| Most common failures | No# failures |
|---|
| Parking brake: efficiency below requirements |3.7.B.7| | 13 |
| Headlamp aim out of alignment | 12 |
| Registration plate issues | 10 |
| Registration plate lamp issues | 7 |
| Rear parking brake recording little or no effort | 6 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 5 |
| Horn not working |1.6.2a| | 5 |
| Offside Stop lamp not working |1.2.1b| | 5 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 4 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 4 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Brakes imbalanced across an axle | 3 |
| Windscreen washer not working | 3 |
| Steering system has excessive free play detected at the steering wheel |steering box fitted| |2.2.A.1a| | 3 |
| Windscreen wiper does not clear the windscreen effectively | 3 |
| Offside Rear Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 3 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 3 |
| Brake hose excessively deteriorated | 3 |
| Horn not working (7.7 (a) (ii)) | 2 |
| Offside Front Headlamp aim beam image obviously incorrect (1.8.A.1b) | 2 |
| Nearside Front Headlamp aim beam image obviously incorrect (1.8.A.1b) | 2 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 2 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 2 |
| Rear Drag link end ball joint has excessive play |2.2.B.1f| | 2 |
| Centre Front Statutory seat belt missing |5.1.1| | 2 |
| Centre Steering pivot point has excessive play |2.2.B.1g| | 2 |
| Offside Rear position lamp|s| incorrect colour |1.1.A.3e| | 2 |
| Offside Rear Brake pipe inadequately supported |3.6.B.1| | 2 |
| Nearside Rear Direction indicators adversely affected by the operation of another lamp |1.4.A.2h| | 2 |
| Stop lamp not working |1.2.1b| | 2 |
| Exhaust emissions hydrocarbon content excessive |8.2.1.2 |b|| | 2 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 2 |
| Headlamp switch faulty (1.7.1) | 1 |
| Steering box has relative movement between sector shaft and the drop arm (2.2.B.1b) | 1 |
| Steering box insecure (2.2.B.1a) | 1 |
| Nearside Rear Rear wheel bearing rough when rotated (2.6.1) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting nut missing (2.4.G.1) | 1 |
| Offside Track rod end loose (2.2.B.1d) | 1 |
| Nearside Front wheel bearing has excessive play (2.5.A.3c) | 1 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 1 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
| Drivers door cannot be opened from outside the vehicle (6.2.B.1b) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Nearside Rear Vehicle structure has a fracture which adversely affects braking or steering (6.1.A.1) | 1 |
| Nearside Front Anti-roll bar linkage fractured (2.4.G.1) | 1 |
| Offside Front Anti-roll bar linkage fractured (2.4.G.1) | 1 |
| Offside Side repeater not working |1.4.A.2c| | 1 |
| Front Steering pivot point has excessive play |2.2.B.1g| | 1 |
| Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Service brake is causing the steering wheel to severely pull one way |3.7.C.2| | 1 |
| Brake pedal anti-slip provision worn smooth |3.3.A.1b| | 1 |
| Steering column top bearing excessively worn |2.1.2c| | 1 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 1 |
| Offside Outer Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Inner Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Front Anti-roll bar fractured |2.4.G.1| | 1 |
| Nearside Rear Shock absorbers has a serious fluid leak | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chasis rail (6.1.1 (c) (i)) | 1 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Position lamp switch faulty |1.1.A.1| | 1 |
| Brake pedal spongy |3.3.B.1b| | 1 |
| Nearside Front Direction indicator missing |1.4.A.2b| | 1 |
| Offside Front Direction indicator missing |1.4.A.2b| | 1 |
| Front Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
| Front Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
| Rear Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
| Nearside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Fuel system component insecure |7.2.1| | 1 |
| Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Rear Stop lamp not working |1.2.1b| | 1 |
| Front brake application uneven | 1 |
| Offside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Rear Brake pipe inadequately supported |3.6.B.1| | 1 |
| Oil leaking excessively from engine |8.4.1 |a| |i|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Central Front Inner Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt both |2.1.3 |g| |ii|| | 1 |
| Nearside Front Outer Track rod end seriously misaligned |2.1.3 |e|| | 1 |
| Offside Front Direction indicators not working |1.4.A.2c| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Offside Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Front Body has a projection caused by corrosion door |6.1.C.1| | 1 |
| Offside Front Body has a projection caused by corrosion door |6.1.C.1| | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Nearside Front Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Stop lamp remains on when the brakes are released | 1 |
| Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded front to rear |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded front to rear |2.4.A.3| | 1 |
| Offside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch and crossmember |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cross member |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner step and wheel arch |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wheel arch near seatbelt mount |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings floor |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under sill |6.1.B.2| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under sill |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis and floor |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings crossmember |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cross member and floor panel |6.1.B.2| | 1 |
| Offside Rear Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Offside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Rear Outer Drive shaft which forms part of the suspension coupling gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.4.G.4e| | 1 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Body has a sharp edge caused by corrosion step |6.1.C.1| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded sill to outer sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
| Nearside Front brake caliper securing device missing |3.5.1j| | 1 |
| Offside Front brake caliper securing device loose |3.5.1j| | 1 |
| Offside Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Nearside Stop lamp not working |1.2.1b| | 1 |
| Nearside Headlamp not working on main beam |1.7.5a| | 1 |
| Windscreen wiper blade insecure | 1 |
| Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Rear brake binding | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings arch |6.1.B.2| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings step |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings step |6.1.B.2| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Horn not working (7.7 (a)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Rear Position lamp not working |4.2.1 |a|| | 1 |
| Nearside Front Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Offside Front Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Exhaust emissions carbon monoxide content excessive |8.2.1.2 |b|| | 1 |
| Offside Rear Towbar is so weakened by corrosion within 30cm of a towbar mounting, the towbar is likely to become detached most panel |6.1.6 |i| |ii|| | 1 |
| All position lamps adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Offside Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Steering column flexible coupling is excessively deteriorated |2.1.5| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Front Headlamp does not operate immediately when selected on dipped beam |1.7.4a| | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Upper Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Lower Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Front Steering component mounting prescribed area has a deliberate modification which significantly reduces the original strength |2.2.C.1h| | 1 |
| Nearside Front Brake actuating linkage mounting prescribed area is excessively corroded |3.3.A.2| | 1 |
| Rear Stop lamp not working |1.2.1b| | 1 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 1 |
| Horn is a siren |1.6.2c| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Hazard warning switch insecure |1.4.B.1d| | 1 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Central Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Steering system has excessive free play detected at the steering wheel |steering box fitted| idler |2.2.A.1a| | 1 |
| Offside Front Shock absorber casing corroded externally so the unit does not function |2.7.2a| | 1 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Rear Access panel cannot be secured in the closed position |6.2.1 |e|| | 1 |
| Horn not working |7.7 |a| |ii|| | 1 |
| Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Emissions not tested |7.0| | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |
| Horn not loud enough to be heard by another road user |1.6.2b| | 1 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Offside Rear Drive shaft which forms part of the suspension coupling gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.4.G.4e| | 1 |
| Nearside Front Sub-frame corroded and seriously weakened front axle |2.4.G.1| | 1 |
| Offside Front Lower Front suspension ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Nearside Front Direction indicator not working |4.4.1 |a| |ii|| | 1 |
| Central Front Direction indicator not working |4.4.1 |a| |ii|| | 1 |
| Offside Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
| Nearside Rear Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment |1.1.6 |c|| | 1 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Drive shaft which forms part of the suspension coupling gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.4.G.4e| | 1 |
| Nearside Rear Drive shaft which forms part of the suspension coupling gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.4.G.4e| | 1 |
| Vehicle Identification Number not permanently displayed |6.3.5.a| | 1 |