Most common failures | No# failures |
---|
Headlamp aim out of alignment | 10 |
Windscreen wiper does not clear the windscreen effectively | 9 |
Registration plate issues | 6 |
Registration plate lamp issues | 5 |
Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 4 |
Nearside Headlamp aim beam image kick up to the offside |1.8| | 3 |
Offside Headlamp aim beam image kick up to the offside |1.8| | 3 |
Nearside Rear Shock absorbers has a serious fluid leak | 3 |
Offside Rear Rear fog lamp not working |1.3.2b| | 3 |
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 3 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 3 |
Brake pedal has insufficient reserve travel (1.1.2 (a)) | 3 |
Nearside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Brakes imbalanced across an axle | 2 |
Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
Brake hose excessively deteriorated | 2 |
Nearside Rear Stop lamp not working |1.2.1b| | 2 |
Offside Rear Stop lamp not working |1.2.1b| | 2 |
Offside Rear Shock absorbers has a serious fluid leak | 2 |
Engine MIL inoperative or indicates a malfunction |8.2.2.2 |g|| | 2 |
Engine MIL inoperative or indicates a malfunction (8.2.2.2 (g)) | 2 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Parking brake: efficiency below requirements |3.7.B.7| | 2 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
Rear Mechanical brake component has restricted free movement | 2 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 2 |
Windscreen washer not working | 2 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Brake pedal spongy |3.3.B.1b| | 2 |
Rear fog lamp not working |1.3.2b| | 2 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
Offside Rear fog lamp missing |1.3.2a| | 1 |
Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Nearside Front Shock absorbers has a serious fluid leak | 1 |
Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Nearside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Front Side repeater not working |1.4.A.2c| | 1 |
Offside Front Side repeater not working |1.4.A.2c| | 1 |
Engine MIL inoperative or indicates a malfunction |8.2.1.2 |h|| | 1 |
Offside Headlamp lens seriously defective / nearside |4.1.1 |b| |ii|| | 1 |
Offside Front Suspension arm pin or bush excessively worn inner |5.3.4 |a| |i|| | 1 |
Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover missing (5.3.4 (b) (ii)) | 1 |
Offside Rear position lamp|s| adversely affected by the operation of another lamp / n/s with stop lights |1.1.A.3f| | 1 |
Offside Suspension arm has excessive play in a pin/bush and nearside front rearmost |2.4.G.2| | 1 |
Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Rear Body component damaged and likely to cause injury light unit (6.2.1 (a) (i)) | 1 |
Offside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Lower Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Service brake is causing the vehicle to swerve to the nearside (1.2.1 (b) (i)) | 1 |
Nearside Front Inner Prop shaft joint constant velocity boot no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Nearside Front Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
Offside Rear Direction indicator adversely affected by the operation of another lamp (4.4.3 (b)) | 1 |
Offside Front Body component corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
Offside Front Cab steps in such a condition that it is likely to cause injury (6.2.8 (b)) | 1 |
Nearside Side repeater not working |1.4.A.2c| | 1 |
Offside Side repeater not working |1.4.A.2c| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Rear brake binding | 1 |
Nearside Headlamp insecure |1.7.3| | 1 |
Nearside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Braking system leaking Brake Servo Pipe |3.6.A.1| | 1 |
Nearside Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt x 2 (2.1.3 (g) (ii)) | 1 |
Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
Nearside Stop lamp not working |1.2.1b| | 1 |
Offside Stop lamp not working |1.2.1b| | 1 |
Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
Anti-lock braking system warning lamp indicates an ABS fault | 1 |
Parking brake lever has no reserve travel |3.1.6b| | 1 |
Nearside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
Nearside Front Macpherson strut damaged and seriously weakened bearing damaged by broken coil spring and in 2 parts (5.3.3 (b) (i)) | 1 |
Nearside Rear Service brake excessively binding unable to check wheel bearing for roughness (1.2.1 (f)) | 1 |
Offside Side repeater with a multiple light source more than 1/2 not functioning (4.4.1 (a) (ii)) | 1 |
Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement rear bush |2.4.G.2| | 1 |
Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
Steering system has excessive free play detected at the steering wheel |steering box fitted| |2.2.A.1a| | 1 |
Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Nearside Front Direction indicator not working side indicator |4.4.1 |a| |ii|| | 1 |
Offside Front Lower Shock absorbers insecurely attached |5.3.2 |a| |i|| | 1 |
Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Brake pedal creeps down under servo assistance and touches the floor |3.3.C.3| | 1 |
Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
Brake pedal has no servo assistance |3.3.B.2| | 1 |
Offside Front Direction indicator not working |1.4.A.2c| | 1 |
Horn not working |1.6.2a| | 1 |
Rear fog lamp tell tale missing |1.3.1b| | 1 |
Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Front Lower Steering pivot point has excessive play |2.2.B.1g| | 1 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Rear fog lamp insecure |1.3.2a| | 1 |
Nearside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
Horn not working (7.7 (a)) | 1 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Offside Front Inner Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Front Position lamp not working |4.2.1 |a|| | 1 |
Offside Front coil spring broken |2.4.C.1a| | 1 |
Nearside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Offside Front Seat belt buckle not functioning as intended |7.1.2 |d|| | 1 |
Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 1 |
Electronic stability control warning lamp indicates a fault (7.12 (e)) | 1 |
Nearside Rear Seat belt not functioning as intended (7.1.2 (c)) | 1 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Front Headlamp insecure |1.7.3| | 1 |
Nearside Front Headlamp aim not tested |1.8.A.1c| | 1 |
Offside Side repeater has less than 50% of the light sources illuminating |1.4.A.2c| | 1 |
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Nearside Headlamp aim not tested not working (4.1.2 (b)) | 1 |
Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Upper Torque/reaction arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturer`s specified limits |8.2.1.2 |a|| | 1 |
Exhaust carbon monoxide content at idle exceeds manufacturer`s specified limits |8.2.1.2 |b|| | 1 |
Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 1 |