| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 17 |
| Registration plate lamp issues | 14 |
| Windscreen wiper does not clear the windscreen effectively | 13 |
| Headlamp aim out of alignment | 13 |
| Brake hose excessively deteriorated | 11 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 9 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 8 |
| Offside Rear fog lamp not working |1.3.2b| | 6 |
| Registration plate issues | 4 |
| Horn not working |1.6.2a| | 4 |
| Rear fog lamp tell tale not working |1.3.1b| | 4 |
| Parking brake: efficiency below requirements |3.7.B.7| | 3 |
| Rear brake application uneven | 3 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 3 |
| Brakes imbalanced across an axle | 3 |
| Rear fog lamp not working |1.3.2b| | 3 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Fuel system component leaking |7.2.3| | 2 |
| Emissions not tested |7.0| | 2 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Nearside Front front brake binding |3.7.B.1| | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Rear coil spring broken |2.4.C.1a| | 2 |
| Service brake: efficiency below requirements |3.7.B.7| | 2 |
| Windscreen washer not working | 2 |
| Nearside Stop lamp not working |1.2.1b| | 2 |
| Offside Steering rack gaiter split |2.2.D.2d| | 2 |
| Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 2 |
| Offside Front Headlamp aim beam image kick up to the offside |1.8| | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Stop lamp not working |1.2.1b| | 2 |
| Nearside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
| Exhaust system not adequately supported |7.1.1| | 2 |
| Front brake application uneven | 2 |
| Rear Rear fog lamp missing |1.3.2a| | 2 |
| Offside Rear wheel bearing has excessive play |2.6.2| | 2 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 2 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 2 |
| Horn not working (7.7 (a)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Front Power steering pipe/hose leaking (2.1.5 (a)) | 2 |
| Nearside Front Lower Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Offside Front Lower Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Nearside Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Rear Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
| Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded chalked area |2.4.A.3| | 1 |
| Fuel cap/sealing device sealing washer missing |7.2.4c| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Braking system leaking |3.6.A.1| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Position lamp not working |4.2.1 |a|| | 1 |
| Offside Front Anti-roll bar linkage insecurely attached |5.3.3 |a| |i|| | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Nearside Front Upper Suspension arm pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch |6.1.B.2| | 1 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 1 |
| Nearside Rear Lower Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 1 |
| Offside Steering rack gaiter insecure |2.2.D.2d| | 1 |
| Nearside Front Upper Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Offside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Rear coil spring incomplete |2.4.C.1a| | 1 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Rear fog lamp obviously incorrectly positioned should be on the O/S/R |4.5.4 |a|| | 1 |
| Nearside Front Anti-roll bar pin or bush excessively worn D bush |5.3.4 |a| |i|| | 1 |
| Exhaust emissions exceed manufacturer`s specified limit |8.2.2.2 |a|| | 1 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Rear Rear fog lamp obviously incorrectly positioned |1.3.2a| | 1 |
| Nearside Direction indicator not working |1.4.A.2c| | 1 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front Upper Suspension arm synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Rear fog lamp switch insecure |1.3.1a| | 1 |
| Nearside Rear fog lamp not working |1.3.2b| | 1 |
| Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
| Brake performance not tested |1.2.1 |g|| | 1 |
| Offside Rear Brake pipe leaking on a hydraulic braking system pipe to hose |1.1.11 |b| |ii|| | 1 |
| Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Nearside Front Brake hose bulging under pressure |3.6.B.3| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| rear brakes release unevenly |3.7.B.4| | 1 |
| Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Rear position lamp|s| not working BOTH |1.1.A.3b| | 1 |
| Offside Rear Body insecure and dangerous to other road users BUMPER END |6.1.B.1b| | 1 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Offside Rear Brake pipe leaking |3.6.A.1| | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Suspension component mounting prescribed area is excessively corroded Centre chassis |2.4.A.3| | 1 |
| Centre Brake pipe inadequately supported |3.6.B.1| | 1 |
| Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded sill/sill end |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Fuel tank leaking |7.2.3| | 1 |
| Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 1 |
| Offside Front Steering rack gaiter insecure |2.2.D.2d| | 1 |
| Nearside Rear Drive shaft uj which forms part of the suspension has an inadequately locked flange bolt |2.4.G.4c| | 1 |
| Rear brake binding | 1 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Fuel system component leaking excessively or a risk of fire |6.1.3 |b| |ii|| | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Rear Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Centre Rear Statutory seat belt missing |5.1.1| | 1 |
| Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 1 |
| Nearside Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
| Nearside Front Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
| Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Front Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Centre Front Obligatory mirror missing |8.1.1| | 1 |
| Offside Front front brake binding |3.7.B.1| | 1 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Rear Exhaust system not adequately supported hanger broken |7.1.1| | 1 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Rear fog lamp has less than 50% of the light sources illuminating |1.3.2b| | 1 |
| Rear fog lamp switch missing |1.3.1a| | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced step (6.1.1 (c) (i)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Nearside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Body panel corroded and likely to cause injury sill (6.2.1 (a) (i)) | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Main beam tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Front Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Anti-roll bar pin or bush excessively worn body bush(D-bush) (5.3.4 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases back box (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Brake pipe leaking on a hydraulic braking system front to rear (1.1.11 (b) (ii)) | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced CHASSIS (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced WHEEL ARCH (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced WHEEL ARCH (6.1.1 (c) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER SILL (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER SILL (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER SILL (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER WHEEL ARCH (6.1.1 (c) (i)) | 1 |
| Offside Front Upper Suspension arm pin or bush excessively worn Front bush (5.3.4 (a) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced INNER ARCH (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced OUTER SILL (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced UPPER CHASSIS LEG (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid (1.1.16 (b) (i)) | 1 |
| Nearside Rear Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Fuel system component leaking (6.1.3 (b) (i)) | 1 |