| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 26 |
| Headlamp aim out of alignment | 25 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 12 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 12 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 11 |
| Brakes imbalanced across an axle | 9 |
| Rear fog lamp not working |1.3.2b| | 9 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 9 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 8 |
| Registration plate lamp issues | 8 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 8 |
| Parking brake: efficiency below requirements |3.7.B.7| | 6 |
| Offside Rear fog lamp not working |1.3.2b| | 6 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 6 |
| Windscreen washer not working | 5 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 5 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 5 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 4 |
| Emissions not tested |7.0| | 4 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 4 |
| Horn not working |1.6.2a| | 3 |
| Horn not working (7.7 (a)) | 3 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Hazard warning switch faulty |1.4.B.1d| | 3 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 3 |
| Brake hose has insufficient room to move | 3 |
| Registration plate issues | 3 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 3 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 3 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 2 |
| Offside Front Axle swivel pins and bushes swivel pin and/or bush excessively worn (5.1.2 (b) (i)) | 2 |
| Hazard warning lamps inoperative (4.4.1 (e)) | 2 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 2 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Passengers seat insecure (6.2.6 (a) (ii)) | 2 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Brake hose damaged | 2 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 2 |
| Rear brake binding | 2 |
| Rear fog lamp insecure |1.3.2a| | 2 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Brake pedal spongy |3.3.B.1b| | 2 |
| Nearside Stop lamp not working |1.2.1b| | 2 |
| Steering system has excessive free play detected at the steering wheel |steering box fitted| |2.2.A.1a| | 2 |
| Steering box insecure |2.2.B.1a| | 2 |
| Offside Rear Rear fog lamp missing |1.3.2a| | 2 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 2 |
| Nearside Rear Battery insecure |1.9.1| | 2 |
| Offside Rear Battery insecure |1.9.1| | 2 |
| Nearside Front Seat belt installation has cut and/or reworked original webbing (10.1 (a)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Headlamp not working on main beam LHD,, passenger side (4.1.1 (a) (ii)) | 1 |
| Steering locking device ineffective steering damper nut/bolt loose (2.1.3 (d)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Rear Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Offside Front Suspension component pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Windscreen wiper not working (3.4 (a)) | 1 |
| Rear Exhaust has a major leak of exhaust gases rear box both sides (6.1.2 (a)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Lower Axle swivel pins and bushes swivel pin and/or bush excessively worn (5.1.2 (b) (i)) | 1 |
| Nearside Front Upper Axle swivel pins and bushes swivel pin and/or bush excessively worn (5.1.2 (b) (i)) | 1 |
| Offside Front Seat belt not functioning as intended (7.1.2 (c)) | 1 |
| Service brake: efficiency below requirements |3.7.C.1a| | 1 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 1 |
| Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Rear Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Steering box has excessive free play detected at the steering wheel (steering box fitted) play centre steering idler arm pin/bush (2.3 (a) (i)) | 1 |
| Nearside Steering component mounting prescribed area is excessively corroded front box section with in 20cm of steering box mounting (2.1.2 (e) (i)) | 1 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect kick up to o/s not n/s (4.1.2 (c)) | 1 |
| Drag link end ball joint worn to the extent there is a serious risk of detachment (2.1.3 (b) (ii)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill front to back (5.3.6 (a) (i)) | 1 |
| Central Rear Exhaust has a major leak of exhaust gases center box holed (6.1.2 (a)) | 1 |
| Service brake lagging in operation brake pedal travels to the floor (1.2.1 (d)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced step (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill/step (6.1.1 (c) (i)) | 1 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Nearside Headlamp aim not tested (4.1.2 (b)) | 1 |
| Nearside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Drivers seat backrest cannot be secured in the upright position. (6.2.5 (b) (ii)) | 1 |
| Nearside Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Offside Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Offside Front Upper Shock absorbers insecurely attached (5.3.2 (a) (i)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Front Service brake imbalanced across an axle (1.2.1 (b) (i)) | 1 |
| Nearside Front Upper Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Brake hose excessively deteriorated | 1 |
| Centre Stop lamp not working |1.2.1b| | 1 |
| Anti-lock braking system warning lamp indicates an ABS fault | 1 |
| Front Headlamp has a product on the light source so that the light output is severely reduced n/s and o/s (4.1.4 (b)) | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.B.1| | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 1 |
| Front Axle beam has excessive vertical movement between stub axle and axle beam |2.5.A.1a| | 1 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Nearside Integral body structure inadequately repaired such that structural rigidity is significantly reduced outer sill (6.1.1 (d) (i)) | 1 |
| Offside Integral body structure inadequately repaired such that structural rigidity is significantly reduced outer sill (6.1.1 (d) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Inner Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Offside Rear Exhaust has a major leak of exhaust gases silencer |7.1.2| | 1 |
| Horn not working |7.7 |a| |ii|| | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
| Nearside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Brake master cylinder leaking (1.1.10 (b) (ii)) | 1 |
| Offside Rear Axle has excessive vertical movement between stub axle and axle beam such that directional stability is impaired 4 X BOLTS LOOSE(MARKED) (5.1.2 (c) (ii)) | 1 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 1 |
| Nearside Rear Brake drum contaminated (1.1.14 (b)) | 1 |
| Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Side repeater missing |1.4.A.2b| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near steering box (5.3.6 (a) (i)) | 1 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Nearside Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
| Offside Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Cross member. (6.1.1 (c) (i)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Front Windscreen wiper not working (3.4 (a)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Service brake excessively fluctuating 60% imbalanced across an axle (1.2.1 (e)) | 1 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
| Brake pedal has insufficient reserve travel |1.1.2 |a|| | 1 |
| Brake pedal not releasing correctly and functionality of brakes affected pedal coming into contact with steering box |1.1.2 |b| |ii|| | 1 |
| Nearside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Front Upper Front suspension has excessive play in a pin or bush of an upper wishbone inner bearing |2.5.B.1a| | 1 |
| Offside Front Upper Front suspension has excessive play in a pin or bush of an upper wishbone inner bearing |2.5.B.1a| | 1 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Rear parking brake recording little or no effort | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer sills marked with chalk |5.3.6 |a| |i|| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer surfaces marked with chalk |5.3.6 |a| |i|| | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer sills
Affected sections marked with chalk |5.3.6 |a| |i|| | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer sills marked with chalk |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Bumper insecure Mounting points corroded marked with chalk |6.1.4 |a| |i|| | 1 |
| Offside Rear Parking |secondary brake| on a single line braking system has inadequate effort at a wheel |1.3.1 |a| |i|| | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Front Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Suspension component modified so the suspension is inoperative (5.3.3 (c) (ii)) | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases multiple exhaust leaks (6.1.2 (a)) | 1 |
| Nearside Front Lower Suspension component pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Lower Suspension component pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Hazard warning switch inoperative only one side working (4.4.2 (a) (ii)) | 1 |
| Front Steering component mounting prescribed area is excessively corroded valance by steering box (2.1.2 (e) (i)) | 1 |
| Nearside Front Axle swivel pins and bushes swivel pin and/or bush excessively worn (5.1.2 (b) (i)) | 1 |
| Offside Rear Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point to sill and outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point to sill and outer sill (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases manifold to head gaskets (6.1.2 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill to wheelarch (7.1.1 (a) (i)) | 1 |
| Offside Rear fog lamp insecure |1.3.2a| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Front Side repeater incorrect colour |1.4.A.2f| | 1 |
| Nearside Rear Lower Exhaust has a major leak of exhaust gases silencer |6.1.2 |a|| | 1 |
| Nearside Side repeater incorrect colour |1.4.A.2f| | 1 |
| Steering damper damaged and unserviceable |2.2.C.1d| | 1 |
| Nearside Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Nearside Front Suspension arm has excessive play in a pin/bearing |2.4.G.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear fog lamp obviously incorrectly positioned |1.3.2a| | 1 |
| Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
| Brake pedal feels spongy with the vacuum fully depleted |3.3.C.2| | 1 |
| Offside Steering box has excessive free play detected at the steering wheel (steering box fitted) (2.3 (a) (i)) | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced crosmember behind bumper (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer to inner seal (6.1.1 (c) (i)) | 1 |
| Steering component casing retaining devices dangerously loose damper bolt (2.1.2 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases both silencers holed (6.1.2 (a)) | 1 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Windscreen wiper blade missing |8.2.2| | 1 |
| Offside Rear fog lamp flickers when tapped lightly by hand |1.1.6d| | 1 |
| Exhaust emissions - engine idle speed too high |8.2.1.2 |e|| | 1 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front Side repeater not working |1.4.A.2c| | 1 |
| Offside Front Side repeater not working |1.4.A.2c| | 1 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 1 |
| Rear Seat belt missing all rear buckles missing |7.1.2 |a|| | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Exhaust has a major leak of exhaust gases At silencer (6.1.2 (a)) | 1 |
| Offside Rear Body panel corroded and likely to cause injury At wheelarch (6.2.1 (a) (i)) | 1 |
| Emissions not tested (8.2.1.2 (d)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak Large hole in backbox pipe. |8.2.1.1 |b|| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at drivers seat mount (5.3.6 (a) (i)) | 1 |
| Rear fog lamp tell-tale missing no switch for rear fog light labeled (4.9.1 (a) (ii)) | 1 |
| Hazard warning switch inoperative no switch for hazards labeled (4.4.2 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure is so weakened by corrosion within 30cm of a towbar mounting, the towbar is likely to become detached At tow bar mount (6.1.6 (i) (ii)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Nearside Side repeater not working |4.4.1 |a| |ii|| | 1 |
| Nearside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Nearside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outrigger (6.1.1 (c) (i)) | 1 |
| Offside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced out rigger (6.1.1 (c) (i)) | 1 |