| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 25 |
| Brake pipe excessively corroded | 21 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 17 |
| Headlamp aim out of alignment | 15 |
| Registration plate lamp issues | 13 |
| Brake hose excessively deteriorated | 13 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 8 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 8 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 7 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 7 |
| Offside Rear fog lamp not working |1.3.2b| | 6 |
| Offside Rear Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 5 |
| Drivers seat fore and aft adjustment mechanism not functioning as intended. (6.2.5 (b) (i)) | 5 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
| Anti-lock braking system warning lamp indicates an ABS fault | 4 |
| Nearside Front Shock absorbers has a serious fluid leak | 4 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
| Brakes imbalanced across an axle | 4 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 4 |
| Offside Stop lamp not working |1.2.1b| | 4 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 3 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 3 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 2 |
| Nearside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 2 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Front Windscreen wiper not working (3.4 (a)) | 2 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 2 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Nearside Rear Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Nearside Rear Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 2 |
| Offside Rear Shock absorbers has a serious fluid leak | 2 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 2 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Nearside Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 2 |
| Offside Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 2 |
| Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 2 |
| Nearside Front Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 2 |
| Rear fog lamp not working (1.3.2b) | 2 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 2 |
| Emissions not tested |7.0| | 2 |
| Registration plate issues | 2 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 2 |
| Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 2 |
| Speedometer cannot be illuminated (7.8 (c) (ii)) | 2 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Electrical wiring insecure and connectors likely to become disconnected upper engine earth lead (4.11 (a) (ii)) | 1 |
| Nearside Front Service brake lagging in operation (1.2.1 (d)) | 1 |
| Front Upper Suspension arm ball joint excessively worn o/s and n/s upper ball joints (5.3.4 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases front box blowing (6.1.2 (a)) | 1 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt inner boot (6.1.7 (g) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases blowing at front pipe (6.1.2 (a)) | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Exhaust system insecure tail pipe corroded at central joint (6.1.2 (a)) | 1 |
| Emissions unable to be completed (8.2.2.2 (e)) | 1 |
| Offside Front Anti-roll bar linkage missing (5.3.3 (a) (ii)) | 1 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 1 |
| Nearside Rear Stop lamp(s) emits other than a steady red light damaged lens (4.3.3 (a) (ii)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis support legs (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis support legs (6.1.1 (c) (i)) | 1 |
| Windscreen washer not working | 1 |
| Brake hydraulic reservoir cap missing (1.1.10 (e)) | 1 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
| Emissions unable to be completed exhaust incomplete (8.2.2.2 (e)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced undersill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Trailer electrical socket (13 pin) not functioning at all (4.10 (c) (ii)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area (5.3.6 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i)) | 1 |
| Trailer electrical socket wiring insulation damaged or deteriorated and likely to cause a short-circuit (4.10 (b) (ii)) | 1 |
| Rear Brake valve insecure (1.1.7 (c)) | 1 |
| Rear Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Nearside Rear Position lamp with a multiple light source more than 1/2 not functioning (4.2.1 (a) (ii)) | 1 |
| Offside Rear Shock absorbers insecurely attached snapped at bottom mounting (5.3.2 (a) (i)) | 1 |
| Front Lower Exhaust has a major leak of exhaust gases pipe (6.1.2 (a)) | 1 |
| Exhaust has a major leak of exhaust gases middle box (6.1.2 (a)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt inner x2 pin bush covers (5.3.4 (b) (ii)) | 1 |
| Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt inner x2 pin bush (5.3.4 (b) (ii)) | 1 |
| Central Prop shaft bearing excessively worn (6.1.7 (b) (i)) | 1 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b)) | 1 |
| Rear Brake load sensing valve linkage defective and function impaired (1.1.17 (a)) | 1 |
| Front Prop shaft joint so worn it is likely to fail Worn Through Front Flange Casting (6.1.7 (c) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Offside Front Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Nearside Front Brake hose connection leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 1 |
| Nearside Side repeater lens defective such that the emitted light is adversely affected SIDE REPEATER (4.4.1 (b) (ii)) | 1 |
| Brake load sensing valve seized but ABS functioning (1.1.17 (c) (i)) | 1 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Brake load sensing valve inoperative and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases centre (6.1.2 (a)) | 1 |
| Offside Front Hydraulic brake calliper leaking (1.1.16 (b) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Front Integral body structure is fractured and structural rigidity is significantly reduced sill (6.1.1 (a) (i)) | 1 |
| Nearside Rear Integral body structure is fractured and structural rigidity is significantly reduced Wheel arch (6.1.1 (a) (i)) | 1 |
| Offside Rear Integral body structure is fractured and structural rigidity is significantly reduced Wheel arch (6.1.1 (a) (i)) | 1 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 1 |
| Nearside Rear Outer Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Rear Exhaust has a major leak of exhaust gases pipe & box (6.1.2 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Front Brake hose excessively stretched (1.1.12 (b) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage missing (5.3.3 (a) (ii)) | 1 |
| Nearside Rear Direction indicator incorrect colour lens damaged so flashing white light (4.4.3 (a)) | 1 |
| Rear fog lamp missing Broken (4.5.1 (a) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Outer Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Brake load sensing valve inoperative but ABS functioning (1.1.17 (c) (i)) | 1 |
| Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 1 |
| Steering system excessively rough (2.1.1 (a)) | 1 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt little end (2.1.3 (g) (ii)) | 1 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt little end (2.1.3 (g) (ii)) | 1 |
| Offside Rear Rear position lamp(s) excessively deteriorated so that it is not visible from a reasonable distance (1.1.A.3d) | 1 |
| Nearside Front constant velocity joint gaiter split (2.5.C.1a) | 1 |
| Offside Front constant velocity joint gaiter insecurely mounted to its housing (2.5.C.1a) | 1 |
| Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a) | 1 |
| Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
| Front Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
| Nearside Rear Shock absorber has an excessively worn bush (2.7.4) | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Centre Front Obligatory mirror missing (8.1.1) | 1 |
| Nearside Front position lamp(s) not working (1.1.A.3b) | 1 |
| Nearside Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Offside Rear Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Nearside Front Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction Garland (3.1 (a) (ii)) | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Stop lamp(s) with a multiple light source more than 1/2 not functioning (4.3.1 (a) (ii)) | 1 |
| Central Exhaust has a major leak of exhaust gases Silencer/multiple leaks (6.1.2 (a)) | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Upper Shock absorbers insecurely attached Mounting lose (5.3.2 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x2 (5.3.6 (a) (i)) | 1 |
| Offside Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Outer Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Service brake: efficiency below requirements |3.7.C.1a| | 1 |
| Nearside Front Upper Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Upper Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Seat belt retracting mechanism defective not retracting (7.1.2 (e)) | 1 |
| Front Electrical wiring insulation in such a condition there is an imminent risk of fire or formation of sparks connected to battery (4.11 (c) (iii)) | 1 |
| Nearside Front Upper Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Upper Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Exhaust has a major leak of exhaust gases front flexible pipe (6.1.2 (a)) | 1 |
| Central Front Undertray likely to become detached (6.2.1 (a) (ii)) | 1 |
| Offside Front Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases front pipe ( long section ) (6.1.2 (a)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
| Nearside Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired cill (6.2.2 (d) (ii)) | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill (6.2.2 (d) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Rear fog lamp obviously incorrectly positioned (4.5.4 (a)) | 1 |
| Rear Position lamp not working both (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill closing panel holed at suspension mounting area (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases rear silencer pipe badly holed and blowing (6.1.2 (a)) | 1 |
| Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction (3.1 (a) (ii)) | 1 |
| Stop lamp(s) not working high level (4.3.1 (a) (ii)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension trailing arm mounting (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension trailing arm mount (5.3.6 (a) (i)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill section (7.1.1 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Prop shaft joint excessively worn (6.1.7 (c) (i)) | 1 |
| Drivers airbag missing (7.1.5 (a)) | 1 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill has various holes (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Jacking point holed / inner sill holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced rear inner panel between wheel and bumper holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed close to wishbone mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Inner Sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Emissions not tested due to oil leak (8.2.2.2 (e)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced near spring (6.1.1 (c) (i)) | 1 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis rail inside wheel arch (6.1.1 (c) (ii)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced front and rear inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outer sill (7.1.1 (a) (i)) | 1 |
| Exhaust emits clearly visible black smoke during acceleration (8.2.1.2 (g)) | 1 |
| Nearside Brake pipe at imminent risk of failure or fracture Front to rear (1.1.11 (a)) | 1 |
| Offside Brake pipe at imminent risk of failure or fracture Front to rear (1.1.11 (a)) | 1 |
| Brake performance not tested (1.2.1 (g)) | 1 |
| Nearside Front Cab steps in such a condition that it is likely to cause injury step inner and outer areas holed and corroded away, AS MARKED (6.2.8 (b)) | 1 |
| Offside Front Cab steps in such a condition that it is likely to cause injury step inner and outer areas holed and corroded away, AS MARKED (6.2.8 (b)) | 1 |
| Offside Front Bumper insecure (6.1.4 (a) (i)) | 1 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Emissions unable to be completed unknown timing belt history.interval light on on dash (8.2.2.2 (e)) | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Oil leaking excessively from engine turbo oil return pipe (8.4.1 (a) (i)) | 1 |
| Offside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Speedometer clearly inoperative (7.8 (b) (ii)) | 1 |
| Stop lamp not working |1.2.1b| | 1 |
| Offside Steering system has a road wheel fouling a part of the vehicle |2.2.D.2a| | 1 |
| Centre Rear Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Horn control missing |1.6.1| | 1 |
| Offside Front Wheel nut|s| missing |4.2.A.1e| | 1 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.4.B.1| | 1 |
| Offside Headlamps matched pair are not the same colour |1.7.6| | 1 |
| Headlamp aim not tested (4.1.2 (b)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Rear Inner Stop lamp(s) light intensity significantly reduced (4.3.3 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jacking point (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Shock absorbers insecurely attached (5.3.2 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced SILL CORRODED (7.1.1 (a) (i)) | 1 |
| Supplementary restraint system warning lamp indicates a fault airbag light is on (7.1.6 (a)) | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Rear fog lamp not working |1.3.2b| | 1 |
| Offside Outer Stop lamp not working |1.2.1b| | 1 |
| Nearside Front Upper Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Offside Obligatory mirror insecure |8.1.1| | 1 |
| Offside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Nearside Stop lamp not working |1.2.1b| | 1 |
| Centre Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Central Rear Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Large hole on inner sill panel, also holes on outer (6.1.1 (c) (i)) | 1 |
| Brake load sensing valve linkage defective and function impaired (1.1.17 (a)) | 1 |