Most common failures | No# failures |
---|
Brakes imbalanced across an axle | 6 |
Brake hose excessively deteriorated | 5 |
Registration plate lamp issues | 3 |
Parking brake: efficiency below requirements |3.7.B.7| | 3 |
Windscreen washer not working | 2 |
Indicator switch insecure |1.4.A.1| | 2 |
Windscreen wiper does not clear the windscreen effectively | 2 |
Headlamp aim out of alignment | 2 |
Rear parking brake recording little or no effort | 2 |
Nearside Headlamp not working on main beam |1.7.5a| | 2 |
Steering system excessively tight |2.2.D.1| | 2 |
Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Nearside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Offside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Steering arm has relative movement at its fixings |2.2.B.1h| | 1 |
Nearside Stop lamp not working |1.2.1b| | 1 |
Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
Offside Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
Nearside Rear Position lamp not working |4.2.1 |a|| | 1 |
Offside Rear Position lamp not working |4.2.1 |a|| | 1 |
Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
Horn not working |7.7 |a| |ii|| | 1 |
Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
Nearside Parking brake inoperative on one side |1.4.1 |a|| | 1 |
Offside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 1 |
Front Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
All position lamps not working |4.2.1 |a|| | 1 |
Offside Rear Shock absorbers has a serious fluid leak | 1 |
Nearside Front Floor excessively deteriorated |6.2.4 |a| |i|| | 1 |
Brake pipe excessively chafed |3.6.B.2c| | 1 |
Registration plate issues | 1 |
Front Passenger`s seat insecure |6.2.A.1| | 1 |
Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
Offside Front Statutory seat belt missing |5.1.1| | 1 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Steering system has excessive free play detected at the steering wheel |steering box fitted| |2.2.A.1a| | 1 |
Nearside Front Statutory seat belt missing |5.1.1| | 1 |
Offside Steering system has a road wheel fouling a part of the vehicle |2.2.D.2a| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is severely distorted |2.4.A.3| | 1 |
Nearside Front passenger seat insecure |6.2.3| | 1 |
Indicator tell tale inoperative |1.4.A.2a| | 1 |
Parking brake lever has no reserve travel |3.1.6b| | 1 |
Horn not working |1.6.2a| | 1 |
Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
Nearside Rear Brake lining|s| less than 1.5 mm thick |3.5.1g| | 1 |
Nearside Front Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Front brake application uneven | 1 |
Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
Rear brake application uneven | 1 |
Rear brake binding | 1 |