| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 23 |
| Parking brake: efficiency below requirements |3.7.B.7| | 13 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 12 |
| Registration plate lamp issues | 12 |
| Windscreen wiper does not clear the windscreen effectively | 12 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
| Rear brake binding | 9 |
| Brake pipe excessively corroded | 8 |
| Rear parking brake recording little or no effort | 8 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Brakes imbalanced across an axle | 7 |
| Service brake: efficiency below requirements |3.7.B.7| | 6 |
| Rear brake application uneven | 5 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 5 |
| Brake pedal spongy |3.3.B.1b| | 4 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 4 |
| Brake hose excessively deteriorated | 4 |
| Registration plate issues | 4 |
| Offside Steering rack gaiter split |2.2.D.2d| | 4 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 4 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Offside Front Brake hose stretched |found during steering lock to lock check| |2.2.D.2b| | 3 |
| Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 3 |
| Nearside Stop lamp not working |1.2.1b| | 3 |
| Rear fog lamp not working |1.3.2b| | 3 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 3 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 3 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 3 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 3 |
| Hazard warning switch faulty |1.4.B.1d| | 3 |
| Offside Headlamp not working on main beam |1.7.5a| | 3 |
| Offside Rear fog lamp not working |1.3.2b| | 3 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Battery insecure |1.9.1| | 3 |
| Rear Statutory seat belt missing |5.1.1| | 2 |
| Nearside Front Macpherson strut has excessive movement at the upper attachment |2.5.A.1c| | 2 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Exhaust emits excessive dense blue smoke during acceleration |7.3.A.2c| | 2 |
| Brake hose damaged | 2 |
| Offside Rear Rear wheel bearing has excessive play |2.6.2| | 2 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
| rear brakes release unevenly |3.7.B.4| | 2 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 2 |
| Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 2 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Road wheel bead rim badly distorted |4.2.A.1a| | 2 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 2 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 2 |
| Fuel pipe leaking |7.2.3| | 2 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 2 |
| Brake pedal anti-slip provision missing |3.3.A.1b| | 2 |
| Exhaust engine idle speed too high |7.3.A.2a| | 2 |
| Fuel tank leaking |7.2.3| | 2 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 2 |
| Offside Rear wheel bearing has excessive play |2.6.2| | 2 |
| Rear Exhaust system not adequately supported |7.1.1| | 2 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 2 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front front brake binding |3.7.B.1| | 2 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Shock absorber has negligible damping effect |2.7.5| | 2 |
| Offside Front Shock absorber has negligible damping effect |2.7.5| | 2 |
| Offside Stop lamp not working |1.2.1b| | 2 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 2 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Horn not working |1.6.2a| | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Headlamp does not operate immediately when selected on main beam |1.7.4a| | 2 |
| Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Offside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Nearside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Front brake caliper leaking |3.6.A.1| | 1 |
| Nearside Rear Service brake application uneven across the axle |3.7.D.2b| | 1 |
| Centre Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Outer Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Outer Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen |3.5 |a|| | 1 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
| Nearside Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Nearside Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Brake hose bulging under pressure |3.6.B.3| | 1 |
| Offside Front Brake hose bulging under pressure |3.6.B.3| | 1 |
| Nearside Front coil spring broken |2.4.C.1a| | 1 |
| Nearside Front Direction indicator insecure |1.4.A.2b| | 1 |
| Bonnet cannot be secured in the closed position |8.4.1| | 1 |
| Offside Headlamp insecure |1.7.3| | 1 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Rear coil spring incomplete |2.4.C.1a| | 1 |
| Nearside Front Headlamp insecure |1.7.3| | 1 |
| Nearside Front Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Obligatory mirror missing |8.1.1| | 1 |
| Emissions not tested |7.3.A.1| | 1 |
| Front Horn not working |1.6.2a| | 1 |
| Rear Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
| Offside Front Lower Steering locking device missing |2.2.C.1g| | 1 |
| Offside Front coil spring fractured |2.4.C.1a| | 1 |
| Front Brake performance not tested |3.7.A.1| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Offside Rear Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Offside Parking brake: efficiency below requirements |3.7.B.7| | 1 |
| Offside Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill carroded holed |2.4.A.3| | 1 |
| Track rod end loose both front |2.2.B.1d| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded under wheel arch |2.4.A.3| | 1 |
| Offside Front Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Brake pedal has insufficient reserve travel |1.1.2 |a|| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Direction indicator not working both rear |1.4.A.2c| | 1 |
| Offside Front Suspension component mounting prescribed area is severely distorted |2.4.A.3| | 1 |
| Parking brake lever pawl spring does not push the pawl positively into the ratchet teeth |3.1.5| | 1 |
| Nearside Front Track rod end loose |2.2.B.1d| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Centre Front Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
| Exhaust emits dense blue smoke at idle |7.3.A.2b| | 1 |
| Emissions not tested |7.0| | 1 |
| Nearside Brake pipe leaking |3.6.A.1| | 1 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Outer Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Outer Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Headlamp switch faulty |1.7.1| | 1 |
| Parking brake lever defective so that it cannot be satisfactorily operated |3.1.3c| | 1 |
| Offside Front brake caliper leaking |3.6.A.1| | 1 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Headlamp not in good working order |not working| |1.2.4a| | 1 |
| Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Brake has no servo assistance |3.3.B.2| | 1 |
| Brake pedal anti-slip provision loose |3.3.A.1b| | 1 |
| Parking brake lever insecure |3.1.3b| | 1 |
| Offside Front suspension has a suspension lower ball joint securing nut not locked |2.5.B.1a| | 1 |
| Fuel hose leaking |7.2.3| | 1 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| An item not tested |Manual| | 1 |
| Offside Rear fog lamp missing |1.3.2a| | 1 |
| Mechanical brake component has restricted free movement | 1 |
| Nearside Front An item not tested |Manual| | 1 |
| Rear Mechanical brake component has restricted free movement | 1 |
| Offside Rear Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Offside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Offside Front Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Side repeater not working |1.4.A.2c| | 1 |
| Offside Front Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Offside Front Macpherson strut has excessive movement at the upper attachment |2.5.A.1c| | 1 |
| Nearside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Rear Fuel system component leaking |7.2.3| | 1 |
| Front brake application uneven | 1 |
| Offside Front front brake binding |3.7.B.1| | 1 |
| Nearside Rear Braking system leaking |3.6.A.1| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Brake pipe leaking |3.6.A.1| | 1 |
| Nearside Front Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Brake performance not tested |3.7.A.1| | 1 |
| Offside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Nearside Outer Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside Rear Body has a projection caused by damage |6.1.C.1| | 1 |
| Nearside Rear Body has a projection caused by damage |6.1.C.1| | 1 |
| Nearside Front Lower Suspension arm attachment bracket/mounting corroded and seriously weakened arm mounting point (5.3.3 (b) (i)) | 1 |
| Offside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Front Direction indicator not working |1.4.A.2c| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |7.1.4| | 1 |
| Offside Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Headlamp aim not tested |1.8.A.1c| | 1 |
| Nearside Windscreen wiper blade missing |8.2.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Nearside Rear passenger seat cannot be secured in the upright position. |6.2.3| | 1 |
| Offside Rear passenger seat cannot be secured in the upright position. |6.2.3| | 1 |
| Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Rear Brake pipe leaking |3.6.A.1| | 1 |
| Nearside Front Suspension arm locating pin locking device missing |2.4.G.3b| | 1 |
| Parking brake lever ratchet mechanism is broken |3.1.5| | 1 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Nearside Rear Upper Shock absorber detached |2.7.2b| | 1 |
| Nearside Rear Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Front Brake hose stretched |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
| Nearside Headlamp insecure |1.7.3| | 1 |
| Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Headlamp does not operate immediately when selected on dipped beam electrical fault glows dim |1.7.4a| | 1 |
| Nearside Front Direction indicator adversely affected by the operation of another lamp with headlight |1.4.A.2h| | 1 |
| Parking brake lever has no reserve travel disconnected |3.1.6b| | 1 |
| Fuel tank insecure fuel tank is a drinks bottle , loose in scuttle , fowled by wiper linkage |7.2.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill within 30cm of trailing arm mounting |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner sill and floor at "B" pillar within 30cm of seatbelt mounting |5.2.6| | 1 |
| Brake cable insecure disconnected from parking brake |3.5.1d| | 1 |
| Exhaust emissions hydrocarbon content excessive engine has a miss fire and not operating correctly |7.3.B.1b| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Headlamp aim not tested |1.8.A.1c| | 1 |
| Offside Headlamp aim not tested |1.8.A.1c| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Offside Rear Seat belt missing |7.1.2 |a|| | 1 |
| Exhaust emissions carbon monoxide content excessive |8.2.1.2 |b|| | 1 |
| Body panel likely to become detached offside front wing |6.2.1 |a| |ii|| | 1 |
| Offside Front Body panel corroded and likely to cause injury wing |6.2.1 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension arm mounting |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension arm mounting |5.3.6 |a| |i|| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Front Body panel corroded and likely to cause injury wheel arch and wing |6.2.1 |a| |i|| | 1 |
| Oil leaking excessively from engine |8.4.1 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Headlamp does not operate immediately when selected on dipped beam |1.7.4a| | 1 |
| Nearside Front Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Exhaust has a major leak of exhaust gases rear section on joints |7.1.2| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded in end of sill |2.4.A.3| | 1 |
| Offside Front brake disc contaminated by oil |3.5.1h| | 1 |
| Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |