Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 74 |
Headlamp aim out of alignment | 62 |
Brake pipe excessively corroded | 50 |
Horn not working |1.6.2a| | 26 |
Registration plate lamp issues | 24 |
Brakes imbalanced across an axle | 12 |
Rear brake binding | 10 |
Service brake: efficiency below requirements |3.7.B.7| | 7 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 7 |
Offside Rear fog lamp not working |1.3.2b| | 7 |
Horn not working (7.7 (a) (ii)) | 5 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 5 |
Horn not working (7.7 (a)) | 5 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Exhaust system not adequately supported |7.1.1| | 5 |
Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 4 |
Offside Front Shock absorber has a serious fluid leak |2.7.3| | 4 |
Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Battery insecure |1.9.1| | 4 |
Horn not working |7.7 |a| |ii|| | 4 |
Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 4 |
Rear fog lamp not working |1.3.2b| | 4 |
Offside Headlamp not working on dipped beam |1.7.5a| | 4 |
Windscreen washer not working | 3 |
Parking brake: efficiency below requirements |3.7.B.7| | 3 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Rear fog lamp not working |4.5.1 |a| |ii|| | 3 |
Registration plate issues | 3 |
Centre Exhaust system not adequately supported |7.1.1| | 3 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 3 |
Nearside Front Direction indicator not working |1.4.A.2c| | 3 |
Rear Mechanical brake component has restricted free movement | 3 |
Brake load sensing valve linkage seized |3.6.E.3| | 3 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 3 |
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 3 |
Nearside Stop lamp not working |1.2.1b| | 3 |
Brake hose excessively deteriorated | 3 |
Brake performance not tested (1.2.1 (g)) | 3 |
Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 3 |
Offside Stop lamp not working |1.2.1b| | 3 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 3 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 3 |
Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
Windscreen wiper blade insecure | 3 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
Front brake application uneven | 2 |
Offside Front Subframe mounting prescribed area is excessively corroded chassis |2.4.A.3| | 2 |
Nearside Front Subframe mounting prescribed area is excessively corroded chassis |2.4.A.3| | 2 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 2 |
Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 2 |
Offside Side repeater not working |1.4.A.2c| | 2 |
Front Direction indicator incorrect colour |1.4.A.2f| | 2 |
Offside Front Direction indicator incorrect colour |1.4.A.2f| | 2 |
Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 2 |
Offside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
Offside Rear Rear fog lamp not working |1.3.2b| | 2 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
Offside Front Shock absorbers has a serious fluid leak | 2 |
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 2 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Offside Front Direction indicator not working |1.4.A.2c| | 2 |
Offside Side repeater not working (4.4.1 (a) (ii)) | 2 |
Front Exhaust system not adequately supported |7.1.1| | 2 |
Rear Exhaust system not adequately supported |7.1.1| | 2 |
Nearside Rear Stop lamp not working |1.2.1b| | 2 |
Offside Rear Stop lamp not working |1.2.1b| | 2 |
Rear Stop lamp not working |1.2.1b| | 2 |
Nearside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Offside front brake binding |3.7.B.1| | 2 |
Brake load sensing valve seized |3.6.E.3| | 2 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Nearside Front Shock absorbers has a serious fluid leak | 2 |
Nearside Side repeater not working |1.4.A.2c| | 2 |
Brake hose damaged | 2 |
Front Exhaust mounting missing |7.1.1b| | 2 |
Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 2 |
Offside Front Position lamp not working |4.2.1 |a|| | 2 |
Front Direction indicators incorrect colour |1.4.A.2f| | 2 |
Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 2 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 2 |
Offside Front Upper Front position lamp|s| not working |1.1.A.3b| | 2 |
Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
Rear parking brake recording little or no effort | 1 |
Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
Offside Front Suspension spring mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
Nearside Front Brake pipe leaking |3.6.A.1| | 1 |
Offside Front Suspension component mounting prescribed area is inadequately repaired inner arch |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area is inadequately repaired inner arch |2.4.A.3| | 1 |
Brake performance not tested |3.7.A.1| | 1 |
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing areas x 2 (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch areas |5.3.6 |a| |i|| | 1 |
Nearside Rear Shock absorber has an excessively worn shock absorber pivot |2.7.4| | 1 |
Offside Rear Shock absorber has an excessively worn shock absorber pivot |2.7.4| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch areas (5.3.6 (a) (i)) | 1 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Rear Service brake excessively binding TAG AXLE (1.2.1 (f)) | 1 |
Offside Front Brake hose damaged and likely to fail Bulged (1.1.12 (a)) | 1 |
Offside Outer Parking brake mechanism/associated mounting prescribed area is excessively corroded sill panel holed |3.1.9| | 1 |
Nearside Upper Front position lamp|s| not working |1.1.A.3b| | 1 |
Offside Rear Brake pipe excessively chafed |3.6.B.2c| | 1 |
Rear Brake pipe inadequately supported |3.6.B.1| | 1 |
Nearside Front Brake pipe excessively chafed |3.6.B.2c| | 1 |
Stop lamp has less than 50% of the light sources illuminating HIGH LEVEL |1.2.1b| | 1 |
Centre Rear Stop lamp has less than 50% of the light sources illuminating |1.2.1b| | 1 |
Offside Front Brake pipe leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chalked (6.1.1 (c) (i)) | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Chalked (6.1.1 (c) (i)) | 1 |
Windscreen has damage | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wing (6.2.2 (d) (i)) | 1 |
Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced crossmember severly corroded (6.1.1 (c) (i)) | 1 |
Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
Central Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
Front brake disc in such a condition that it is seriously weakened | 1 |
Windscreen wiper blade missing |8.2.2| | 1 |
Drivers seat moving inadvertently (6.2.5 (b) (ii)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER WING (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER WING (5.3.6 (a) (i)) | 1 |
Offside Rear Upper Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Electrical wiring insecure |1.9.2a| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded FLOOR JACKING POINT |5.2.6| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded CHASSIS |2.4.A.3| | 1 |
Front Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
Offside Rear Axle has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
Offside Rear Position lamp not working |4.2.1 |a| |ii|| | 1 |
Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Offside Rear wheel bearing has excessive play |2.6.2| | 1 |
Nearside Rear Front position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
Offside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Cross-member |6.1.B.2| | 1 |
Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Windscreen wiper not working (3.4 (a)) | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch next to crossmember |6.1.1 |c| |i|| | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch next to crossmember |6.1.1 |c| |i|| | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Inner chassis leg under the battery and inner wheel arch (5.3.6 (a) (i)) | 1 |
Horn not loud enough to be heard by another road user |1.6.2b| | 1 |
Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor (7.1.1 (a) (i)) | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill to floor (7.1.1 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
Nearside Front Brake pipe at imminent risk of failure or fracture x2 (1.1.11 (a)) | 1 |
Offside Front Brake pipe at imminent risk of failure or fracture x2 (1.1.11 (a)) | 1 |
Brake pipe at imminent risk of failure or fracture front to rear (1.1.11 (a)) | 1 |
Nearside Front Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing in 3 places (5.3.6 (a) (i)) | 1 |
Nearside Front Sub-frame corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Rear Direction indicator incorrect colour (1.4.A.2f) | 1 |
Offside Rear Direction indicator incorrect colour (1.4.A.2f) | 1 |
Offside Rear position lamp(s) adversely affected by the operation of another lamp (1.1.A.3f) | 1 |
Offside Stop lamp adversely affected by the operation of another lamp (1.2.1f) | 1 |
Offside Direction indicator adversely affected by the operation of another lamp (1.4.A.2h) | 1 |
Parking brake: efficiency below requirements (3.7.B.7) | 1 |
Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
Nearside Rear Direction indicator not working |4.4.1 |a| |ii|| | 1 |
Brake cable has restricted free movement |3.5.1k| | 1 |
Service brake: efficiency below requirements |3.7.C.1a| | 1 |
Offside Front Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill area.. |6.1.B.2| | 1 |
Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill area.. |6.1.B.2| | 1 |
Nearside Front Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill area.. |6.1.B.2| | 1 |
Offside Rear Lower Shock absorber has an excessively worn bush rear/rear |2.7.4| | 1 |
Nearside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
Offside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
Offside Rear Lower Shock absorber has an excessively worn bush rear/rear.. |2.7.4| | 1 |
Nearside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wing |6.1.1 |c| |i|| | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced strut top |6.1.1 |c| |i|| | 1 |
Offside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
Offside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded out rigger |2.4.A.3| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded under step |5.2.6| | 1 |
Hazard warning lamps inoperative |1.4.B.1b| | 1 |
Nearside Front Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded under sill / step |5.2.6| | 1 |
Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Nearside Rear Service brake grabbing severely (1.2.1 (c)) | 1 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Exhaust silencer insecure (8.1.1 (b) (i)) | 1 |
Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
front brake binding |3.7.B.1| | 1 |
front brake juddering severely |3.7.A.2b| | 1 |
Nearside Rear Body panel damaged and likely to cause injury lamp unit |6.2.1 |a| |i|| | 1 |
Rear Brake load sensing valve seized |3.6.E.3| | 1 |
Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Offside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Offside Front Electrical wiring likely to drag on the ground (4.11 (a) (iii)) | 1 |
Central Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Offside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Emissions not tested oil level too high. |7.4.B.1| | 1 |
Nearside Front Position lamp not working |4.2.1 |a|| | 1 |
Offside Rear Position lamp not working |4.2.1 |a|| | 1 |
Nearside Outer Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
Offside Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 1 |
Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
Offside Front Upper Brake pipe leaking |3.6.A.1| | 1 |
Nearside Front Headlamp insecure |1.7.3| | 1 |
Offside Front Headlamp insecure |1.7.3| | 1 |
Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Rear position lamp|s| insecure |1.1.A.3a| | 1 |
Nearside Headlamp insecure |1.7.3| | 1 |
Nearside Stop lamp has less than 50% of the light sources illuminating |1.2.1b| | 1 |
Nearside Front Exhaust system not adequately supported |7.1.1| | 1 |
Offside Front Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Rear Exhaust system not adequately supported |7.1.1| | 1 |
Offside Rear Exhaust system not adequately supported |7.1.1| | 1 |
Centre Front Fuel system component leaking |7.2.3| | 1 |
Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` wipers parking middle of screen |8.3.1b| | 1 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Front Upper Position lamp not working |4.2.1 |a|| | 1 |
Nearside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
Front Brake pipe leaking on a hydraulic braking system |1.1.11 |b| |ii|| | 1 |
Brake performance not tested |1.2.1 |g|| | 1 |
Power steering pipe/hose excessively corroded small pipes on steering rack (2.1.5 (g) (i)) | 1 |
Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Front Horn not working |7.7 |a| |ii|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wheel arch |5.3.6 |a| |i|| | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill end |7.1.1 |a| |i|| | 1 |
Front brake disc excessively pitted |3.5.1h| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced front cross member (6.1.1 (c) (i)) | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner/outer sills corroided |7.1.1 |a| |i|| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch by strut tunnel |5.3.6 |a| |i|| | 1 |
Nearside Front Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
Nearside Rear Seat belt retracting mechanism defective |5.2.5b| | 1 |
Offside Rear Seat belt retracting mechanism defective |5.2.5b| | 1 |
Brake pedal anti-slip provision missing |3.3.A.1b| | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under body (6.1.1 (c) (i)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under body sill (6.1.1 (c) (i)) | 1 |
Nearside Front Outer Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill (6.2.2 (d) (ii)) | 1 |
Offside Front Outer Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill (6.2.2 (d) (ii)) | 1 |
Nearside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced rigger (6.1.1 (c) (i)) | 1 |
Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced rigger (6.1.1 (c) (i)) | 1 |
Nearside Front Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
Offside Front Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
Exhaust emits excessive smoke or vapour likely to obscure the vision of other road users (8.2.2.2 (c)) | 1 |
Offside Rear Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
Nearside Front front brake binding |3.7.B.1| | 1 |
Offside Front Wheel bolt|s| missing |4.2.A.1e| | 1 |
Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Exhaust has a major leak of exhaust gases in 3 areas (6.1.2 (a)) | 1 |
Emissions not tested due to exhaust blow (8.2.2.2 (e)) | 1 |
Nearside Rear Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
Offside Rear Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Rear Leaf spring splayed and action impaired |2.4.B.1c| | 1 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 1 |
Centre Exhaust mounting missing |7.1.1b| | 1 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Offside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Windscreen wiper not operating automatically when switched on both front |8.2.1b| | 1 |
front brakes release unevenly |3.7.B.4| | 1 |
Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
Nearside Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Offside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Nearside Rear wheel bearing has excessive play |2.6.2| | 1 |
Offside Exhaust system not adequately supported |7.1.1| | 1 |
Centre Rear Parking brake lever has no reserve travel |3.1.6b| | 1 |
Steering system excessively tight |2.2.D.1| | 1 |
Offside Rear Rear fog lamp flickers when tapped lightly by hand |1.1.6d| | 1 |
Offside Rear Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
Nearside Front Direction indicators incorrect colour |1.4.A.2f| | 1 |
Offside Front Direction indicators incorrect colour |1.4.A.2f| | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wing under airbox (6.1.1 (c) (i)) | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced rear most outer sill (6.1.1 (c) (i)) | 1 |
Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 1 |
Power steering inoperative and steering adversely affected (2.1.5 (c) (ii)) | 1 |
Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
Power steering pipe/hose excessively corroded ALL (2.1.5 (g) (i)) | 1 |
Brake pipe leaking on a hydraulic braking system front (corroded/burst) (1.1.11 (b) (ii)) | 1 |
Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Emissions not tested (8.2.2.2 (e)) | 1 |
Nearside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength top strut mount inside arch (5.3.6 (a) (i)) | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 1 |
Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg next to engine mount (6.1.1 (c) (i)) | 1 |
Nearside Rear Upper Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Upper Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Rear Upper All position lamps not working |1.1.A.3b| | 1 |
Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Nearside Front All direction indicators incorrect colour |4.4.3 |a|| | 1 |
Offside Front All direction indicators incorrect colour |4.4.3 |a|| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sub frame |5.3.6 |a| |i|| | 1 |
Fuel tank leaking |6.1.3 |b| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Nearside Obligatory mirror missing (3.3 (a)) | 1 |
Exhaust system insecure 2 x rubbers missing and other rubbers perished (6.1.2 (a)) | 1 |
Offside Headlamp insecure (4.1.1 (c)) | 1 |
Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Offside Front Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 1 |
Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced SILL |7.1.1 |a| |i|| | 1 |
Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced SILL |7.1.1 |a| |i|| | 1 |
Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced SILL |7.1.1 |a| |i|| | 1 |
Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced SILL |7.1.1 |a| |i|| | 1 |
Nearside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength REAR OF ARCH |5.3.6 |a| |i|| | 1 |
Offside Upper Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Central Rear Exhaust emissions likely to be affected by an exhaust leak |8.2.2.1 |b|| | 1 |
Offside Front Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength SILL |5.3.6 |a| |i|| | 1 |
Offside Front Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength WHEEL ARCH |5.3.6 |a| |i|| | 1 |
Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
Nearside Rear An item not tested |Manual| | 1 |
Offside Rear An item not tested |Manual| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner wheelarch turret (5.3.6 (a) (i)) | 1 |
Fuel system component leaking |7.2.3| | 1 |
Parking brake lever has no reserve travel |3.1.6b| | 1 |
Offside Front Side repeater not working |1.4.A.2c| | 1 |
Offside Headlamp aim beam image kick up to the offside |1.8| | 1 |
Horn emits two or more alternating tones |1.6.2d| | 1 |
Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Nearside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
Offside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded inner and outer sill. |5.2.6| | 1 |
Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Fuel system component leaking excessively or a risk of fire |6.1.3 |b| |ii|| | 1 |
Offside Inner Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Exhaust emissions likely to be affected by an exhaust leak And down pipe bolts not seacure (8.2.1.1 (b)) | 1 |
Upper Steering column locking device insecure |2.1.6| | 1 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Emissions not tested exhaust holed to excess. |8.2.2.2 |e|| | 1 |
Rear Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
Nearside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Stop lamp not working |1.2.1b| | 1 |
Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Rear position lamp|s| adversely affected by the operation of another lamp COMPLETE LAMP |1.1.A.3f| | 1 |
Offside Rear Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
Offside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
Brake pipe leaking front to rear |3.6.A.1| | 1 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Headlamp aim beam image kick up to the offside both |1.8| | 1 |
Headlamp levelling device inoperative both |4.1.5 |a|| | 1 |
Offside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
Offside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Emissions not tested Blocked smoke tester twice (8.2.2.2 (e)) | 1 |
Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
Offside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
Rear Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 1 |
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer, lower mounting (7.1.1 (a) (i)) | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer, lower mounting (7.1.1 (a) (i)) | 1 |
Offside Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
Nearside Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
Offside Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
Nearside Front Inner Suspension component mounting prescribed area is excessively corroded arch |2.4.A.3| | 1 |
Offside Front Inner Suspension component mounting prescribed area is excessively corroded arch |2.4.A.3| | 1 |
Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Rear position lamp|s| incorrect colour |1.1.A.3e| | 1 |
Nearside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Offside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill/corner of cab |7.1.1 |a| |i|| | 1 |
Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Nearside Rear Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
Rear Direction indicators incorrect colour |1.4.A.2f| | 1 |
Hazard warning switch faulty |1.4.B.1d| | 1 |
Front Direction indicators adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
Rear Direction indicators adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
Nearside Front Brake pipe fouled by moving parts |3.6.B.2a| | 1 |
Nearside Rear wheel bearing rough when rotated |2.6.1| | 1 |
Emissions not tested |7.0| | 1 |
Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Driver`s seat insecure |6.2.A.1| | 1 |
Exhaust catalytic converter missing where one was fitted as standard |7.1.3| | 1 |
Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
Offside Front Brake pipe fouled by moving parts |3.6.B.2a| | 1 |