| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 9 |
| Headlamp aim out of alignment | 8 |
| Registration plate lamp issues | 6 |
| Brake pipe excessively corroded | 5 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Horn not working |1.6.2a| | 4 |
| Parking brake: efficiency below requirements |3.7.B.7| | 4 |
| Rear brake binding | 4 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 4 |
| Rear parking brake recording little or no effort | 3 |
| Brake load sensing valve seized |3.6.E.3| | 3 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Battery insecure |1.9.1| | 3 |
| Horn not working (7.7 (a)) | 3 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Rear wheel bearing rough when rotated |2.6.1| | 2 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Headlamp not working on main beam |1.7.5a| | 2 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
| Offside Rear fog lamp not working |1.3.2b| | 2 |
| Exhaust system not adequately supported |7.1.1| | 2 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 2 |
| Front Fuel system component leaking by in line fuel filter |7.2.3| | 1 |
| Exhaust system not adequately supported tail pipe o rings missing |7.1.1| | 1 |
| Rear brake application uneven | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Exhaust system not adequately supported all rubbers split perished and some missing |7.1.1| | 1 |
| Nearside Front Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded spring rear mounting inner sill area marked yellow |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded rear spring rear mounting outer sill area marked yellow |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded rear spring rear mounting outer sill area marked yellow |2.4.A.3| | 1 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis at rearmost spring hanger mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis at rearmost spring hanger mount (5.3.6 (a) (i)) | 1 |
| Nearside Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Direction indicators flashing more than 120 times a minute |1.4.A.2g| | 1 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
| Exhaust system not adequately supported rubber o ring mount rubbers missing and 1 almost split through |7.1.1| | 1 |
| Offside Headlamp has a product on the light source so that the light output is severely reduced full of water affecting beam image |1.7.5a| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 1 |
| Nearside Battery insecure |1.9.1| | 1 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Headlamp not working on main beam both |1.7.5a| | 1 |
| Nearside Stop lamp not working |1.2.1b| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt both outer (6.1.7 (g) (ii)) | 1 |
| Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch (6.2.2 (d) (i)) | 1 |
| Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 1 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Electrical wiring insecure |1.9.2a| | 1 |
| Offside Headlamp insecure |1.7.3| | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Headlamp insecure (4.1.1 (c)) | 1 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Central Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Battery insecure and likely to fall from carrier Main battery at Offside inner wing (4.13 (a) (ii)) | 1 |
| Offside Rear Seat belt not functioning as intended outer belt not unwinding ( jammed ) (7.1.2 (c)) | 1 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Offside Front Brake pipe fouled by moving parts |3.6.B.2a| | 1 |
| Brake pipe leaking on an air braking system front to rear |1.1.11 |b| |i|| | 1 |
| Horn not working |7.7 |a| |ii|| | 1 |
| Brake performance not tested System leaking |1.2.1 |g|| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Offside Side repeater not working |4.4.1 |a| |ii|| | 1 |
| Brakes imbalanced across an axle | 1 |
| Windscreen washer not working | 1 |
| Front Exhaust mounting missing |7.1.1b| | 1 |
| Registration plate issues | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Position lamp not working |4.2.1 |a|| | 1 |
| Front Headlamp not working on dipped beam both not working on main beam |4.1.1 |a| |ii|| | 1 |
| Rear Leaf spring seriously weakened both |5.3.1 |b| |i|| | 1 |
| Front Shock absorbers has a serious fluid leak both |5.3.2 |b|| | 1 |
| Nearside Inner Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Outer Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Inner Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Outer Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Service brake grabbing severely (1.2.1 (c)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front crossmember tie bar mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill area (7.1.1 (a) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting center |6.2.2 |d| |i|| | 1 |
| Engine mounting bracket damaged or deteriorated resulting in excessive movement bolt missing |6.1.8 |a| |i|| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill outer |6.1.1 |c| |i|| | 1 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
| Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
| Nearside Front Electrical wiring damaged and bare wires exposed |1.9.2c| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 1 |
| Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Nearside Electrical wiring insecure and connectors likely to become disconnected battery terminal (4.11 (a) (ii)) | 1 |
| Offside Front Upper Brake pipe leaking on an air braking system (1.1.11 (b) (i)) | 1 |
| Central Brake pipe leaking on an air braking system front to rear section (1.1.11 (b) (i)) | 1 |
| Brake performance unable to be tested brake pipes leaking (1.2.1 (g)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced chassis corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Nearside Headlamp insecure |4.1.1 |c|| | 1 |
| Offside Headlamp insecure |4.1.1 |c|| | 1 |
| Exhaust emissions carbon monoxide content excessive |8.2.1.2 |b|| | 1 |