits |8.2.1.2 |a|| | 2 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Steering column movement between the shaft and steering wheel |2.1.2b| | 2 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 2 |
| Nearside Front Brake pipe leaking |3.6.A.1| | 2 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Nearside Rear Wheel bearing has excessive play |5.1.3 |a| |i|| | 2 |
| Hazard warning switch inoperative |4.4.2 |a| |ii|| | 2 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 2 |
| Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 2 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Hazard warning switch inoperative (4.4.2 (a) (ii)) | 2 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 2 |
| Offside Front Seat belt not functioning as intended (7.1.2 (c)) | 2 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 2 |
| Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 2 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 2 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 2 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 2 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases centre and rear exhaust |6.1.2 |a|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail |5.3.6 |a| |i|| | 1 |
| Oil leaking excessively from engine |8.4.1 |a| |i|| | 1 |
| Emissions not tested due to major leaks on exhaust |8.2.1.2 |d|| | 1 |
| Nearside Outer Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Nearside Rear Inner Suspension spring mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Inner Suspension spring mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Brake load sensing valve seized |3.6.E.3| | 1 |
| Offside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Front Brake hose leaking |3.6.A.1| | 1 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Braking system leaking |3.6.A.1| | 1 |
| Offside Headlamp insecure |1.7.3| | 1 |
| Offside Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Nearside Front passenger seat insecure |6.2.3| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Rear fog lamp not working |1.3.2b| | 1 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Rear Brake valve has an excessive discharge of oil |3.6.E.1| | 1 |
| Emissions not tested |8.2.1.2 |d|| | 1 |
| Brake valve has an excessive discharge of oil |3.6.E.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Rear Seat belt flexible stalk cable has broken strands |5.2.4b| | 1 |
| Nearside Front brake disc excessively scored |3.5.1h| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Front Brake pipe leaking |3.6.A.1| | 1 |
| Offside Upper Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Central Front Brake pipe leaking |3.6.A.1| | 1 |
| Parking brake lever has no reserve travel linkage siezed |3.1.6b| | 1 |
| Brake servo inoperative |1.1.10 |a| |ii|| | 1 |
| Nearside front brake recording little or no effort |3.7.B.5a| | 1 |
| Offside front brake recording little or no effort |3.7.B.5a| | 1 |
| Driver`s door catch deteriorated so the door cannot be readily opened or closed |6.2.B.2| | 1 |
| Steering system excessively rough |2.2.D.1| | 1 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Windscreen wiper blade insecure | 1 |
| Horn not a continuous or uniform sound |1.6.2e| | 1 |
| Offside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Brake hydraulic reservoir cap missing |3.6.G.1a| | 1 |
| Centre Exhaust mounting missing |7.1.1b| | 1 |
| Front Bonnet cannot be secured in the closed position |8.4.1| | 1 |
| Brake cable has restricted free movement |3.5.1k| | 1 |
| Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 1 |
| Rear parking brake recording little or no effort | 1 |
| Windscreen has damage | 1 |
| Exhaust mounting missing |7.1.1b| | 1 |
| Offside Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Front Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Direction indicator incorrect colour |4.4.3 |a|| | 1 |
| Offside Front Direction indicator incorrect colour |4.4.3 |a|| | 1 |
| Nearside Rear Direction indicator incorrect colour |4.4.3 |a|| | 1 |
| Nearside Rear Upper Position lamp light intensity significantly reduced |4.2.3 |a| |ii|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member |6.1.1 |c| |i|| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outriger |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outriger |6.1.B.2| | 1 |
| Rear Exhaust mounting missing |7.1.1b| | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Towbar retaining device missing |6.6.3a| | 1 |
| Stop lamp not working |1.2.1b| | 1 |
| Nearside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Outer Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Brake pipe seriously damaged |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Offside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Nearside Inner Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Parking brake lever is impeded in its travel |3.1.6c| | 1 |
| An item not tested |Manual| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Central Exhaust emissions likely to be affected by an exhaust leak |8.2.2.1 |b|| | 1 |
| Nearside Front Passenger`s seat insecure bolt loose |6.2.A.1| | 1 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Offside Upper Front position lamp|s| not working |1.1.A.3b| | 1 |
| Power steering malfunctioning |2.3.3a| | 1 |
| Windscreen washer control missing |8.2.1a| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength by strut mountin |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wing |5.3.6 |a| |i|| | 1 |
| Nearside Front Position lamp not working |4.2.1 |a|| | 1 |
| Offside Front Electrical wiring insecure and connectors likely to become disconnected |4.11 |a| |ii|| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded under wing |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded before and after wheel |2.4.A.3| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded shackle area |2.4.A.3| | 1 |
| Rear Suspension component mounting prescribed area is excessively corroded panel |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded shackle area |2.4.A.3| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch area and turret area |2.4.A.3| | 1 |
| Nearside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Inner Steering arm has relative movement at its fixings rack joint |2.2.B.1h| | 1 |
| Nearside Front Inner Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Inner Front constant velocity joint is insecure spraying grease |2.5.C.1b| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded x2 |2.4.A.3| | 1 |
| Offside Steering rack gaiter split |2.2.D.2d| | 1 |
| Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Power steering pipe/hose leaking Pipe at pump |2.1.5 |a|| | 1 |
| Emissions not tested EXHAUST BROKEN HOLED |8.2.1.2 |d|| | 1 |
| Front Brake relay lever has restricted free movement HANDBRAKE |1.1.15 |e|| | 1 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Nearside Rear position lamp|s| insecure |1.1.A.3a| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Nearside Rear Upper Outline marker lamp not working |4.2.1 |a|| | 1 |
| Offside Rear Upper Outline marker lamp not working |4.2.1 |a|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill next to spring mounting |5.3.6 |a| |i|| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill holed midway along vehicle |5.3.6 |a| |i|| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive 12 % |7.3.D.3| | 1 |
| Nearside Rear Inner Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Outer Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Headlamp does not operate immediately when selected on main beam |1.7.4a| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Centre Statutory seat belt missing |5.1.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 1 |
| Nearside Rear Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Nearside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded jacking point |2.4.A.3| | 1 |
| Nearside Rear Brake pipe leaking |3.6.A.1| | 1 |
| Nearside Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 1 |
| Nearside Rear Statutory seat belt missing |5.1.1| | 1 |
| Nearside Rear Leaf spring anchor bracket bolt missing |2.4.B.6c| | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Direction indicators not working |1.4.A.2c| | 1 |
| Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Nearside Rear Brake cable locking device insecure |3.5.1l| | 1 |
| Brake pedal anti-slip provision worn smooth |3.3.A.1b| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Suspension arm locating pin retaining device not properly locked |2.4.G.3b| | 1 |
| Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
| Nearside Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded sideframe |2.4.A.3| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded inner wing area |2.4.A.3| | 1 |
| Front brake application uneven | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Rear Leaf spring to axle fixing bolt insecure U bolt |5.3.1 |a| |i|| | 1 |
| Nearside Rear Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
| Nearside Front Suspension arm pin or bush excessively worn forward bush |5.3.4 |a| |i|| | 1 |
| Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded jacking point |2.4.A.3| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded inner step |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded inner step |5.2.6| | 1 |
| Speedometer clearly inoperative |6.7.2| | 1 |
| Rear Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Nearside Obligatory mirror insecure |3.3 |b| |ii|| | 1 |
| Offside Obligatory mirror insecure |8.1.1| | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Obligatory mirror missing |8.1.1| | 1 |
| Nearside Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Power steering pump drive system defective |2.3.6| | 1 |
| Horn not working |7.7 |a| |ii|| | 1 |
| Nearside Front Headlamp light intensity severely reduced |4.1.4 |a|| | 1 |
| Offside Front Stop lamp not working |1.2.1b| | 1 |
| Windscreen in an unacceptable condition |3.2 |c| |i|| | 1 |
| Other passenger door catch missing |6.2.3 |c| |ii|| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings jacking point |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings jacking point |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings by leaf spring |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings by leaf spring |6.1.B.2| | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Offside Front Power steering component|s| leaking |2.3.3b| | 1 |
| Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Offside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Brake linkage excessively worn and seriously weakened |3.5.1e| | 1 |
| Front brake disc excessively pitted |3.5.1h| | 1 |
| Front Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Nearside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill and inner arch |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
| Offside Rear Bumper insecure |6.1.4 |a| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Near front cross member |6.1.1 |c| |i|| | 1 |
| Steering system excessively rough |2.1.1 |a|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch and jacking point |6.2.2 |d| |i|| | 1 |
| Nearside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner sill |6.2.2 |d| |i|| | 1 |
| Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Under rear doors near rear spring hanger/toebar |6.2.2 |d| |i|| | 1 |
| Exhaust system not adequately supported fitted 3x rubber supports |7.1.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Jacking point |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cross memebr |6.1.B.2| | 1 |
| Nearside Body has a sharp edge caused by corrosion sill |6.1.C.1| | 1 |
| Offside Body has a sharp edge caused by corrosion sill |6.1.C.1| | 1 |
| Nearside Front Suspension arm has excessive play in a pin/bush rear wishbone bush |2.4.G.2| | 1 |
| Offside Front Suspension arm has excessive play in a pin/bush rear wishbone bush |2.4.G.2| | 1 |
| Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Rear Upper Shock absorber insecure |2.7.2b| | 1 |
| Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Obligatory mirror insecure |8.1.1| | 1 |
| Nearside Front Suspension arm rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 1 |
| Hazard warning switch inoperative broken (4.4.2 (a) (ii)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Exhaust system insecure rubber mounts were missing (6.1.2 (a)) | 1 |
| Towbar component defective drop plate bent (6.1.6 (a)) | 1 |
| Towbar component defective rear tow ball mount plate 2 bolts missing (6.1.6 (a)) | 1 |
| Offside Front Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment Cable snapped on test (1.1.6 (c)) | 1 |
| Windscreen wiper not working (3.4 (a)) | 1 |
| Nearside Rear Seat belt missing (7.1.2 (a)) | 1 |
| Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s and n/s inner wings (5.3.6 (a) (i)) | 1 |
| Fuel cap/sealing device missing (6.1.3 (b) (i)) | 1 |
| Front Body component corroded and likely to cause injury cross member (6.2.1 (a) (i)) | 1 |
| Nearside Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
| Offside Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
| Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Offside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced out rigger (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inc radiator carrier area (6.1.1 (c) (i)) | 1 |
| Offside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 1 |
| Front Integral body structure is fractured and structural rigidity is significantly reduced Front crossmember corroded and holed (6.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength NEAR CROSS MEMBER (5.3.6 (a) (i)) | 1 |
| Nearside Sub-frame corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Rear Brake valve leaking (1.1.7 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Shock absorber mounting area (5.3.6 (a) (i)) | 1 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Spare wheel insecure in carrier (6.1.5 (b) (i)) | 1 |
| Front Headlamp levelling device inoperative both (4.1.5 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing around battery carrier (5.3.6 (a) (i)) | 1 |
| Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength NEAR SIDE FRONT INNER WING / AND FRONT JACKING POINTS ALL MARK UP (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OFFSIDE FRONT INNER WING ALL MAK UP (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt retracting mechanism defective (7.1.2 (e)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Emissions not tested VEHICLE KEEPS CUTTING OUT (8.2.1.2 (d)) | 1 |
| Brake performance not tested due to corroded brake pipes (1.2.1 (g)) | 1 |
| Nearside Rear Other passenger door cannot be opened from outside the vehicle Sliding door handle broken. (6.2.3 (a)) | 1 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Wing near gearbox mounting excessively corroded. (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Brake master cylinder/servo mounting prescribed area is excessively corroded Wing within 30cm of servo. (1.1.21 (e) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Within 30cm of shock absorber mounting (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Leaf spring mount. (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Leaf spring mount. (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rear subframe mount. (5.3.6 (a) (i)) | 1 |
| Nearside Rear Position lamp with a multiple light source more than 1/2 not functioning (4.2.1 (a) (ii)) | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Outer Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Headlamp levelling device inoperative both (4.1.5 (a)) | 1 |
| Fuel system component leaking excessively or a risk of fire near fuel filter (6.1.3 (b) (ii)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Central Inner Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Brake servo defective or ineffective (1.1.10 (a) (i)) | 1 |
| Emissions not tested major ex leak (8.2.1.2 (d)) | 1 |
| Offside Front Suspension component pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Brake cable guide defective and affecting operation parking brake mounts (1.1.15 (d)) | 1 |
| Offside Front Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wing (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure inadequately repaired such that structural rigidity is significantly reduced inner sill (6.1.1 (d) (i)) | 1 |
| Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced panel (6.1.1 (d) (i)) | 1 |
| Nearside Integral body structure inadequately repaired such that structural rigidity is significantly reduced sill (6.1.1 (d) (i)) | 1 |
| Offside Rear Shock absorbers has a serious fluid leak | 1 |
| Nearside Rear Vehicle structure is deformed and structural rigidity is significantly reduced outriger (6.1.1 (a) (i)) | 1 |
| Nearside Inner Vehicle structure is deformed and structural rigidity is significantly reduced center sill (6.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure is deformed and structural rigidity is significantly reduced outriger (6.1.1 (a) (i)) | 1 |
| Offside Front Vehicle structure is deformed and structural rigidity is significantly reduced outriger (6.1.1 (a) (i)) | 1 |
| Offside Vehicle structure is deformed and structural rigidity is significantly reduced center sill times 2 (6.1.1 (a) (i)) | 1 |
| Fuel system component leaking at fuel filter (6.1.3 (b) (i)) | 1 |
| Brake performance unable to be tested blown brake pipe (1.2.1 (g)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed over heated (8.2.1.2 (d)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Brake hydraulic reservoir cap missing (1.1.10 (e)) | 1 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced engine mount prescribed area (6.1.1 (c) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Emissions unable to be completed exhaust leak (8.2.1.2 (d)) | 1 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength behind wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inside upper wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Front Lower Brake hose excessively damaged 2 cuts in hose to braid (1.1.12 (b) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength behind wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Direction indicator adversely affected by the operation of another lamp (4.4.3 (b)) | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength battery area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill holed (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sub-frame mounting holed (5.3.6 (a) (i)) | 1 |