| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 46 |
| Headlamp aim out of alignment | 30 |
| Windscreen wiper does not clear the windscreen effectively | 24 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 24 |
| Registration plate lamp issues | 23 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 16 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 15 |
| Parking brake: efficiency below requirements |3.7.B.7| | 12 |
| Horn not working |1.6.2a| | 9 |
| Rear parking brake recording little or no effort | 9 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 9 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 9 |
| Exhaust system not adequately supported |7.1.1| | 8 |
| Brakes imbalanced across an axle | 8 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 7 |
| Emissions not tested |7.0| | 7 |
| Registration plate issues | 6 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 6 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Offside Stop lamp not working |1.2.1b| | 5 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Service brake: efficiency below requirements |3.7.B.7| | 5 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 5 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 5 |
| Offside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 4 |
| Hazard warning switch faulty |1.4.B.1d| | 4 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 4 |
| Battery insecure |1.9.1| | 4 |
| Rear brake binding | 4 |
| Exhaust mounting missing |7.1.1b| | 4 |
| Nearside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 3 |
| Brake hose excessively deteriorated | 3 |
| Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 3 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 3 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 3 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Centre Exhaust system not adequately supported |7.1.1| | 3 |
| Offside Side repeater not working |1.4.A.2c| | 3 |
| Windscreen has damage | 3 |
| Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 3 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 3 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 3 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 2 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Front front brake binding |3.7.B.1| | 2 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 2 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Offside Rear fog lamp not working |1.3.2b| | 2 |
| Nearside Headlamp not working on main beam |1.7.5a| | 2 |
| Nearside Rear Stop lamp not working |1.2.1b| | 2 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Driver`s seat insecure |6.2.A.1| | 2 |
| Parking brake lever has no reserve travel |3.1.6b| | 2 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 2 |
| Offside Outer Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Outer Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Steering system excessively rough |2.2.D.1| | 2 |
| Offside Front An item not tested |Manual| | 2 |
| Direction indicators not working |1.4.A.2c| | 2 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 2 |
| Nearside Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 2 |
| Offside Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 2 |
| Rear Exhaust system not adequately supported |7.1.1| | 2 |
| Offside Front Brake pipe leaking |3.6.A.1| | 2 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 2 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Rear Brake load sensing valve seized |3.6.E.3| | 2 |
| Brake performance not tested |3.7.A.1| | 2 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Nearside Stop lamp not working |1.2.1b| | 2 |
| Spare wheel carrier insecure |6.4.2| | 2 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 2 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Steering column universal joint has excessive play |2.1.5| | 2 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 2 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 2 |
| Horn sound not in accordance with requirements (7.7 (c)) | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 2 |
| Offside Front Service brake excessively fluctuating (1.2.1 (e)) | 2 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Rear Valve stem seriously damaged |4.1.D.1e| | 1 |
| Offside Rear Valve stem seriously damaged |4.1.D.1e| | 1 |
| Front Exhaust mounting missing |7.1.1b| | 1 |
| Offside Rear position lamp|s| incomplete |1.1.4a| | 1 |
| Offside Steering rack gaiter split |2.2.D.2d| | 1 |
| Front brake disc excessively scored |3.5.1h| | 1 |
| Front brake disc excessively pitted |3.5.1h| | 1 |
| Front brake application uneven | 1 |
| Brake pedal anti-slip provision worn smooth |3.3.A.1b| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Rear reflector excessively damaged so that its function is impaired |1.5.1c| | 1 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Nearside Front Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Front Inner Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Offside Rear Inner Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Stop lamp has less than 50% of the light sources illuminating |1.2.1b| | 1 |
| Steering rack insecure |2.2.B.1a| | 1 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.D.1| | 1 |
| Nearside Rear Statutory seat belt missing |5.1.1| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| Nearside Headlamp insecure |1.7.3| | 1 |
| Nearside Front Passenger`s seat insecure |6.2.A.1| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Front Additional braking device damaged |3.6.I.1| | 1 |
| Nearside Front Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Exhaust has a part missing |7.1.1a| | 1 |
| Offside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Centre Rear Seat belt stitching not secure |5.2.2b| | 1 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Brake load sensing valve seized and ABS not fitted or inoperative |1.1.17 |c| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength top strut mounting |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength leaf spring hanger mount |5.3.6 |a| |i|| | 1 |
| Rear Bumper likely to become detached |6.1.4 |a| |ii|| | 1 |
| Offside Rear Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced chassis out rigger |6.1.1 |b| |ii|| | 1 |
| Nearside Rear Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced chassis out rigger |6.1.1 |b| |ii|| | 1 |
| Nearside Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting cill |6.2.2 |d| |i|| | 1 |
| Offside Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting cill |6.2.2 |d| |i|| | 1 |
| Nearside Outer Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Outer Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Front Side repeater not working |1.4.A.2c| | 1 |
| Nearside Front Ball joint has excessive play |2.2.B.1f| | 1 |
| Rear Exhaust system insecure |6.1.2 |a|| | 1 |
| Nearside Rear Rear position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 1 |
| Fuel hose leaking |7.2.3| | 1 |
| Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Windscreen washer not working | 1 |
| Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 1 |
| Emissions not tested |8.2.1.2 |d|| | 1 |
| Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Exhaust system insecure |6.1.2 |a|| | 1 |
| Exhaust fumes entering cabin |6.1.2 |b| |i|| | 1 |
| Exhaust silencer insecure |8.1.1 |b| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
| Upper Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
| Offside Rear Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Offside Front Inner Suspension spring mounting prescribed area is excessively corroded wing under battery tray |2.4.A.3| | 1 |
| Nearside Upper Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Battery insecure |1.9.1| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded jack point |5.2.6| | 1 |
| Offside Rear Inner Suspension spring mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded sill end |2.4.A.3| | 1 |
| Nearside Rear Inner Suspension spring mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded sill end |2.4.A.3| | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area is excessively corroded wing |5.2.6| | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area is excessively corroded jack point |5.2.6| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded cross member |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded cross member |2.4.A.3| | 1 |
| Offside Front Inner Suspension spring mounting prescribed area is excessively corroded arch |2.4.A.3| | 1 |
| Offside Front Inner Suspension spring mounting prescribed area is excessively corroded wing strut top |2.4.A.3| | 1 |
| Nearside Front Side repeater not working |1.4.A.2c| | 1 |
| Nearside Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
| Offside Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Trailer electrical socket |13 pin| not operating the trailer lamps as intended |1.9.4| | 1 |
| Nearside Rear Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Front Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Front Exhaust system not adequately supported |7.1.1| | 1 |
| Stop lamp not working |1.2.1b| | 1 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
| Brake pedal creeps down under servo assistance and touches the floor |3.3.C.3| | 1 |
| Nearside Leaf spring has excessive wear in an anchor pin and/or bush |2.4.B.2| | 1 |
| Offside Front Coil spring not correctly located |2.4.C.2| | 1 |
| Brake pedal spongy |3.3.B.1b| | 1 |
| Rear Brake cable has restricted free movement |3.5.1k| | 1 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Brake cable has restricted free movement |3.5.1k| | 1 |
| Offside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Offside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Service brake: efficiency below requirements |3.7.C.1a| | 1 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 1 |
| Rear fog lamp not working |1.3.2b| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Rear Mechanical brake component has restricted free movement | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Headlamp not in good working order |not working| |1.2.4a| | 1 |
| Body has a projection caused by damage |6.1.C.1| | 1 |
| Rear Body has a projection caused by damage |6.1.C.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear An item not tested |Manual| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Headlamp aim not tested |1.8.A.1c| | 1 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
| Offside Outer Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| Horn not loud enough to be heard by another road user |1.6.2b| | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Centre Front Statutory seat belt missing |5.1.1| | 1 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
| Fuel cap/sealing device sealing washer missing |7.2.4c| | 1 |
| Offside Front Macpherson strut upper support bearing is stiff in operation |2.5.B.1b| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Exhaust emits visible black smoke at idle |7.3.A.2b| | 1 |
| Offside Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Centre Exhaust mounting missing |7.1.1b| | 1 |
| Centre Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Nearside Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Headlamp insecure |1.7.3| | 1 |
| Nearside Rear Rear position lamp|s| incomplete |1.1.4a| | 1 |
| Nearside Front Direction indicator incomplete |1.5.A1b| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner valance |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded valance |2.4.A.3| | 1 |
| Offside Front Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings by engine mounting |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings to crossmember |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings to jacking point |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outrigger |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outrigger |6.1.B.2| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Side repeater not working |1.4.A.2c| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Seat belt locking mechanism does not secure or release missing |5.2.5a| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded inner valance |2.4.A.3| | 1 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Centre Statutory seat belt missing |5.1.1| | 1 |
| Emissions not tested Engine over heating, fans inoperative. (8.2.1.2 (d)) | 1 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 1 |
| Front Hazard warning lamps inoperative nearside and offside (4.4.1 (e)) | 1 |
| Rear Hazard warning lamps inoperative nearside and offside (4.4.1 (e)) | 1 |
| Hazard warning switch inoperative (4.4.2 (a) (ii)) | 1 |
| Offside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 1 |
| Offside Front Upper Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch adjacent to engine mounting prescribed area (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting leaf spring/body mounting (6.2.2 (d) (i)) | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill/body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting leaf spring/body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting body mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting chassis under wheel front wheel arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Towbar excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Brake pipe likely to become detached or damaged routed incorrect, fouling anti roll bar (1.1.11 (d) (ii)) | 1 |
| Windscreen wiper not working (3.4 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Headlamp levelling device inoperative both (4.1.5 (a)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced lower sidesill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower adjacent to offside rear leaf spring mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced lower wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Upper Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis, on jacking point (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis, on jacking point (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength whole sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Upper coil tower excessively corroded X3 (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Upper coil tower excessively corroded X3 (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Spring hanger mount X3 (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Spring hanger mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced lower wheel archadjacent to offside front cross member prescribed area (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced lower wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength rear leaf spring mounting prescribed area (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength rear of leaf spring prescribed area in two areas (5.3.6 (a) (i)) | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 1 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
| Offside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Offside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch at end of outer sill (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner under sill 7 rust holes (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure inadequately repaired such that structural rigidity is significantly reduced inner under sill repair not continuously seam welded in one place (6.1.1 (d) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail under engine mounting hole (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch holed by chassis rail behind engine mounting, beside brake hose mounts (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced lower undersill one rust hole (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Integral body structure inadequately repaired such that structural rigidity is significantly reduced undersill one repair not continuously seam welded (6.1.1 (d) (i)) | 1 |
| Nearside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner side sill adjacent to nearside rear leaf spring mounting prescribed area (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength adjacent to nearside rear leaf spring mounting prescribed area (5.3.6 (a) (i)) | 1 |
| Offside Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner centre sill (6.1.1 (c) (i)) | 1 |
| Nearside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill adjacent to nearside rear seat belt mount prescribed area (two places) (6.1.1 (c) (i)) | 1 |
| Nearside Rear Upper Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner adjacent to offside rear leaf spring mount prescribed area (5.3.6 (a) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced nearside and offside steps holed (6.1.1 (c) (i)) | 1 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced step sill area (7.1.1 (a) (i)) | 1 |
| Exhaust silencer insecure mountings missing (8.1.1 (b) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Emissions unable to be completed Major exhaust blow (8.2.1.2 (d)) | 1 |
| Offside Front Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Seat belt webbing significantly weakened (7.1.2 (b) (ii)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Electrical wiring insulation so damaged or deteriorated it is likely to cause a short-circuit wiring hanging down fouling on exhaust (4.11 (c) (ii)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced middle inner and outer sill (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced step area (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced step area (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (behind shock) (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch(behind rear wheel) (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (behind wheel) (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced shock tower (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member (6.1.1 (c) (i)) | 1 |
| Offside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Brake servo defective or ineffective hose leaking (1.1.10 (a) (i)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring mounting (5.3.6 (a) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases Manifold area (6.1.2 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outrigger area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outrigger area (5.3.6 (a) (i)) | 1 |
| Nearside Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Near spring (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Near spring (5.3.6 (a) (i)) | 1 |
| Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Nearside Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |