Most common failures | No# failures |
---|
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 13 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
Registration plate issues | 8 |
Headlamp aim out of alignment | 7 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
Rear brake binding | 6 |
Registration plate lamp issues | 5 |
Windscreen wiper does not clear the windscreen effectively | 5 |
Brake pipe excessively corroded | 5 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Brake hose excessively deteriorated | 5 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
Service brake: efficiency below requirements |3.7.B.7| | 4 |
Parking brake: efficiency below requirements |3.7.B.7| | 4 |
Offside Steering rack gaiter split |2.2.D.2d| | 4 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 4 |
Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
Offside Headlamp not working on dipped beam |1.7.5a| | 3 |
Brakes imbalanced across an axle | 3 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
Horn not working |1.6.2a| | 2 |
Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 2 |
Nearside Front Steering rack gaiter split |2.2.D.2d| | 2 |
Emissions not tested |7.0| | 2 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside front brake binding |3.7.B.1| | 2 |
Offside front brake binding |3.7.B.1| | 2 |
Rear parking brake recording little or no effort | 2 |
Front brake application uneven | 2 |
Nearside Front front brake binding |3.7.B.1| | 2 |
Offside Front Body insecure and dangerous to other road users |6.1.B.1b| | 2 |
Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 2 |
Offside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside rear brake recording little or no effort |3.7.B.5a| | 2 |
Rear Brake pipe inadequately clipped |3.6.B.1| | 2 |
Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
Offside Front Direction indicator not working |1.4.A.2c| | 2 |
Offside Obligatory mirror insecure |8.1.1| | 1 |
Hazard warning lamps inoperative |1.4.B.1b| | 1 |
Nearside Passenger`s seat insecure |6.2.A.1| | 1 |
Nearside Headlamp insecure |1.7.3| | 1 |
Position lamp switch faulty |1.1.A.1| | 1 |
Nearside Front position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Nearside Front Direction indicator excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
Offside Stop lamp not working |1.2.1b| | 1 |
Brake pedal spongy |3.3.B.1b| | 1 |
Nearside Rear Braking system leaking |3.6.A.1| | 1 |
Offside Front Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
Nearside Front Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Front Steering rack gaiter split |2.2.D.2d| | 1 |
Brake pedal anti-slip provision loose |3.3.A.1b| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded inner and outer sills |5.2.6| | 1 |
Offside Suspension component mounting prescribed area is excessively corroded inner and outer sills |2.4.A.3| | 1 |
Headlamp aim not tested |1.8.A.1c| | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Nearside Outer Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Windscreen washer control missing |8.2.1a| | 1 |
Front Windscreen wiper control missing |8.2.1a| | 1 |
Offside Front Headlamp insecure |1.7.3| | 1 |
Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Nearside Rear Coil spring mounting corroded and seriously weakened |2.4.C.3c| | 1 |
Offside Rear Panhard rod attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
Driver`s seat fore and aft adjustment mechanism not functioning as intended. |6.2.A.3| | 1 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Front Steering rack insecure |2.2.B.1a| | 1 |
Nearside Front Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
Offside Front Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
Nearside Front Front passenger seat insecure |6.2.3| | 1 |
All position lamps not working |1.1.A.3b| | 1 |
Offside Headlamp insecure |1.7.3| | 1 |
Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen both (3.5 (a)) | 1 |
Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 1 |
Nearside Rear wheel cylinder leaking |3.6.A.1| | 1 |
Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Centre Rear Exhaust system not adequately supported |7.1.1| | 1 |
Rear Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Rear brake application uneven | 1 |
rear brakes release unevenly |3.7.B.4| | 1 |
Nearside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Rear Panhard rod locating pin locking device not properly locked |2.4.G.3b| | 1 |
Nearside Rear brake caliper securing device missing |3.5.1j| | 1 |
Offside Rear brake caliper securing device missing |3.5.1j| | 1 |
Brake performance not tested |3.7.A.1| | 1 |
Service brake: efficiency below requirements |3.7.C.1a| | 1 |
Parking brake: efficiency below requirements |3.7.C.1b| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
Offside Front Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
Front Lower Suspension arm severely distorted |2.4.G.1| | 1 |
Exhaust emissions hydrocarbon content excessive |8.2.1.2 |b|| | 1 |
Nearside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Headlamp not working on main beam |1.7.5a| | 1 |
Rear Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
Offside Front Lower Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
Nearside Front Suspension component mounting prescribed area is inadequately repaired under bonnet (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under bonnet (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near front shock absorber mounting behind wheel arch (5.3.6 (a) (i)) | 1 |
Passenger`s seat insecure |6.2.A.1| | 1 |
Driver`s seat insecure |6.2.A.1| | 1 |
Nearside Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
Offside Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
Nearside Road wheel fixings not compatible |4.2.B.2| | 1 |
Offside Road wheel fixings not compatible |4.2.B.2| | 1 |
Nearside Rear Suspension spring mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
Nearside Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
Nearside Front suspension locking device ineffective |2.5.A.4| | 1 |
Offside Front Front suspension locking device ineffective |2.5.A.4| | 1 |
Nearside Rear Suspension arm attachment bracket/mounting weld cracked |2.4.G.1| | 1 |
Nearside Rear Upper Suspension arm attachment bracket/mounting weld cracked |2.4.G.1| | 1 |
Rear Suspension arm attachment bracket/mounting insecure |2.4.G.1| | 1 |
Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
Rear Brake pipe kinked |3.6.B.2b| | 1 |
Offside Ball joint has excessive play |2.2.B.1f| | 1 |
Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 1 |
Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Anti-roll bar has excessive play in a pin/bearing |2.4.G.2| | 1 |
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear coil spring incomplete |2.4.C.1a| | 1 |