Most common failures | No# failures |
---|
Brake pipe excessively corroded | 82 |
Parking brake: efficiency below requirements |3.7.B.7| | 50 |
Windscreen wiper does not clear the windscreen effectively | 48 |
Registration plate lamp issues | 48 |
Headlamp aim out of alignment | 43 |
Brake hose excessively deteriorated | 38 |
Brakes imbalanced across an axle | 27 |
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 25 |
Horn not working |1.6.2a| | 24 |
Rear parking brake recording little or no effort | 22 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 18 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 16 |
Offside Rear fog lamp not working |1.3.2b| | 16 |
Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 13 |
Registration plate issues | 13 |
Exhaust has a major leak of exhaust gases |7.1.2| | 12 |
Service brake: efficiency below requirements |3.7.B.7| | 11 |
Nearside front brake binding |3.7.B.1| | 11 |
Rear brake binding | 10 |
Offside front brake binding |3.7.B.1| | 9 |
Nearside Steering rack gaiter split |2.2.D.2d| | 9 |
Rear fog lamp not working |1.3.2b| | 9 |
Offside Stop lamp not working |1.2.1b| | 8 |
Offside Steering rack gaiter split |2.2.D.2d| | 8 |
Nearside Stop lamp not working |1.2.1b| | 7 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
Rear brake application uneven | 7 |
Brake hose has insufficient room to move | 6 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 6 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
Parking brake lever has no reserve travel |3.1.6b| | 6 |
Parking brake efficiency below requirements |1.4.2 |a| |i|| | 5 |
Offside Front Steering rack gaiter split |2.2.D.2d| | 5 |
Windscreen washer not working | 5 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 5 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
Front brake application uneven | 5 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 5 |
Exhaust emissions carbon monoxide content excessive |8.2.1.2 |b|| | 5 |
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 5 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 5 |
Offside Rear Stop lamp not working |1.2.1b| | 4 |
Hazard warning tell tale not working correctly |1.4.B.1e| | 4 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
Indicator tell tale inoperative |1.4.A.2a| | 4 |
Rear fog lamp tell tale not working |1.3.1b| | 4 |
Nearside Rear Stop lamp not working |1.2.1b| | 4 |
Windscreen has damage | 4 |
Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 4 |
Offside Front front brake binding |3.7.B.1| | 4 |
Fuel pipe leaking |7.2.3| | 4 |
Nearside Rear wheel bearing has excessive play |2.6.2| | 4 |
Offside Rear wheel bearing has excessive play |2.6.2| | 4 |
Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 4 |
Nearside Front Body has a sharp edge caused by damage |6.1.C.1| | 4 |
Nearside Headlamp not working on main beam |1.7.5a| | 4 |
Offside Headlamp not working on main beam |1.7.5a| | 4 |
Offside Front Upper Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 4 |
Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 4 |
Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 4 |
Nearside Rear Brake hose bulging under pressure |3.6.B.3| | 4 |
Nearside Front Brake hose bulging under pressure |3.6.B.3| | 4 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 4 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 4 |
Horn not working |7.7 |a| |ii|| | 3 |
Offside Front Anti-roll bar linkage insecure |2.4.G.1| | 3 |
All position lamps not working |1.1.A.3b| | 3 |
Hazard warning switch faulty |1.4.B.1d| | 3 |
Nearside Front coil spring fractured |2.4.C.1a| | 3 |
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Front Service brake excessively binding |1.2.1 |f|| | 3 |
Offside Rear Brake back plate|s| securing device excessively deteriorated |3.5.1j| | 3 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
Offside Rear coil spring fractured |2.4.C.1a| | 3 |
Stop lamp|s| all not working |4.3.1 |a| |iii|| | 3 |
Offside Headlamp aim beam image kick up to the offside |1.8| | 3 |
Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
Nearside Front Steering rack gaiter split |2.2.D.2d| | 3 |
Nearside Front Anti-roll bar linkage fractured |2.4.G.1| | 3 |
Exhaust engine idle speed too high |7.3.A.2a| | 3 |
Offside Rear Rear wheel bearing has excessive play |2.6.2| | 3 |
Nearside Rear Direction indicator not working |1.4.A.2c| | 3 |
Battery insecure |1.9.1| | 3 |
Offside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 3 |
Offside Rear coil spring incomplete |2.4.C.1a| | 3 |
Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Offside Headlamp not working on dipped beam |1.7.5a| | 3 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
Steering rack insecure |2.2.B.1a| | 3 |
Exhaust emissions hydrocarbon content excessive |8.2.1.2 |b|| | 3 |
Offside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Rear Brake hose bulging under pressure |3.6.B.3| | 3 |
Offside Rear coil spring broken |2.4.C.1a| | 3 |
Rear Stop lamp not working |1.2.1b| | 3 |
Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 3 |
Brake performance not tested |3.7.A.1| | 3 |
Nearside Front Upper Suspension arm has excessive play in a pin/bush |2.4.G.2| | 3 |
Brake hose damaged | 3 |
Offside Front Brake pipe inadequately clipped |3.6.B.1| | 2 |
Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
Nearside Windscreen wiper not operating automatically when switched on |8.2.1b| | 2 |
Offside Front Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 2 |
Offside Front coil spring fractured |2.4.C.1a| | 2 |
Fuel hose excessively damaged |7.2.2| | 2 |
Offside Rear Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 2 |
Fuel system component insecure |7.2.1| | 2 |
Nearside Headlamp aim beam image kick up to the offside |1.8| | 2 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Hazard warning switch insecure |1.4.B.1d| | 2 |
Direction indicators flashing more than 120 times a minute |1.4.A.2g| | 2 |
Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 2 |
Nearside Front front brake binding |3.7.B.1| | 2 |
Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 2 |
Offside Rear fog lamp missing |1.3.2a| | 2 |
Offside Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 2 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
Offside Front Upper Suspension arm has excessive play in a pin/bush |2.4.G.2| | 2 |
Offside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 2 |
Offside rear brake recording little or no effort |3.7.B.5a| | 2 |
Exhaust has a part missing |7.1.1a| | 2 |
Speedometer cannot be illuminated. |6.7.3| | 2 |
Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 2 |
Offside Front coil spring broken |2.4.C.1a| | 2 |
Nearside Front brake disc excessively pitted |3.5.1h| | 2 |
Offside Front brake disc excessively pitted |3.5.1h| | 2 |
Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Front brake disc in such a condition that it is seriously weakened | 2 |
Nearside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Offside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Offside Obligatory mirror seriously deteriorated, affecting the rear view |8.1.2a| | 2 |
Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Driver`s seat insecure |6.2.A.1| | 2 |
Offside Front coil spring cracked |2.4.C.1a| | 2 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
Offside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Fuel cap/sealing device sealing washer deteriorated |7.2.4c| | 2 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Offside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 2 |
Rear Fuel pipe leaking |7.2.3| | 2 |
Nearside Rear fog lamp not working |1.3.2b| | 2 |
Offside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
Offside Inner Rear Drive shaft which forms part of the suspension coupling gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.4.G.4e| | 2 |
Nearside Front Service brake excessively binding |1.2.1 |f|| | 2 |
Nearside rear brake excessively fluctuating |3.7.B.3| | 2 |
Offside rear brake excessively fluctuating |3.7.B.3| | 2 |
Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Nearside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 2 |
Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 2 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 2 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 2 |
Horn not working (7.7 (a)) | 2 |