| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 61 |
| Headlamp aim out of alignment | 47 |
| Registration plate lamp issues | 21 |
| Brakes imbalanced across an axle | 17 |
| Rear brake binding | 14 |
| Nearside Stop lamp not working |1.2.1b| | 10 |
| Registration plate issues | 9 |
| Parking brake lever has no reserve travel |3.1.6b| | 8 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 8 |
| Offside Stop lamp not working |1.2.1b| | 7 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 6 |
| Service brake: efficiency below requirements |3.7.B.7| | 6 |
| Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 5 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 5 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 5 |
| Horn not working |1.6.2a| | 5 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 4 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 4 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 4 |
| Rear parking brake recording little or no effort | 4 |
| Parking brake: efficiency below requirements |3.7.B.7| | 4 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 4 |
| Exhaust system not adequately supported |7.1.1| | 3 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 3 |
| Offside Front Headlamp aim beam image kick up to the offside |1.8| | 3 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 3 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 3 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 3 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 3 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 3 |
| Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 3 |
| Brake hose excessively deteriorated | 3 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
| Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 2 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Rear Stop lamp not working |1.2.1b| | 2 |
| Offside Rear Position lamp not working |4.2.1 |a|| | 2 |
| Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 2 |
| Nearside Headlamp aim projected beam image is obviously incorrect kick up to the right (4.1.2 (c)) | 2 |
| Nearside Headlamp levelling device inoperative |4.1.5 |a|| | 2 |
| Offside Headlamp levelling device inoperative |4.1.5 |a|| | 2 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 2 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 2 |
| Bonnet cannot be secured in the closed position |8.4.1| | 2 |
| Anti-lock braking system warning lamp indicates an ABS fault | 2 |
| Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b)) | 2 |
| Nearside Rear Outline marker lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Mechanical brake component has restricted free movement | 2 |
| Parking brake efficiency below requirements |1.4.2 |a| |i|| | 2 |
| Offside Rear fog lamp not working |1.3.2b| | 2 |
| Nearside Rear Direction indicator incorrect colour |4.4.3 |a|| | 2 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Rear brake application uneven | 2 |
| Stop lamp not working |1.2.1b| | 2 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 2 |
| Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 2 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 2 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Brake pipe excessively corroded | 2 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
| Fuel system component leaking |7.2.3| | 2 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Offside Front Service brake excessively fluctuating (1.2.1 (e)) | 2 |
| Windscreen washer not working | 2 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Headlamp levelling device inoperative (4.1.5 (a)) | 2 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Rear fog lamp not working |1.3.2b| | 2 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Driver`s seat fore and aft adjustment mechanism not functioning as intended. |6.2.A.3| | 1 |
| Exhaust system not adequately supported Front pipe mounting missing |7.1.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Stop lamp(s) lens defective such that the emitted light is adversely affected (4.3.1 (b) (ii)) | 1 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Emissions not tested |7.0| | 1 |
| Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Front Seat belt webbing significantly weakened cut from edge greater than 2mm (7.1.2 (b)) | 1 |
| Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Nearside Rear Leaf spring fractured (5.3.1 (b) (i)) | 1 |
| Offside Rear Rear fog lamp missing |1.3.2a| | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Headlamp aim not tested due to not working on dip beam (4.1.2 (b)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength front mount |5.3.6 |a| |i|| | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect kick up to the right (4.1.2 (c)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Front Direction indicator incorrect colour both (4.4.3 (a)) | 1 |
| Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both arches (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jack point/out rigger (5.3.6 (a) (i)) | 1 |
| Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced both sills/floor pan (7.1.1 (a) (i)) | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Nearside Front Headlamp insecure (4.1.1 (c)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch (5.3.6 (a) (i)) | 1 |
| Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Front Road wheel more than one fixing loose (5.2.1 (a) (ii)) | 1 |
| Power steering pipe/hose excessively corroded x2 on rack |2.1.5 |g| |i|| | 1 |
| Nearside Front Inner Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| rear parking |secondary| brakes imbalanced | 1 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Offside Rear Direction indicator light intensity significantly reduced |4.4.3 |a|| | 1 |
| Exhaust has a major leak of exhaust gases downpipe (6.1.2 (a)) | 1 |
| Emissions not tested (8.2.1.2 (d)) | 1 |
| Nearside Rear Leaf spring anchor bracket modified and seriously weakened |2.4.A.2| | 1 |
| Offside Rear Leaf spring anchor bracket modified and seriously weakened |2.4.A.2| | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength INNER WHEEL ARCH AREA (5.3.6 (a) (i)) | 1 |
| Offside Rear Rear position lamp|s| not working side light |1.1.A.3b| | 1 |
| Offside Front Service brake lagging in operation |1.2.1 |d|| | 1 |
| Offside Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
| Nearside Front Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Front Exhaust has a major leak of exhaust gases front down pipe |6.1.2 |a|| | 1 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Rear Mechanical brake component has restricted free movement | 1 |
| Offside Rear Electrical wiring insulation so damaged or deteriorated it is likely to cause a short-circuit at wheel (4.11 (c) (ii)) | 1 |
| Offside Rear rear brake recording little or no effort service brake |3.7.B.5a| | 1 |
| Offside Rear Upper Outline marker lamp does not illuminate simultaneously with the position lamps (4.2.2 (a)) | 1 |
| Offside Front Outer Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Nearside Front Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Rear Service brake grabbing severely |3.7.C.2| | 1 |
| Driver`s seat insecure |6.2.A.1| | 1 |
| Brake hose damaged | 1 |
| Nearside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Front Exhaust system not adequately supported |7.1.1| | 1 |
| Exhaust has a major leak of exhaust gases tailpipe section (6.1.2 (a)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect poss. bulb in wrong (4.1.2 (c)) | 1 |
| Offside Stop lamp|s| light intensity significantly reduced |4.3.3 |a| |ii|| | 1 |
| Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member |6.1.1 |c| |i|| | 1 |
| Nearside Front Outer Headlamp has a product on the light source so that the light output is severely reduced product on glass |4.1.4 |b|| | 1 |
| Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Rear Outer Stop lamp not working |1.2.1b| | 1 |
| Nearside Outer Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Offside Outer Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded in wheel arche |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded near engine mounting, inside wheel arche |2.4.A.3| | 1 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Nearside Front Inner Brake prescribed area is excessively corroded brake pipe / hose mounting (1.1.21 (e) (i)) | 1 |
| Nearside Front Lower Subframe mounting prescribed area excessively corroded significantly reducing structural strength in wheel arche (5.3.6 (a) (i)) | 1 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Front Direction indicator incorrect colour showing white (4.4.3 (a)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring tower (5.3.6 (a) (i)) | 1 |
| Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Power steering pipe/hose excessively corroded across rack x 2 (2.1.5 (g) (i)) | 1 |
| Power steering pipe/hose excessively corroded pump to rack (2.1.5 (g) (i)) | 1 |
| Power steering pipe/hose excessively corroded rack to reservoir (2.1.5 (g) (i)) | 1 |
| Indicator switch faulty |1.4.A.1| | 1 |
| Rear fog lamp obviously incorrectly positioned |1.3.2a| | 1 |
| Exhaust has a major leak of exhaust gases downpipe broken at the flange |7.1.2| | 1 |
| Offside Rear Direction indicator incorrect colour |4.4.3 |a|| | 1 |
| Offside Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 1 |
| Nearside Rear position lamp|s| insecure |1.1.A.3a| | 1 |
| Front Fuel system component leaking |7.2.3| | 1 |
| Nearside Front Coil spring not correctly located |2.4.C.2| | 1 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength rear mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Rear Service brake grabbing severely (1.2.1 (c)) | 1 |
| Nearside Front Outline marker lamp not working |4.2.1 |a|| | 1 |
| Offside Front Outline marker lamp not working |4.2.1 |a|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front upper of inner arch (5.3.6 (a) (i)) | 1 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Brake pipe leaking on a hydraulic braking system front to rear (1.1.11 (b) (ii)) | 1 |
| Brake performance not tested (1.2.1 (g)) | 1 |
| Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 1 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Service brake indicates brake bind |3.7.D.2a| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front chassis (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn front bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Front Suspension arm pin or bush excessively worn front bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Rear An item not tested |Manual| | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering suspension strut turret (6.1.1 (c) (ii)) | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering strut turret (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
| Nearside Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in 30cm of the leaf spring rear mount |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in 30cm of o/s/r leaf spring rear mount |5.3.6 |a| |i|| | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner seal in 30cm of n/s/r leaf spring front mount |5.3.6 |a| |i|| | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area is excessively corroded sill (5.2.6) | 1 |
| Nearside Front Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Parking brake: efficiency below requirements (3.7.B.7) | 1 |
| Nearside Rear Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 1 |
| Offside Rear Parking (secondary brake) on a single line braking system has no recorded effort at a wheel (1.3.1 (a) (ii)) | 1 |
| Brake pedal has insufficient reserve travel PEDAL GOES TO FLOOR (1.1.2 (a)) | 1 |
| Offside Front Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Rear Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 1 |
| Nearside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Offside Front Exhaust has a major leak of exhaust gases leaking gas from bottom of downpipe |6.1.2 |a|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger next to jacking point holed and corroded |5.3.6 |a| |i|| | 1 |
| Offside Rear Seat belt damaged (7.1.2 (b) (i)) | 1 |
| Offside Front Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outrigger |6.1.1 |c| |i|| | 1 |
| Nearside Front Wheel bearing so rough it is likely to overheat or break up |5.1.3 |b| |ii|| | 1 |
| Offside Front Wheel bearing so rough it is likely to overheat or break up |5.1.3 |b| |ii|| | 1 |
| Offside Front front brake binding |3.7.B.1| | 1 |
| Nearside Rear front brake binding |3.7.B.1| | 1 |
| Offside Rear front brake binding |3.7.B.1| | 1 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Brake load sensing valve linkage defective and function impaired |1.1.17 |a|| | 1 |
| Wheel bearing rough when rotated n/s/r wheel bearing (5.1.3 (b) (i)) | 1 |
| Offside Rear Hydraulic brake cylinder leaking and braking performance affected (1.1.16 (b) (ii)) | 1 |
| Nearside Upper Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Upper Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Lower Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Front Bumper insecure shield guard was detached from bumper (6.1.4 (a) (i)) | 1 |
| Central Rear Electrical wiring likely to drag on the ground (4.11 (a) (iii)) | 1 |
| Offside Front Direction indicator incorrect colour white (4.4.3 (a)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Front Exhaust has a major leak of exhaust gases at turbo (6.1.2 (a)) | 1 |
| Front Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Emissions unable to be completed (8.2.2.2 (e)) | 1 |
| Parking brake lever is impeded in its travel |3.1.6c| | 1 |
| Nearside Front Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point area (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength X2 areas (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength X2 areas (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced X3 (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill. (7.1.1 (a) (i)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Rear mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength front mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength excessive corrosion within 30cm of strut mounting (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength excessive corrosion within 30cm of shock absorber mounting (5.3.6 (a) (i)) | 1 |
| Nearside Rear Shock absorbers has a serious fluid leak | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL (6.2.2 (d) (i)) | 1 |
| Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Emissions not tested |7.4.B.1| | 1 |
| Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Nearside Outline marker lamp missing (4.2.1 (a) (ii)) | 1 |
| Offside Outline marker lamp missing (4.2.1 (a) (ii)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Front brake disc in such a condition that it is seriously weakened | 1 |
| Exhaust system not adequately supported hanger broken |7.1.1| | 1 |
| Stop lamp(s) not working All (4.3.1 (a) (ii)) | 1 |
| Rear Brake load sensing valve seized but ABS functioning (1.1.17 (c) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
| Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Nearside Rear Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Front Anti-lock braking system component excessively damaged ABS ring damaged/ partially missing (1.6 (e)) | 1 |
| Offside Front Anti-lock braking system component excessively damaged ABS ring damaged/ partially missing (1.6 (e)) | 1 |
| Anti-lock braking system warning lamp does not illuminate Tell tale does not work (1.6 (a)) | 1 |
| Nearside Rear Service brake excessively binding 2nd axle (1.2.1 (f)) | 1 |
| Nearside Rear Service brake excessively binding 3rd axle (1.2.1 (f)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced around jacking point and sills (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced around jacking point and sills (6.1.1 (c) (i)) | 1 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Nearside Front Anti-lock braking system component excessively damaged ABS ring (1.6 (e)) | 1 |
| Offside Front Anti-lock braking system component excessively damaged ABS ring (1.6 (e)) | 1 |
| Offside Rear Service brake excessively binding front (1.2.1 (f)) | 1 |
| Nearside Rear Service brake excessively binding front (1.2.1 (f)) | 1 |
| Nearside Rear Service brake excessively binding rear (1.2.1 (f)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Jacking point (6.1.1 (c) (i)) | 1 |
| Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Exhaust emissions test aborted because smoke levels are significantly in excess of the specified limit values |8.2.2.2 |f|| | 1 |
| Offside Outline marker lamp not working |4.2.1 |a|| | 1 |