| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 40 |
| Registration plate issues | 20 |
| Exhaust is leaking and excessively noisey |7.1.1b| | 9 |
| Offside Front shock absorber seal failed and leaking oil |2.3.3| | 8 |
| Nearside Front shock absorber seal failed and leaking oil |2.3.3| | 7 |
| Rear reflector on motorcycle missing |1.4.1| | 6 |
| Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 5 |
| Exhaust excessively deteriorated |7.1.1a| | 5 |
| Exhaust noise is clearly in excess of that emitted by a similar motor bicycle fitted with a standard silencer in average condition |7.1.2| | 5 |
| Front position lamp does not illuminate immediately when switched on |1.1.3a| | 4 |
| Front wheel bearings have excessive free play |2.3.5b| | 4 |
| Throttle operating incorrectly |6.2.1f| | 4 |
| Offside Rear Direction indicator not working |1.5.1c| | 3 |
| Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 3 |
| Nearside Front Shock absorber has a serious fluid leak |5.3.2 |b|| | 3 |
| Throttle has a significant change in engine speed whilst moving the steering from lock to lock |2.1.4| | 3 |
| Front Front wheel bearings have excessive free play |2.3.5b| | 3 |
| Direction indicators flashing more than 120 times per minute |1.5.1c| | 3 |
| Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 3 |
| Front shock absorber seal failed and leaking oil |2.3.3| | 3 |
| Nearside Handlebar handgrip not secure to handlebars. |2.1.1c| | 3 |
| Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 3 |
| Rear Brake locking device missing |3.2.A1e| | 2 |
| Rear wheel spindle securing nut locking device missing |2.4.A.2b| | 2 |
| Offside Front Front shock absorber seal failed and leaking oil |2.3.3| | 2 |
| Front suspension has inadequate damping effect. |2.3.6c| | 2 |
| Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 2 |
| Offside Brake disc|s| friction surface contaminated by oil or grease |3.2.A1k| | 2 |
| Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 2 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Nearside Front Brake component leaking fluid |3.2.B4| | 2 |
| Rear Exhaust noise is clearly in excess of that emitted by a similar motor bicycle fitted with a standard silencer in average condition |7.1.2| | 2 |
| Nearside Front Handlebar handgrip not secure to handlebars. |2.1.1c| | 2 |
| Rear Rear reflector on motorcycle missing |1.4.1| | 2 |
| Front Brake lever has inadequate reserve travel |3.1.3b| | 2 |
| Stop lamp remains on when the brakes are released | 2 |
| Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Offside Front Brake disc|s| friction surface contaminated by oil or grease |3.2.A1k| | 2 |
| Front Brake disc|s| friction surface contaminated by oil or grease |3.2.A1k| | 2 |
| Steering headbearing has excessive free play |2.2.2| | 2 |
| Front Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 2 |
| Front Valve stem seriously damaged (5.2.3 (j)) | 2 |
| Rear reflector missing (4.8.2 (a) (ii)) | 2 |
| Front Shock absorber has a serious fluid leak (5.3.2 (b)) | 2 |
| Nearside Front Shock absorber has a serious fluid leak (5.3.2 (b)) | 2 |
| Stop lamp not working Foot control (4.3.1 (a) (ii)) | 2 |
| Rear reflector on motorcycle insecure |1.4.2c| | 1 |
| Horn not working |7.7 |a| |ii|| | 1 |
| Nearside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
| Offside Front Direction indicator flashing more than 120 times per minute |1.5.1c| | 1 |
| Front All position lamps do not illuminate immediately when switched on |1.1.3a| | 1 |
| Nearside Rear Shock absorber likely to become detached |5.3.2 |a| |ii|| | 1 |
| Offside Rear Shock absorber insecurely attached |5.3.2 |a| |i|| | 1 |
| Motorcycle structure joining/attachment plate or fastening insecure Steering stem nut |6.1.1 |b| |i|| | 1 |
| Rear Suspension arm pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Inner Indicator tell tale not functioning |1.5.2| | 1 |
| Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
| Direction indicator flashing more than 120 times per minute All indicators |1.5.1c| | 1 |
| Front Lower Steering headbearing has excessive free play |2.2.2| | 1 |
| Nearside Front Footrest insecure |6.2.1a| | 1 |
| Offside Rear Footrest insecure |6.2.1a| | 1 |
| Offside Front Direction indicator not working |4.4.1 |a| |ii|| | 1 |
| Steering movement excessively stiff with the weight on the lower bearing |2.2.1a| | 1 |
| Steering movement excessively stiff with the wheel raised |2.2.1b| | 1 |
| Rear Roller brake test indicates a sticking brake |3.3.A1a| | 1 |
| Centre Exhaust is leaking and excessively noisey |7.1.1b| | 1 |
| Rear wheel rotation likely to be impeded |6.2.1b| | 1 |
| Stop lamp remains on when the brake is released Rear brake |1.3.1e| | 1 |
| Rear reflector on motorcycle obscured |1.4.2b| | 1 |
| Outer Rear Rear reflector on motorcycle missing |1.4.1| | 1 |
| Headlamp insecure |1.7.3| | 1 |
| Direction indicators flashing more than 120 times a minute |1.4.A.2g| | 1 |
| Offside Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Position lamp switch faulty |1.1.4a| | 1 |
| Rear Riders seat insecure |6.2.1a| | 1 |
| Centre Rear Exhaust is leaking and excessively noisey |7.1.1b| | 1 |
| Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 1 |
| Front Throttle has a significant change in engine speed whilst moving the steering from lock to lock |2.1.4| | 1 |
| Front Floor brake test indicates a binding brake |3.3.C2c| | 1 |
| Fuel cap does not fasten securely by a positive means |7.2.2b| | 1 |
| Rear Brake pedal cannot be released smoothly |3.1.3d| | 1 |
| Rear Floor brake test indicates a sticking brake |3.3.C2c| | 1 |
| Rear position lamp incorrect colour |1.1.2b| | 1 |
| Fuel cap does not fasten securely maintaining the sealing arrangement |7.2.2b| | 1 |
| Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Steering movement excessively `notchy` with the wheel raised |2.2.1b| | 1 |
| Front Brake disc contaminated |1.1.14 |b|| | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Nearside Rear Shock absorber insecure |2.7.2b| | 1 |
| Vehicle structure fractured seriously affecting its strength within 30cm of towbar mounting |6.6.6| | 1 |
| Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Rear Brake pipe inadequately supported |3.6.B.1| | 1 |
| Offside Front Fluid suspension unit leaking |2.4.D.2| | 1 |
| Nearside Front Fluid suspension unit leaking |2.4.D.2| | 1 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Rear Brake pedal actuating lever has abnormal movement indicating maladjustment or excessive wear |3.3.A.1h| | 1 |
| Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Nearside Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside Brake reaction bracket insecure |3.2.A1j| | 1 |
| Offside Front wheel spindle securing nut locking device missing |2.3.5a| | 1 |
| Rear Rear wheel spindle securing nut locking device missing |2.4.A.2b| | 1 |
| Nearside Rear shock absorber insecurely mounted |2.4.A.3b| | 1 |
| Front Roller brake test indicates a binding brake |3.3.A1a| | 1 |
| Offside Rear position lamp deteriorated and function impaired |1.1.1b| | 1 |
| Riders seat insecure |6.2.1a| | 1 |
| Rear wheel bearings have excessive free play |2.4.A.2c| | 1 |
| Front Steering headbearing has excessive free play |2.2.2| | 1 |
| Front Brake master cylinder leaking |1.1.10 |b| |ii|| | 1 |
| Nearside Front Brake disc|s| friction surface contaminated by oil or grease |3.2.A1k| | 1 |
| Rear Indicator switch does not operate the direction indicators on the side selected |1.5.4| | 1 |
| Front Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 1 |
| Rear suspension bearing has excessive free play |2.4.A2a|i|| | 1 |
| Nearside Front Brake lining|s| contaminated by oil or grease |3.2.A1k| | 1 |
| Front Brake disc|s| has excessive run out |3.2.A1m| | 1 |
| Rear Front wheel bearings have excessive free play |2.3.5b| | 1 |
| Brake lever insecure |3.1.2a| | 1 |
| Headlamp aim headlamp damaged and function impaired |1.2.3a| | 1 |
| Front Front position lamp does not illuminate immediately when switched on |1.1.3a| | 1 |
| Front Horn not working |1.7.3a| | 1 |
| Rear Exhaust markings indicating not for road use or similar wording |7.1.4| | 1 |
| Nearside Front Direction indicator not working |1.5.1c| | 1 |
| Centre Front Front wheel bearings are excessively rough |2.3.5b| | 1 |
| Offside Rear Direction indicators not working |1.5.1c| | 1 |
| Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
| Nearside Front Brake disc|s| cracked |3.2.A1g| | 1 |
| Rear Brake lining|s| less than 1.5 mm thick |3.2.A1f|i|| | 1 |
| Offside Front Upper Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
| Rear All position lamps adversely affected by the operation of another lamp |1.1.3b| | 1 |
| Rear Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
| Lower Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
| Rear Motorcycle structure excessively corroded around center stand area |6.1.1a| | 1 |
| Front Front suspension has inadequate damping effect. |2.3.6c| | 1 |
| Rear Rear wheel spindle securing nut|s| loose |2.4.A.2b| | 1 |
| Rear Brake reaction bracket securing bolt|s| loose |3.2.A1j| | 1 |
| Offside Front Shock absorber has a serious fluid leak |5.3.2 |b|| | 1 |
| Nearside Front Brake disc|s| has excessive run out |3.2.A1m| | 1 |
| Offside Front Brake disc|s| has excessive run out |3.2.A1m| | 1 |
| Headlamp dipped beam affected by the operation of another lamp |1.2.2c| | 1 |
| Front Stop lamp remains on when the brake is released |1.3.1e| | 1 |
| Horn not loud enough to be heard by another road user |1.7.3a| | 1 |
| Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
| Front Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
| Rear Roller brake test indicates a severely grabbing brake |3.3.A1b| | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Steering linkage locking device missing in rear brake rod nut (2.1.3 (d)) | 1 |
| Steering headbearing in such a condition that steering control is adversely affected (2.2.2 (f) (ii)) | 1 |
| Front Shock absorber has negligible damping effect (5.3.2 (b)) | 1 |
| Rear Brake excessively binding (1.2.1 (f)) | 1 |
| Front Brake master cylinder leaking (1.1.10 (b) (ii)) | 1 |
| Rear Stop lamp not working (4.3.1 (a) (ii)) | 1 |
| Throttle control functioning such that safe operation of the motorcycle is adversely affected (6.2.7 (a) (ii)) | 1 |
| Rear Upper Exhaust has a major leak of exhaust gases Rear exhaust holed (6.1.2 (a)) | 1 |
| All direction indicators missing (4.4.1 (a) (ii)) | 1 |
| Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Front Position lamp not working (4.2.1 (a)) | 1 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Front Brake lagging in operation (1.2.1 (d)) | 1 |
| Rear Wheel bearing has excessive play rear wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Rear Shock absorber has negligible damping effect (5.3.2 (b)) | 1 |
| Rear Brake component inadequately mounted Split pin missing rear torque arm - Replaced for new (1.1.21 (c)) | 1 |
| Front Brake disc contaminated (1.1.14 (b)) | 1 |
| Registration plate lamp issues | 1 |
| Offside Handlebar grip insecure to handlebar (2.2.1 (d) (ii)) | 1 |
| Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii)) | 1 |
| Central Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |