Most common failures | No# failures |
---|
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 13 |
Brake hose excessively deteriorated | 12 |
Parking brake: efficiency below requirements |3.7.B.7| | 12 |
Headlamp aim out of alignment | 11 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
Brake pipe excessively corroded | 10 |
Registration plate lamp issues | 10 |
Windscreen wiper does not clear the windscreen effectively | 8 |
Horn not working |1.6.2a| | 7 |
Rear parking brake recording little or no effort | 5 |
Service brake: efficiency below requirements |3.7.B.7| | 5 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Offside Front position lamp|s| not working |1.1.A.3b| | 4 |
Nearside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 3 |
Offside Rear fog lamp not working |1.3.2b| | 3 |
Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 3 |
Offside Headlamp not working on dipped beam |1.7.5a| | 3 |
Brakes imbalanced across an axle | 3 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 3 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 3 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Parking brake: efficiency below requirements |3.7.C.1b| | 2 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 2 |
Nearside Rear coil spring incomplete |2.4.C.1a| | 2 |
Offside Front front brake binding |3.7.B.1| | 2 |
Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
Offside Front Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
Offside Front Coil spring fractured or broken |5.3.1 |b| |i|| | 2 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 2 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 2 |
Offside Front Body has a sharp edge caused by damage |6.1.C.1| | 2 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Stop lamp not working |1.2.1b| | 2 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside Stop lamp not working |1.2.1b| | 2 |
Offside Rear Suspension arm corroded and seriously weakened |2.4.G.1| | 2 |
Rear brake binding | 2 |
Nearside Rear Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
Horn not working (1.6.2a) | 2 |
Offside Rear Suspension arm corroded and seriously weakened (2.4.G.1) | 2 |
Horn not working (7.7 (a) (ii)) | 2 |
Offside Rear Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
Offside Rear Suspension arm attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 2 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Coil spring mounting corroded and seriously weakened |2.4.C.3c| | 1 |
Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Tie bar/rod attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
Nearside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
Nearside Rear Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 1 |
Offside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Service brake: efficiency below requirements |3.7.C.1a| | 1 |
Offside Front coil spring incomplete |2.4.C.1a| | 1 |
Offside Outer Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
Nearside Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
Nearside Outer Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Direction indicator not working |4.4.1 |a| |ii|| | 1 |
Nearside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area for rear axle. |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area for rear axle. |5.3.6 |a| |i|| | 1 |
Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced crossmember. |6.1.1 |c| |i|| | 1 |
Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced crossmember. |6.1.1 |c| |i|| | 1 |
Offside Front Inner Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner and outer sill |6.1.B.2| | 1 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner and outer sill |6.1.B.2| | 1 |
Headlamp switch faulty |1.7.1| | 1 |
Nearside Rear Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Hazard warning switch faulty |1.4.B.1d| | 1 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Front Anti-roll bar insecure |2.4.G.1| | 1 |
Nearside Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Front Upper Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Fuel pipe leaking |7.2.3| | 1 |
Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Inner Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
Offside Inner Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.4.B.1| | 1 |
Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Brake hose damaged | 1 |
Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Headlamp insecure |1.7.3| | 1 |
Offside Headlamp insecure |1.7.3| | 1 |
Offside Headlamp not working on main beam |1.7.5a| | 1 |
Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
Offside Rear Direction indicator incorrect colour lense broken |1.4.A.2f| | 1 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 1 |
Brake valve leaking |3.6.A.1| | 1 |
Nearside Front Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
Nearside Drag link end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt front and rear |2.2.C.1c| | 1 |
Nearside Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
Offside Statutory seat belt missing stalk missing |5.1.1| | 1 |
Front Electrical wiring inadequately supported |1.9.2a| | 1 |
Brake pipe inadequately supported front to rear |3.6.B.1| | 1 |
Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 1 |
Battery insecure |1.9.1| | 1 |
Nearside Rear Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
Offside Rear Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
Brake pipe leaking on a hydraulic braking system brake pipe over rear transaxle |1.1.11 |b| |ii|| | 1 |
Nearside Front Coil spring fractured or broken |5.3.1 |b| |i|| | 1 |
Offside Front Upper Suspension component pin or bush excessively worn inner wishbone bush |5.3.4 |a| |i|| | 1 |
Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
Exhaust system insecure |6.1.2 |a|| | 1 |
Headlamp aim beam image kick up to the offside both |1.8| | 1 |
Offside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 1 |
Rear brake application uneven | 1 |
Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 1 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Lower Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Fuel cap/sealing device sealing washer deteriorated |7.2.4c| | 1 |
Nearside Front coil spring fractured |2.4.C.1a| | 1 |
Offside Rear Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded OUTER SILL |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded OUTER SILL |2.4.A.3| | 1 |
Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
Nearside Direction indicator not working |1.4.A.2c| | 1 |
Headlamp switch insecure |1.7.1| | 1 |
Hazard warning switch insecure |1.4.B.1d| | 1 |
Offside Front Upper Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Upper Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Stop lamp not working |1.2.1b| | 1 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
Offside Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
Nearside Front Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Nearside Rear Stop lamp not working |1.2.1b| | 1 |
Offside Rear Stop lamp not working |1.2.1b| | 1 |
Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Steering column top bearing excessively worn |2.1.2c| | 1 |
Registration plate issues | 1 |
Offside Front Direction indicators not working |1.4.A.2c| | 1 |
Offside Rear Brake pipe leaking |3.6.A.1| | 1 |
Brake pedal creeps down when held under pressure |3.3.B.1a| | 1 |
Front brake application uneven | 1 |
Nearside Rear Position lamp not working |4.2.1 |a|| | 1 |
Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 1 |
Nearside Front coil spring broken |2.4.C.1a| | 1 |
Offside Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
Offside Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
Offside Rear coil spring fractured |2.4.C.1a| | 1 |
Nearside Front Track rod end loose |2.2.B.1d| | 1 |
Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Lower Suspension rod ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Offside Lower Suspension rod ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Nearside Suspension rod likely to fail |5.3.3 |b| |ii|| | 1 |
Offside Suspension rod likely to fail |5.3.3 |b| |ii|| | 1 |
Rear Oil leaking excessively from engine |8.4.1 |a| |i|| | 1 |
Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
Offside Front Upper Suspension arm insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
Offside Front Upper Suspension arm has excessive play in a pin/bush (2.4.G.2) | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch (2.4.A.3) | 1 |
Offside Rear Radius arm corroded and seriously weakened (2.4.G.1) | 1 |
Offside Rear Lower Coil spring mounting corroded and seriously weakened (2.4.C.3c) | 1 |
Nearside Rear Direction indicator not working (1.4.A.2c) | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3) | 1 |
Nearside Rear Suspension arm corroded and seriously weakened (2.4.G.1) | 1 |
Nearside Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
Nearside Rear Upper Suspension spring mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Nearside Rear Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
Hazard warning tell tale not working correctly (1.4.B.1e) | 1 |
Offside Rear fog lamp not working (1.3.2b) | 1 |
Offside Steering rack gaiter split (2.2.D.2d) | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Rear Exhaust system not adequately supported (7.1.1) | 1 |
Nearside Headlamp not in good working order adversely affecting beam image (1.2.4a) | 1 |
Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
Offside Body component corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
Nearside Rear Suspension arm attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Emissions not tested (8.2.2.2 (e)) | 1 |
Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced JACKING POINT (6.1.1 (c) (i)) | 1 |
Fuel hose damaged filler neck (6.1.3 (c) (ii)) | 1 |
Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
Offside Rear Brake drum back plate insecure (1.1.14 (d)) | 1 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis/inner sill (6.1.1 (c) (i)) | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis/inner sill (6.1.1 (c) (i)) | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
Nearside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting (6.2.2 (d) (i)) | 1 |
Offside Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting unsuitable repair on the lower sill (6.2.2 (d) (i)) | 1 |
Nearside Rear Brake drum back plate insecure (1.1.14 (d)) | 1 |
Nearside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Nearside Rear Shock absorbers has an excessively worn bush Lower bush (5.3.2 (c)) | 1 |
Nearside Front Brake hose bulging under pressure (1.1.12 (d)) | 1 |
Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front too rear inner and outer sills (6.1.1 (c) (i)) | 1 |
Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front too rear inner and outer sills (6.1.1 (c) (i)) | 1 |
Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis/inner sill (6.1.1 (c) (i)) | 1 |
Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis/inner sill (6.1.1 (c) (i)) | 1 |
Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced engine area chassis (6.1.1 (c) (i)) | 1 |
Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced engine are chassis (6.1.1 (c) (i)) | 1 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Offside Rear Outer Bumper damaged and likely to cause injury when grazed or contacted end cap missing (6.1.4 (a) (i)) | 1 |
Nearside Front Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |