Most common failures | No# failures |
---|
Headlamp aim out of alignment | 22 |
Brake pipe excessively corroded | 14 |
Windscreen wiper does not clear the windscreen effectively | 9 |
Rear brake binding | 8 |
Brake hose excessively deteriorated | 6 |
Brakes imbalanced across an axle | 6 |
Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Exhaust system not adequately supported |7.1.1| | 5 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
Registration plate lamp issues | 4 |
Parking brake: efficiency below requirements |3.7.B.7| | 4 |
Battery insecure |1.9.1| | 4 |
Offside Front position lamp|s| not working |1.1.A.3b| | 4 |
Nearside Headlamp not working on main beam |1.7.5a| | 3 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Rear parking brake recording little or no effort | 3 |
Centre Exhaust system not adequately supported |7.1.1| | 3 |
Registration plate issues | 3 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 3 |
Offside Side repeater not working |1.4.A.2c| | 3 |
Nearside Front Direction indicator not working |1.4.A.2c| | 2 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 2 |
Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Offside Headlamp insecure |1.7.3| | 2 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
Nearside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 2 |
Rear Exhaust system not adequately supported |7.1.1| | 2 |
Nearside Headlamp insecure |1.7.3| | 2 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Offside Front Headlamp insecure |1.7.3| | 2 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Service brake efficiency below requirements |1.2.2 |a| |i|| | 2 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 2 |
Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Electrical wiring damaged and bare wires exposed |1.9.2c| | 2 |
Nearside Stop lamp not working |1.2.1b| | 2 |
Nearside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 2 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Rear Direction indicator incomplete |1.5.A1b| | 2 |
Brake has no servo assistance |3.3.B.2| | 1 |
Fuel system component leaking |7.2.3| | 1 |
Offside Front Brake pipe inadequately supported |3.6.B.1| | 1 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings door step |6.1.B.2| | 1 |
Nearside Front Upper Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings inner wing |6.1.B.2| | 1 |
Nearside Front Lower Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings inner wing |6.1.B.2| | 1 |
Offside Front Lower Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings inner wing |6.1.B.2| | 1 |
Offside Rear Shock absorber casing damaged externally so the unit does not function advise change both |2.7.2a| | 1 |
Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
Offside Front Direction indicator not working |1.4.A.2c| | 1 |
Spare wheel insecure |6.4.2| | 1 |
Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
Rear Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Headlamp aim not tested (4.1.2 (b)) | 1 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Offside Front Brake hose excessively damaged (1.1.12 (b) (ii)) | 1 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Offside Inner Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Outer Rear Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Inner Rear Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Outer Rear Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner and outer sill |2.4.A.3| | 1 |
Nearside Front Front constant velocity joint is excessively worn |2.5.C.1b| | 1 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
Offside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Nearside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Exhaust system insecure mountings broken |6.1.2 |a|| | 1 |
Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Exhaust mounting missing |7.1.1b| | 1 |
Nearside Upper Front position lamp|s| not working |1.1.A.3b| | 1 |
Offside Front Upper Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear Upper Front position lamp|s| not working |1.1.A.3b| | 1 |
Offside Front Inner Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
Emissions not tested over heated and leaked out its coolant |8.2.1.2 |d|| | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Fuel cap/sealing device ineffective temp cap fiited and seal torn |6.1.3 |b| |i|| | 1 |
Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
Front Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
Brake pedal anti-slip provision worn smooth |3.3.A.1b| | 1 |
Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Nearside Indicator tell tale inoperative |1.4.A.2a| | 1 |
Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
Leaf spring has excessive side play at eye |shackle| |2.4.B.4| | 1 |
Offside Battery insecure |1.9.1| | 1 |
Battery insecure and likely to fall from carrier x2 |4.13 |a| |ii|| | 1 |
Windscreen wiper not working |3.4 |a|| | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
Nearside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
Headlamp not working on main beam |1.7.5a| | 1 |
Nearside front brake recording little or no effort |3.7.B.5a| | 1 |
Service brake: efficiency below requirements |3.7.B.7| | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt insecure (6.1.7 (g) (ii)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
Front brake application uneven | 1 |
Offside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Stop lamp not working |1.2.1b| | 1 |
Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Front brake disc in such a condition that it is seriously weakened | 1 |
Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Exhaust has a major leak of exhaust gases manifold |6.1.2 |a|| | 1 |
Nearside Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 1 |
Offside Rear Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
Nearside Rear Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
Offside Rear Service brake excessively fluctuating |1.2.1 |e|| | 1 |
Electrical wiring inadequately supported |1.9.2a| | 1 |
Electrical wiring insecure |1.9.2a| | 1 |
Rear Mechanical brake component has restricted free movement | 1 |
Offside Front Brake hose twisted |3.6.B.4c| | 1 |
Centre Mechanical brake component securing device missing |3.5.1i| | 1 |
Centre Exhaust mounting missing |7.1.1b| | 1 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings near jacking point |6.1.B.2| | 1 |
Position lamp switch insecure |1.1.A.1| | 1 |
Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
Nearside Rear Leaf spring shackle bracket corroded and seriously weakened |2.4.B.6d| | 1 |
Offside Rear Leaf spring shackle bracket corroded and seriously weakened |2.4.B.6d| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner wheel arch |6.1.B.2| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner wheel arch |6.1.B.2| | 1 |
Offside Side repeater incorrect colour |1.4.A.2f| | 1 |
Nearside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Headlamp aim beam image kick up to the offside |1.8| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wheel arch |6.1.B.2| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill ahead of wheel arch , marked (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill ahead of wheel arch , marked (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Panel to rear of shackle mounting , marked (5.3.6 (a) (i)) | 1 |
Nearside Front Position lamp not working |4.2.1 |a|| | 1 |
Nearside Rear position lamp|s| not in a clean condition and function impaired |1.1.4a| | 1 |
Nearside Rear Braking system leaking |3.6.A.1| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded door step |5.2.6| | 1 |
Offside Front Parking brake mechanism/associated mounting prescribed area is excessively corroded door step |3.1.9| | 1 |
Rear fog lamp tell tale not working |1.3.1b| | 1 |
Offside Rear fog lamp not working |1.3.2b| | 1 |
Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Fuel pipe leaking |7.2.3| | 1 |
Offside Stop lamp emits other than a steady red light |1.2.1e| | 1 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Front Lower Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |