Most common failures | No# failures |
---|
Registration plate lamp issues | 6 |
Headlamp aim out of alignment | 5 |
Offside Headlamp not working on dipped beam |1.7.5a| | 3 |
Offside Headlamp not working on main beam |1.7.5a| | 2 |
Parking brake: efficiency below requirements |3.7.B.7| | 2 |
Offside Front Side repeater not working |1.4.A.2c| | 1 |
Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
Direction indicators not working |1.4.A.2c| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Side repeater not working |1.4.A.2c| | 1 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
Parking brake lever has no reserve travel |3.1.6b| | 1 |
Offside Rear Stop lamp not working |1.2.1b| | 1 |
Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Headlamp switch faulty |1.7.1| | 1 |
Offside front brake binding |3.7.B.1| | 1 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Brake pipe excessively corroded | 1 |
Offside Front Suspension arm locating pin retaining device not properly locked Lower ball joint shank retaining lock nut not through nyloc securing material. |2.4.G.3b| | 1 |
Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
Offside Front Direction indicator missing |1.4.A.2b| | 1 |
Horn not working |1.6.2a| | 1 |
Rear Brake load sensing valve has been disconnected and was fitted as standard Rear brake compensator bypassed. |3.6.E.2| | 1 |
Offside Front Lower Ball joint ball pin shank loose Locking retaining nut nyloc not screwed downed to thread. |2.2.B.1c| | 1 |
Nearside Front Inner Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt Centre drag link gaiter split. |2.2.C.1c| | 1 |
Offside Front Inner Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt Offside end of centre drag link gaiter split. |2.2.C.1c| | 1 |
Nearside Front Inner Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt Outer track rod inner end gaiter split, |2.2.C.1c| | 1 |
Offside Front Inner Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt Offside track rod inner end gaiter split. |2.2.C.1c| | 1 |
Nearside Front Inner Suspension arm has excessive play in a pin/bush Lower suspension arm inner end. |2.4.G.2| | 1 |
Offside Front Inner Suspension arm has excessive play in a pin/bearing Lower suspension arm inner bush. |2.4.G.2| | 1 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Stop lamp not working |1.2.1b| | 1 |
Rear parking brake recording little or no effort | 1 |