Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 24 |
Headlamp aim out of alignment | 22 |
Anti-lock braking system warning lamp indicates an ABS fault | 18 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 11 |
Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 10 |
Horn not working (7.7 (a)) | 9 |
Emissions not tested (8.2.1.2 (d)) | 9 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 8 |
Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 8 |
Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 7 |
Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 7 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 6 |
Registration plate lamp issues | 6 |
Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
Brakes imbalanced across an axle | 6 |
Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 5 |
Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 4 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 4 |
Windscreen washer not working | 4 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 4 |
Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 4 |
Nearside Side repeater not working (4.4.1 (a) (ii)) | 4 |
Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 4 |
Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 4 |
Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 4 |
Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 4 |
Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 4 |
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 4 |
Brake hose excessively deteriorated | 4 |
Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 4 |
Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 3 |
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
Offside Side repeater not working (4.4.1 (a) (ii)) | 3 |
Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
Exhaust emits dense blue smoke at idle (8.2.1.2 (f)) | 3 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 3 |
Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 3 |
Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 3 |
Brake lever has insufficient reserve travel (1.1.2 (a)) | 3 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
Offside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 3 |
Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 3 |
Offside Front Side repeater not working (4.4.1 (a) (ii)) | 3 |
Nearside Rear Direction indicator incorrect colour (4.4.3 (a)) | 2 |
Nearside Rear Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 2 |
Exhaust catalytic converter missing where one was fitted as standard (8.2.1.1 (a)) | 2 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 2 |
Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 2 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
Oil leaking excessively from engine (8.4.1 (a) (i)) | 2 |
All direction indicators not working (4.4.1 (a) (ii)) | 2 |
Electronic braking system warning device indicates a fault (1.7 (b)) | 2 |
Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 2 |
Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 2 |
Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
Nearside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
Nearside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
Rear Service brake excessively fluctuating (1.2.1 (e)) | 2 |
Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 2 |
Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 2 |
Exhaust Lambda reading after 2nd fast idle outside specified limits Lowest reading 1.5, Max=.970 (8.2.1.2 (c)) | 1 |
Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Fuel system component leaking petrol filter (6.1.3 (b) (i)) | 1 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area (5.3.6 (a) (i)) | 1 |
Electronic stability control warning lamp indicates a fault (7.12 (e)) | 1 |
Nearside Rear Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
Offside Rear Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
Nearside Rear Sub-frame pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Sub-frame pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Lower Suspension arm ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
Offside Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
Power steering component leaking Around rack area (2.1.5 (a)) | 1 |
Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits .36 (8.2.1.2 (a)) | 1 |
Exhaust Lambda reading after 2nd fast idle outside specified limits 1.177 (8.2.1.2 (c)) | 1 |
Offside Rear Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting central jacking point (6.2.2 (d) (i)) | 1 |
Horn sound not in accordance with requirements (7.7 (c)) | 1 |
Headlamp aim projected beam image is obviously incorrect both (4.1.2 (c)) | 1 |
Offside Front Lower Suspension arm ball joint excessively worn outer (5.3.4 (a) (i)) | 1 |
Side repeater not working off side front (4.4.1 (a) (ii)) | 1 |
Suspension arm ball joint dust cover no longer prevents the ingress of dirt near side front lower arm (5.3.4 (b) (ii)) | 1 |
Suspension arm ball joint dust cover no longer prevents the ingress of dirt off side front lower arm (5.3.4 (b) (ii)) | 1 |
Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt off side front (2.1.3 (g) (ii)) | 1 |
Service brake excessively binding off side front (1.2.1 (f)) | 1 |
Service brake excessively binding off side rear (1.2.1 (f)) | 1 |
Other passenger door cannot be opened from outside the vehicle near side rear (6.2.3 (a)) | 1 |
Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Front Brake disc significantly and obviously worn pair (1.1.14 (a) (i)) | 1 |
Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt outer cv gaiter deteriorated/ perished+ split +leaking grease (6.1.7 (g) (ii)) | 1 |
Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt outer cv gaiter insecure/excessive grease leaks (6.1.7 (g) (ii)) | 1 |
Exhaust emits excessive dense blue smoke during acceleration (8.2.1.2 (g)) | 1 |
Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength subframe bracket (5.3.6 (a) (i)) | 1 |
Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
Offside Rear Inner Brake disc in such a condition that it is seriously weakened (1.1.14 (a) (ii)) | 1 |
Headlamp not working on dipped beam both sides (4.1.1 (a) (ii)) | 1 |
Brake performance not tested (1.2.1 (g)) | 1 |
Front Prop shaft joint constant velocity boot no longer prevents the ingress of dirt both (6.1.7 (g) (ii)) | 1 |
Brake servo defective or ineffective (1.1.10 (a) (i)) | 1 |
Fuel system component leaking fuel filter (6.1.3 (b) (i)) | 1 |
Speedometer clearly inoperative (7.8 (b) (ii)) | 1 |
Rear Exhaust system insecure (6.1.2 (a)) | 1 |
Stop lamp(s) light intensity significantly reduced all (4.3.3 (a) (ii)) | 1 |
Fuel cap/sealing device component leaking tank to filler pipe (6.1.3 (b) (i)) | 1 |
Offside Front Sub-frame insecure and impairing directional stability bolt missing (5.3.3 (a) (ii)) | 1 |
Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Nearside Rear Seat belt not functioning as intended (7.1.2 (c)) | 1 |
Nearside Rear Passengers seat backrest cannot be secured in the upright position. (6.2.6 (a) (i)) | 1 |
Offside Front Anti-roll bar linkage ball joint excessively worn Upper Dust Cover Split (5.3.4 (a) (i)) | 1 |
Fuel system component leaking Fuel Filter (6.1.3 (b) (i)) | 1 |
Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Offside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
Offside Front Lower Suspension arm pin or bush excessively worn Wishbone rear bush (5.3.4 (a) (i)) | 1 |
Offside Front Service brake lagging in operation (1.2.1 (d)) | 1 |
Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Offside Rear Sub-frame attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 1 |
Emissions not tested vehicle losing water (8.2.1.2 (d)) | 1 |
Headlamp not working on dipped beam offside and nearside (4.1.1 (a) (ii)) | 1 |
Headlamp not working on main beam offside and nearside (4.1.1 (a) (ii)) | 1 |
Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
Offside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
Nearside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
Headlamp aim projected beam image is obviously incorrect offside & nearside (4.1.2 (c)) | 1 |
Electronic stability control switch not functioning correctly (7.12 (d)) | 1 |
Offside Rear Suspension arm attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
Nearside Rear Suspension arm attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
Rear Lower Suspension arm pin or bush excessively worn offside & nearside (5.3.4 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Nearside Rear Inner Suspension arm pin or bush excessively worn radius arm (5.3.4 (a) (i)) | 1 |
Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
Offside Front Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
Emissions not tested LOW FUEL (8.2.1.2 (d)) | 1 |
Headlamp not working on dipped beam Both (4.1.1 (a) (ii)) | 1 |
Headlamp not working on main beam Both (4.1.1 (a) (ii)) | 1 |
All position lamps adversely affected by the operation of another lamp All position lamps turn off when the headlamp switch is turned to the "headlamps on" position (4.2.3 (c)) | 1 |
Headlamp aim not tested (4.1.2 (b)) | 1 |
Nearside Rear Shock absorbers has an excessively worn bush upper bush (5.3.2 (c)) | 1 |
Offside Rear Shock absorbers has an excessively worn bush upper bush (5.3.2 (c)) | 1 |
Offside Rear Shock absorbers has a serious fluid leak | 1 |
Fuel cap/sealing device missing (6.1.3 (b) (i)) | 1 |
Offside Rear Suspension arm attachment bracket/mounting fractured rear axle arm inner bush housing cracked (5.3.3 (b) (ii)) | 1 |
Nearside Headlamp reflector seriously defective (4.1.1 (b) (ii)) | 1 |
Offside Headlamp reflector seriously defective (4.1.1 (b) (ii)) | 1 |
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Rear Coil spring corroded so that its cross sectional area is reduced and seriously weakened X2 (5.3.1 (b) (i)) | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt split/leaking grease (2.1.3 (g) (ii)) | 1 |
Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
Nearside Side repeater incorrect colour (4.4.3 (a)) | 1 |
Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Rear Lower Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
Nearside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
Offside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
Nearside Front Shock absorbers insecurely attached (5.3.2 (a) (i)) | 1 |
Offside Front Shock absorbers insecurely attached (5.3.2 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Rear beam bush bracket (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded (7.1.1 (a) (i)) | 1 |
Offside Rear Vehicle structure is fractured and so weakened within 30cm of a towbar mounting, the towbar is likely to become detached (6.1.6 (i) (ii)) | 1 |
Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength axle mount (5.3.6 (a) (i)) | 1 |
Nearside Front Coil spring insecure Not positioned correctly (5.3.1 (a) (i)) | 1 |
Fuel pipe insecure (6.1.3 (a) (i)) | 1 |
Nearside Rear Suspension arm pin or bush likely to become detached axle beam (5.3.4 (a) (ii)) | 1 |
Brake disc in such a condition that it is seriously weakened all round (1.1.14 (a) (ii)) | 1 |
Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 1 |
Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Front Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
Rear Exhaust silencer insecure (8.1.1 (b) (i)) | 1 |
Offside Rear Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
Offside Front Inner Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Nearside Front Lower Suspension arm pin or bush excessively worn front bush worn (5.3.4 (a) (i)) | 1 |
Offside Front Lower Suspension arm pin or bush excessively worn front bush worn (5.3.4 (a) (i)) | 1 |
Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Nearside Front Brake hose damaged and likely to fail (1.1.12 (a)) | 1 |
Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Front Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
Nearside Rear Suspension arm pin or bush excessively worn Trailing arm worn (5.3.4 (a) (i)) | 1 |
Offside Rear Suspension arm pin or bush excessively worn Trailing arm worn (5.3.4 (a) (i)) | 1 |
Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
Nearside Rear Shock absorbers has a serious fluid leak | 1 |
Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
Nearside Front Outer Anti-lock braking system component excessively damaged abs ring broken and effecting braking (1.6 (e)) | 1 |
Nearside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Central Front Upper Engine mounting damaged or deteriorated resulting in excessive movement (6.1.8 (a) (i)) | 1 |
Central Rear Seat belt not functioning as intended (7.1.2 (c)) | 1 |
Exhaust emits visible black smoke at idle (8.2.1.2 (f)) | 1 |
Fluid leak harmful to the environment or a risk to other road users coolant (8.4.1 (a) (i)) | 1 |
Nearside Rear Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
Offside Rear Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
Registration plate issues | 1 |
Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 1 |
Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt insecure (6.1.7 (g) (ii)) | 1 |
Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Nearside Front Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
Nearside Rear Anti-roll bar linkage attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 1 |
Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |