| Most common failures | No# failures |
|---|
| Registration plate lamp issues | 7 |
| Headlamp aim out of alignment | 2 |
| Centre Exhaust system not adequately supported |7.1.1| | 2 |
| Rear parking brake recording little or no effort | 2 |
| Rear Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
| Windscreen wiper does not clear the windscreen effectively | 2 |
| Offside Front Side repeater not working |1.4.A.2c| | 2 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 2 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
| Nearside Outer Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Offside Outer Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Headlamp aim beam image too far to the right |1.6.B4| | 1 |
| Offside Headlamp aim beam image too far to the right |1.6.B4| | 1 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Parking brake: efficiency below requirements |3.7.B.7| | 1 |
| Driver`s seat insecure |6.2.A.1| | 1 |
| Front passenger seat insecure |6.2.3| | 1 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front Side repeater not working |1.4.A.2c| | 1 |
| Offside Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Inner Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch (6.2.2 (d) (i)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting behind bumper (6.2.2 (d) (i)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases various places (6.1.2 (a)) | 1 |
| Emissions not tested not running correctly smells of fuel (8.2.1.2 (d)) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Rear brake application uneven | 1 |
| Brake hose excessively deteriorated | 1 |
| Offside Inner Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear An item not tested |Manual| | 1 |
| Nearside Front Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Offside Front Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Nearside Front Headlamp insecure |1.7.3| | 1 |