| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 20 |
| Brake hose excessively deteriorated | 18 |
| Registration plate lamp issues | 15 |
| Headlamp aim out of alignment | 12 |
| Rear parking brake recording little or no effort | 9 |
| Parking brake: efficiency below requirements |3.7.B.7| | 8 |
| Windscreen wiper does not clear the windscreen effectively | 7 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
| Horn not working (7.7 (a)) | 5 |
| Rear brake binding | 5 |
| Registration plate issues | 4 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 4 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 4 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 4 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 3 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 3 |
| Front Horn not working |1.6.2a| | 3 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Horn not working (7.7 (a) (ii)) | 3 |
| Brakes imbalanced across an axle | 3 |
| Nearside Stop lamp not working |1.2.1b| | 3 |
| Offside Steering rack gaiter split |2.2.D.2d| | 3 |
| Rear brake application uneven | 3 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Offside Rear fog lamp not working |1.3.2b| | 2 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Front Brake pipe excessively chafed |3.6.B.2c| | 2 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Horn not working |1.6.2a| | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 2 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 2 |
| Offside Rear Braking system leaking |3.6.A.1| | 2 |
| Windscreen washer not working | 2 |
| Windscreen wiper not working (3.4 (a)) | 2 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Nearside Headlamp incorrect colour (4.1.4 (a)) | 2 |
| Offside Headlamp incorrect colour (4.1.4 (a)) | 2 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Offside Rear Shock absorbers has a serious fluid leak | 1 |
| Offside Body panel damaged and likely to cause injury (6.2.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Seat belt not functioning as intended rear seat belts jammed under seats (7.1.2 (c)) | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Nearside Front Upper Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch. (5.3.6 (a) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch/b pillar close to jacking & body mounts (6.2.2 (d) (i)) | 1 |
| Engine mounting bracket damaged or deteriorated resulting in excessive movement (6.1.8 (a) (i)) | 1 |
| Rear fog lamp switch missing |1.3.1a| | 1 |
| Rear fog lamp tell tale missing |1.3.1b| | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis leg as marked |5.3.6 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floorpan / arch areas holed by seat belt mount |5.2.6| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded floorpan areas holed by seat belt mount |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill areas holed |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill areas holed |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded underwing forward lower section holed |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded underwing forward lower section holed by suspension arm forward bracket |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded underfloor corner box sections holed |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded underfloor corner box sections holed |2.4.A.3| | 1 |
| Nearside Front Lower Suspension arm corroded and seriously weakened holed |2.4.G.1| | 1 |
| Nearside Rear Fuel hose insecure |7.2.1| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area is excessively corroded wheel arch and outer sill |5.2.6| | 1 |
| Offside Front Inner Seat belt anchorage prescribed area is excessively corroded wheel arch and outer sill |5.2.6| | 1 |
| Nearside Rear Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Rear Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
| Rear Fuel system component insecure fuel pipe insecure and fouling suspension |7.2.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` items on interior mirror |8.3.1e| | 1 |
| Offside Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Offside Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Nearside Front Upper Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear coil spring broken |2.4.C.1a| | 1 |
| Offside Rear coil spring broken |2.4.C.1a| | 1 |
| Nearside Front Steering retaining device missing track rod end castle nut |2.2.C.1g| | 1 |
| Offside Front Steering retaining device missing track rod end castle nut |2.2.C.1g| | 1 |
| Braking system leaking |3.6.A.1| | 1 |
| Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Floor in such a condition it is likely to cause loss of control of the vehicle Holed by corrosion throttle pedal insecure. (6.2.4 (a) (ii)) | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front Wheel stud|s| missing |4.2.A.1e| | 1 |
| Offside Front Brake pipe leaking |3.6.A.1| | 1 |
| Nearside Front All position lamps not working |1.1.A.3b| | 1 |
| Nearside Rear All position lamps not working |1.1.A.3b| | 1 |
| Rear fog lamp switch faulty |1.3.1a| | 1 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Exhaust system not adequately supported |7.1.1| | 1 |
| Brake pedal spongy |3.3.B.1b| | 1 |
| Offside Front Bumper damaged and likely to cause injury when grazed or contacted end cap missing sharp edges protruding |6.1.4 |a| |i|| | 1 |
| Offside Rear Bumper damaged and likely to cause injury when grazed or contacted end cap missing jagged edge protruding |6.1.4 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Body component corroded and likely to cause injury floor (6.2.1 (a) (i)) | 1 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid |3.6.A.1| | 1 |
| Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jacking point (6.2.2 (d) (i)) | 1 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Front Body has a sharp edge caused by corrosion corrosion hole inner sill |6.1.C.1| | 1 |
| Nearside Front Body has a sharp edge caused by corrosion outer sill corrosion hole |6.1.C.1| | 1 |
| Offside Outer Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Mechanical brake component has restricted free movement | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front front brake binding |3.7.B.1| | 1 |
| An item not tested |Manual| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 1 |
| Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Nearside Front Upper Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Steering rack gaiter insecure |2.2.D.2d| | 1 |
| Rear Exhaust has a major leak of exhaust gases pipe missing |7.1.2| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded floorpan |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floorpan |5.2.6| | 1 |
| Front Anti-roll bar rubber bush deteriorated resulting in excessive movement d bushes both |2.4.G.2| | 1 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Front Anti-roll bar linkage severely distorted |2.4.G.1| | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front brake disc excessively scored |3.5.1h| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Direction indicator has less than 50% of the light sources illuminating |1.4.A.2c| | 1 |
| Offside Rear Direction indicator has less than 50% of the light sources illuminating |1.4.A.2c| | 1 |
| Horn control insecure |1.6.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill area |2.4.A.3| | 1 |
| Rear Exhaust has a major leak of exhaust gases elbow pipe |7.1.2| | 1 |
| Emissions not tested |7.4.B.1| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings step |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings step |6.1.B.2| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion wheel arch |6.1.C.1| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings excessive corrosion with in 30cm of nearside out riggar |6.1.B.2| | 1 |
| Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Front Lower Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Obligatory mirror insecure |8.1.1| | 1 |
| Brake fluid warning lamp illuminated |3.6.G.2| | 1 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Hazard warning lamps operated by more than one switch |1.4.B.1c| | 1 |
| Brake hose damaged | 1 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Emissions not tested |7.0| | 1 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Stop lamp not working |1.2.1b| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Horn not working |7.7 |a| |ii|| | 1 |
| Nearside Front Upper Anti-roll bar locating pin incorrectly positioned |2.4.G.3a| | 1 |
| Offside Rear wheel cylinder leaking |3.6.A.1| | 1 |
| Nearside Front Brake hose leaking |3.6.A.1| | 1 |
| Front Windscreen wiper not working (3.4 (a)) | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill and floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength bottom off inner arch (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
| Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill detached (6.1.1 (c) (i)) | 1 |
| All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
| Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Steering rack gaiter insecure |2.2.D.2d| | 1 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 1 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Front Steering arm has relative movement at its fixings |2.2.B.1h| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Front Position lamp adversely affected by the operation of another lamp (both) (4.2.3 (c)) | 1 |
| Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| All direction indicators adversely affected by the operation of another lamp (4.4.3 (b)) | 1 |
| Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Upper Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Rear Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Rear Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Rear Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Nearside Rear Suspension arm insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Suspension arm attachment bracket/mounting likely to become detached (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Suspension arm attachment bracket/mounting insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure has a fracture which is likely to adversely affect braking or steering (6.1.1 (a) (ii)) | 1 |
| Offside Headlamp insecure (4.1.1 (c)) | 1 |
| Brake performance unable to be tested (1.2.1 (g)) | 1 |
| Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Nearside Rear Suspension arm insecurely attached (5.3.3 (a) (i)) | 1 |
| Nearside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn d bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn top bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn top bush (5.3.4 (a) (i)) | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Seat belt buckle not functioning as intended at the seat (7.1.2 (d)) | 1 |
| Nearside Front Front suspension has excessive play in a pin or bush of an upper wishbone inner bearing |2.5.B.1a| | 1 |
| Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Trailing arm rubber bush deteriorated resulting in excessive movement front bush split |2.4.G.2| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded sill area near spring hanger |2.4.A.3| | 1 |
| Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch (6.2.2 (d) (i)) | 1 |
| Emissions not tested smoking heavy (8.2.2.2 (e)) | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded upper sill to B pillar |5.2.6| | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Lower Body has a sharp edge caused by corrosion sliding door badly corroded |6.1.C.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Nearside Front Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill corroded |6.1.B.2| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill corroded |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill to wheel arch corroded |6.1.B.2| | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill corroded |6.1.B.2| | 1 |
| Nearside Rear Suspension arm corroded and seriously weakened marked with yellow chalk |2.4.G.1| | 1 |
| Offside Rear Suspension arm corroded and seriously weakened marked with yellow chalk |2.4.G.1| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill to wheel arch |6.1.B.2| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected arch (5.3.6 (a) (ii)) | 1 |
| Exhaust emits excessive smoke or vapour likely to obscure the vision of other road users (8.2.2.2 (c)) | 1 |
| Offside Front Inner Integral body structure has excessive corrosion which adversely affects braking or steering arch (6.1.1 (c) (ii)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch front (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch rear (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch front (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch rear (5.3.6 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced step (6.1.1 (c) (i)) | 1 |
| Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Brake pedal anti-slip provision missing brake |3.3.A.1b| | 1 |
| Speedometer cannot be illuminated. |6.7.3| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Obligatory mirror insecure |8.1.1| | 1 |
| Position lamp not working o/s/f sidelight (4.2.1 (a) (ii)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced n/s/r inner wheel arh seat belt mount area corroded (7.1.1 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced o/s/r inner wheel arch seat belt mount area corroded (7.1.1 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s/r cross member /susp mount area corroded (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength n/s/r crossmember /susp mount area corroded (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength n/s/r inner sill/susp mount area corroded (5.3.6 (a) (i)) | 1 |
| Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced o/s/f inner sill/outrigger/inner wheelarch area corroded (6.1.1 (c) (i)) | 1 |
| Hazard warning lamps inoperative all hazards not working |1.4.B.1b| | 1 |
| Suspension component mounting prescribed area is excessively corroded o/s/r inner sill |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded o/s/r | lower front arm mount area| |2.4.A.3| | 1 |
| Seat belt anchorage prescribed area is excessively corroded n/s/f s/belt mount area |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded o/s/f s/belt mount area |5.2.6| | 1 |
| Anti-roll bar attachment bracket/mounting insecure n/s/f lower droplink bush insecure |2.4.G.1| | 1 |
| Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt n/s/f top ball joint cover split |2.4.G.2| | 1 |
| Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt o/s/f top ball joint cover split |2.4.G.2| | 1 |
| Brake pedal anti-slip provision loose insecure |worn | |3.3.A.1b| | 1 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| All position lamps not working |1.1.A.3b| | 1 |
| Headlamp not working on dipped beam |1.7.5a| | 1 |
| Headlamp not working on main beam |1.7.5a| | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Direction indicators not working |1.4.A.2c| | 1 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 1 |
| Nearside Rear coil spring incomplete |2.4.C.1a| | 1 |
| Offside Rear coil spring incomplete |2.4.C.1a| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced step / arch area (7.1.1 (a) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg (6.1.1 (c) (i)) | 1 |
| Brake pedal anti-slip provision missing (1.1.2 (c)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill / inner arch / step / jacking point (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch / rear quarter (6.1.1 (c) (i)) | 1 |