| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 71 |
| Headlamp aim out of alignment | 38 |
| Registration plate lamp issues | 35 |
| Brakes imbalanced across an axle | 20 |
| Rear brake binding | 18 |
| Parking brake: efficiency below requirements |3.7.B.7| | 16 |
| Offside Rear fog lamp not working |1.3.2b| | 10 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 9 |
| Nearside Stop lamp not working |1.2.1b| | 9 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 8 |
| Horn not working |1.6.2a| | 8 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 7 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 7 |
| Anti-lock braking system warning lamp indicates an ABS fault | 7 |
| Offside Stop lamp not working |1.2.1b| | 7 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 7 |
| Brake hose excessively deteriorated | 7 |
| Registration plate issues | 7 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 6 |
| Horn not working (7.7 (a)) | 6 |
| Rear parking brake recording little or no effort | 6 |
| Service brake: efficiency below requirements |3.7.B.7| | 6 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 5 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 5 |
| Brake pipe excessively corroded | 5 |
| Exhaust system not adequately supported |7.1.1| | 4 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 4 |
| Offside Rear Stop lamp not working |1.2.1b| | 4 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 4 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 4 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 4 |
| Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 4 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 4 |
| Nearside Rear Position lamp not working |4.2.1 |a|| | 4 |
| Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 4 |
| Rear fog lamp not working |1.3.2b| | 3 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 3 |
| Windscreen has damage | 3 |
| Offside Rear Outline marker lamp not working (4.2.1 (a) (ii)) | 3 |
| Nearside Front Direction indicator incorrect colour |4.4.3 |a|| | 3 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Front brake excessively fluctuating | 3 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 3 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 3 |
| Parking brake lever has no reserve travel |3.1.6b| | 3 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 3 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Brake performance not tested (1.2.1 (g)) | 2 |
| Offside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 2 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 2 |
| Offside front brake binding |3.7.B.1| | 2 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Windscreen wiper not working (3.4 (a)) | 2 |
| Windscreen washer not working | 2 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 2 |
| Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 2 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 2 |
| Horn not working (7.7 (a) (ii)) | 2 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 2 |
| Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 2 |
| Brake load sensing valve linkage seized |3.6.E.3| | 2 |
| Nearside Front front brake binding |3.7.B.1| | 2 |
| Rear Mechanical brake component has restricted free movement | 2 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 2 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 2 |
| Mechanical brake component has restricted free movement | 2 |
| Direction indicators flashing more than 120 times a minute |1.4.A.2g| | 2 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Battery insecure |1.9.1| | 2 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 2 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 2 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 2 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Nearside Rear Outline marker lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 2 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 2 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 2 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 2 |
| Central Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Nearside front brake binding |3.7.B.1| | 2 |
| Offside Windscreen wiper blade missing |8.2.2| | 1 |
| Nearside Outer Outline marker lamp not working x 3 repaired on site (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Outline marker lamp not working lights out (4.2.1 (a) (ii)) | 1 |
| Nearside Front Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Offside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced at lower crossmember (6.1.1 (c) (i)) | 1 |
| Nearside Service brake excessively binding middle (1.2.1 (f)) | 1 |
| Offside Front Driver`s door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Lower Exhaust has a major leak of exhaust gases hole in down pipe first box |7.1.2| | 1 |
| Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b)) | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Nearside Rear Stop lamp has less than 50% of the light sources illuminating |1.2.1b| | 1 |
| Offside Rear Stop lamp has less than 50% of the light sources illuminating |1.2.1b| | 1 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Offside Front Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |3.3 |b| |ii|| | 1 |
| Front Exhaust has a major leak of exhaust gases Front pipe holed |6.1.2 |a|| | 1 |
| Nearside Front Braking system leaking |3.6.A.1| | 1 |
| Offside Front Lower Radius arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| All position lamps adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
| Nearside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
| Offside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
| Offside Rear Position lamp not working and lens broken / missing (4.2.1 (a) (ii)) | 1 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Oil leaking excessively from transmission (8.4.1 (a) (i)) | 1 |
| Nearside Front Inner Prop shaft joint constant velocity boot no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Electronic stability control warning lamp indicates a fault |7.12 |e|| | 1 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Nearside Inner Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Rear fog lamp missing |1.3.2a| | 1 |
| Nearside Rear Upper All outline marker lamps not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect kick beam wrong side |4.1.2 |c|| | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect kick beam wrong side |4.1.2 |c|| | 1 |
| Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 1 |
| Offside Rear Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Drive shaft securing bolt loose bearing carrier to rear of engine, lower bolt loose (6.1.7 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced on bottom of chassis leg, near to radiator cross member mounting (6.1.1 (c) (i)) | 1 |
| Offside Front front brake binding |3.7.B.1| | 1 |
| Nearside Rear front brake binding |3.7.B.1| | 1 |
| Offside Rear front brake recording little or no effort |3.7.B.5a| | 1 |
| Offside Rear front parking brake recording little or no effort |3.7.B.6a| | 1 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Centre Stop lamp not working |1.2.1b| | 1 |
| Offside Front Direction indicator does not face the front (4.4.3 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Nearside Rear Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting spring turret (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting spring turret (6.2.2 (d) (i)) | 1 |
| Power steering pipe/hose excessively corroded all power steering pipes (2.1.5 (g) (i)) | 1 |
| Exhaust has a major leak of exhaust gases Front exhaust section |7.1.2| | 1 |
| Exhaust system not adequately supported 2x exhaust rubber mountings broken & tailpipe damaged such that mounting is ineffective |7.1.1| | 1 |
| Rear fog lamp missing No bulb holder in lamp |1.3.2a| | 1 |
| Offside Rear Direction indicator obviously incorrectly positioned Incorrect lamp fitted |1.4.A.2b| | 1 |
| Central Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 1 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 1 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction removed (3.1 (a) (ii)) | 1 |
| Nearside Front Upper Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Upper All outline marker lamps not working (4.2.1 (a) (ii)) | 1 |
| Direction indicator not working offside rear (4.4.1 (a) (ii)) | 1 |
| Driver`s door catch deteriorated so the door cannot be readily opened or closed |6.2.B.2| | 1 |
| All position lamps not working |1.1.A.3b| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Exhaust silencer likely to become detached |8.1.1 |b| |ii|| | 1 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Nearside Outline marker lamp not working marker lamps not working (4.2.1 (a) (ii)) | 1 |
| Offside Outline marker lamp not working marker lamps not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Rear reflector missing (4.8.2 (a) (ii)) | 1 |
| Headlamp not working on main beam both (4.1.1 (a) (ii)) | 1 |
| Central Exhaust system insecure |6.1.2 |a|| | 1 |
| Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Obligatory mirror insecure |8.1.1| | 1 |
| Nearside Rear reflector insecure |1.5.1a| | 1 |
| Central Rear Electrical wiring insecure tow bar |1.9.2a| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis rail badly corroded (5.3.6 (a) (i)) | 1 |
| Central Front Upper Power steering pipe/hose excessively corroded on rack (2.1.5 (g) (i)) | 1 |
| Central Front Lower Power steering pipe/hose excessively corroded on rack (2.1.5 (g) (i)) | 1 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting INNER WING SPRING TURRET (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting INNER WING SPRING TURRET (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting JACKING POINT OUT RIGGER (6.2.2 (d) (i)) | 1 |
| Offside Integral body structure inadequately repaired such that structural rigidity is significantly reduced INNER SILL PANEL (6.1.1 (d) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced FORWARD SUPPORT PANEL (6.1.1 (c) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced REAR SUPPORT PANEL (6.1.1 (c) (i)) | 1 |
| Nearside Rear Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Offside Front Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Headlamp aim projected beam image is obviously incorrect both european pattern (4.1.2 (c)) | 1 |
| Offside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Front brake disc in such a condition that it is seriously weakened | 1 |
| Offside Rear Direction indicator adversely affected by the operation of another lamp (4.4.3 (b)) | 1 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Emissions not tested |7.0| | 1 |
| Nearside Rear An item not tested |Manual| | 1 |
| Nearside Rear Position lamp not working trailer board light inopp (4.2.1 (a) (ii)) | 1 |
| Offside Rear Position lamp not working body light inopp (4.2.1 (a) (ii)) | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases front pipe (6.1.2 (a)) | 1 |
| Exhaust system insecure all exhaust rubbers perished (6.1.2 (a)) | 1 |
| Emissions unable to be completed due too exhaust (8.2.2.2 (e)) | 1 |
| Nearside Front Brake prescribed area is excessively corroded Under battery (1.1.21 (e) (i)) | 1 |
| Offside Front Headlamp lens seriously defective Water ingress (4.1.1 (b) (ii)) | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill (7.1.1 (a) (i)) | 1 |
| Offside Outline marker lamp does not illuminate simultaneously with the position lamps x2 (4.2.2 (a)) | 1 |
| Nearside Headlamp insecure (4.1.1 (c)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Offside Front Brake pipe leaking on a hydraulic braking system Brake pipe (1.1.11 (b) (ii)) | 1 |
| Nearside Rear Exhaust on a vehicle fitted with a diesel particulate filter emits visible smoke of any colour (8.2.2.2 (d)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area fractured significantly reducing structural strength chassis outrigger / jacking point (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area fractured significantly reducing structural strength chassis outrigger / jacking point (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area fractured significantly reducing structural strength chassis / subframe mounting point (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength nearside chassis leg at subframe mounting (5.3.6 (a) (i)) | 1 |
| Offside Rear position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 1 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Front Position lamp not working front top position lamps not working |4.2.1 |a|| | 1 |
| Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Parking brake recording little or no effort |3.7.D.3a| | 1 |
| Parking brake: efficiency below requirements |3.7.D.4| | 1 |
| Rear Service brake application uneven across the axle |3.7.D.2b| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength rear mount |5.3.6 |a| |i|| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength rear mount |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring front mount |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring front mount |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 1 |
| Offside Parking brake mechanism/associated mounting prescribed area is excessively corroded floor |1.1.21 |e| |i|| | 1 |
| Nearside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Exhaust has a major leak of exhaust gases frontpipe corroded |7.1.2| | 1 |
| Subframe mounting prescribed area is excessively corroded front subframe within 30cms of rear offside mounting point |by jacking point| |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded offside front chassis by cross member mounting point |2.4.A.3| | 1 |
| Offside Front Direction indicator incorrect colour |4.4.3 |a|| | 1 |
| Electrical wiring insecure |1.9.2a| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch / to strut top area (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg at subframe mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch to strut tower (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis at subframe mount area (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer body section at chassis outer rigger (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer body section at chassis outer rigger (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill and llower step area (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill to step area (7.1.1 (a) (i)) | 1 |
| Nearside Rear Leaf spring longitudinally displaced |2.4.B.1d| | 1 |
| Offside Rear Leaf spring longitudinally displaced |2.4.B.1d| | 1 |
| Rear Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
| Nearside Rear Lower Brake load sensing valve linkage defective and function impaired seized (1.1.17 (a)) | 1 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
| Brake load sensing valve linkage obviously incorrectly adjusted (1.1.17 (b)) | 1 |
| Central Stop lamp not working |1.2.1b| | 1 |
| Nearside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Rear Brake cable has restricted free movement (1.1.15 (e)) | 1 |
| Offside Rear Brake cable has restricted free movement (1.1.15 (e)) | 1 |
| Brake performance not tested due to brake pipe condition (1.2.1 (g)) | 1 |
| Rear Parking |secondary brake| on a single line braking system grabbing severely Also sticking on |1.3.1 |c|| | 1 |
| Offside Rear Direction indicator incorrect colour |4.4.3 |a|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength By jacking point |5.3.6 |a| |i|| | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Behind front door area in box section between chassis and outer sill |5.3.6 |a| |i|| | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Behind front door area in box section between chassis and outer sill |5.3.6 |a| |i|| | 1 |
| Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 1 |
| Central Front Power steering pipe/hose excessively corroded on rack (2.1.5 (g) (i)) | 1 |
| Rear Direction indicator incorrect colour Both (4.4.3 (a)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Both inner strut towers (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp aim not tested (4.1.2 (b)) | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Exhaust emissions exceed manufacturers specified limit 1.81 (8.2.2.2 (a)) | 1 |
| Offside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Hazard warning switch inoperative (4.4.2 (a) (ii)) | 1 |
| Nearside Rear Upper Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Horn sound not in accordance with requirements (7.7 (c)) | 1 |
| Offside Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Offside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Obligatory mirror insecure |8.1.1| | 1 |
| Offside Front Position lamp not working |4.2.1 |a|| | 1 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Exhaust fumes causing a danger to health of persons on board side exit tailpipe missing. (6.1.2 (b) (ii)) | 1 |
| Nearside Rear Stop lamp(s) adversely affected by the operation of another lamp position lamp (4.3.3 (b)) | 1 |
| Exhaust has a major leak of exhaust gases lower end of turbo down pipe (6.1.2 (a)) | 1 |
| Emissions not tested major leak (8.2.2.2 (e)) | 1 |
| Fuel pipe leaking FUEL TANK FILLER PIPE CORRODED |6.1.3 |b| |i|| | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Offside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Centre Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Brake cable damaged (1.1.15 (a)) | 1 |
| Nearside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Brake load sensing valve seized but ABS functioning (1.1.17 (c) (i)) | 1 |
| Exhaust has a major leak of exhaust gases both rear tail boxes and some areas of the pipe is leaking gases (6.1.2 (a)) | 1 |
| Offside Front Oil leaking continuously from engine posing a serious risk to road safety heat exchanger (8.4.1 (a) (ii)) | 1 |
| Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
| Offside Front Service brake lagging in operation (1.2.1 (d)) | 1 |
| Nearside Front Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Emissions not tested oil leak (8.2.2.2 (e)) | 1 |
| Offside Obligatory mirror insecure (3.3 (b) (ii)) | 1 |
| Front All direction indicators incorrect colour white (4.4.3 (a)) | 1 |
| Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced towbar assy (6.1.1 (c) (i)) | 1 |
| Towbar component excessively corroded (6.1.6 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Jacking point. (6.1.1 (c) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Jacking point. (5.3.6 (a) (i)) | 1 |
| Exhaust system not adequately supported rubbers deterriorated |7.1.1| | 1 |
| Offside Rear Service brake lagging in operation right rear (1.2.1 (d)) | 1 |
| Nearside Towbar component defective badly corroded and reduced in thickness |6.1.6 |a|| | 1 |
| Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Central Front Exhaust has a major leak of exhaust gases Down pipe broken (6.1.2 (a)) | 1 |
| Emissions not tested Due to major exhaust leak (8.2.2.2 (e)) | 1 |
| Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Front Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
| Offside Front Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced X2 (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill and jacking point (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill corroded at rear spring mount (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Front Parking brake mechanism/associated mounting prescribed area is excessively corroded (1.1.21 (e) (i)) | 1 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking mount (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking mount (6.1.1 (c) (i)) | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Front Upper Outline marker lamp with a multiple light source more than 1/2 not functioning (4.2.1 (a) (ii)) | 1 |
| Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting inner arch front of vehicle (6.2.2 (d) (i)) | 1 |
| Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch area (5.3.6 (a) (i)) | 1 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Parking brake lever has no reserve travel +offside |3.1.6b| | 1 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Exhaust system not adequately supported rubber mountings broken |7.1.1| | 1 |
| Nearside Rear Direction indicators not working |1.4.A.2c| | 1 |
| Rear fog lamp not working bulb fitted (4.5.1 (a) (ii)) | 1 |
| Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Front Brake pipe at imminent risk of failure or fracture brake pipe excessivly corroded and leaking brake fluid (1.1.11 (a)) | 1 |
| Indicator switch inoperative (4.4.2 (a) (ii)) | 1 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced crossmember (6.1.1 (c) (i)) | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Offside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner step (6.1.1 (c) (i)) | 1 |
| Brake performance unable to be tested burst pipe (1.2.1 (g)) | 1 |
| Front brake application uneven | 1 |