| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 60 |
| Windscreen wiper does not clear the windscreen effectively | 38 |
| Registration plate lamp issues | 37 |
| Brake pipe excessively corroded | 22 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 20 |
| Parking brake: efficiency below requirements |3.7.B.7| | 19 |
| Nearside Headlamp insecure |1.7.3| | 17 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 17 |
| Rear brake binding | 17 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 16 |
| Offside Rear fog lamp not working |1.3.2b| | 16 |
| Brakes imbalanced across an axle | 15 |
| Horn not working |1.6.2a| | 15 |
| Exhaust system not adequately supported |7.1.1| | 15 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 13 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 12 |
| Offside Headlamp not working on main beam |1.7.5a| | 11 |
| Battery insecure |1.9.1| | 11 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 10 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 10 |
| Service brake: efficiency below requirements |3.7.B.7| | 10 |
| Nearside Headlamp not working on main beam |1.7.5a| | 9 |
| Brake load sensing valve linkage seized |3.6.E.3| | 9 |
| Offside Headlamp insecure |1.7.3| | 9 |
| Offside Stop lamp not working |1.2.1b| | 9 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 9 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| Brake hose excessively deteriorated | 8 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 7 |
| Exhaust mounting missing |7.1.1b| | 7 |
| Registration plate issues | 7 |
| Rear parking brake recording little or no effort | 7 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 7 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 7 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 7 |
| Driver`s seat insecure |6.2.A.1| | 6 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 6 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 6 |
| Rear fog lamp tell tale not working |1.3.1b| | 6 |
| Rear fog lamp not working |1.3.2b| | 5 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 5 |
| Centre Exhaust system not adequately supported |7.1.1| | 5 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 5 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 5 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 5 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 5 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Nearside Stop lamp not working |1.2.1b| | 5 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 5 |
| Rear brake application uneven | 4 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 4 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Offside Front Direction indicator not working |1.4.A.2c| | 4 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 4 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Centre Exhaust mounting missing |7.1.1b| | 4 |
| Nearside Side repeater not working |1.4.A.2c| | 4 |
| Rear Exhaust system not adequately supported |7.1.1| | 4 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 3 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Direction indicators not working |1.4.A.2c| | 3 |
| Offside Side repeater not working |1.4.A.2c| | 3 |
| Nearside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 3 |
| Nearside Front Headlamp insecure |1.7.3| | 3 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 3 |
| Offside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 3 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
| Hazard warning lamps inoperative |1.4.B.1b| | 3 |
| Offside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 3 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 3 |
| Offside Rear Braking system leaking |3.6.A.1| | 3 |
| Brake pedal creeps down when held under pressure |3.3.B.1a| | 3 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Brake load sensing valve seized |3.6.E.3| | 3 |
| Emissions not tested |7.0| | 3 |
| Offside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Rear Exhaust mounting missing |7.1.1b| | 3 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 3 |
| Nearside Headlamp insecure |4.1.1 |c|| | 2 |
| Offside Headlamp insecure |4.1.1 |c|| | 2 |
| Battery insecure and likely to fall from carrier |4.13 |a| |ii|| | 2 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 2 |
| Parking brake lever has no reserve travel |3.1.6b| | 2 |
| Parking brake lever insecure |3.1.3b| | 2 |
| Offside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 2 |
| Nearside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 2 |
| Nearside Rear Brake pipe inadequately clipped |3.6.B.1| | 2 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Front Exhaust mounting missing |7.1.1b| | 2 |
| Offside Rear Leaf spring splayed and action impaired |2.4.B.1c| | 2 |
| Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 2 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 2 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 2 |
| Steering column top mounting bracket insecure |2.1.2d| | 2 |
| Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 2 |
| Headlamp switch insecure |1.7.1| | 2 |
| Nearside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch |6.1.B.2| | 2 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 2 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
| Driver`s seat cannot be secured in the upright position. |6.2.A.2| | 2 |
| Nearside Front Passenger`s seat insecure |6.2.A.1| | 2 |
| Hazard warning switch faulty |1.4.B.1d| | 2 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 2 |
| Horn not loud enough to be heard by another road user |1.6.2b| | 2 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 2 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
| Nearside Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 2 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 2 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 2 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 2 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Nearside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
| Direction indicators not working |1.4.A.2c| | 2 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 2 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 2 |
| Offside Outer Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
| Front brake disc in such a condition that it is seriously weakened | 2 |
| Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 2 |
| Front brake disc excessively pitted |3.5.1h| | 2 |
| Windscreen wiper blade insecure | 2 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Offside Rear wheel bearing has excessive play |2.6.2| | 2 |
| Offside Upper Front position lamp|s| not working |1.1.A.3b| | 2 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 2 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
| Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Rear fog lamp missing |4.5.1 |a| |ii|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis |5.3.6 |a| |i|| | 1 |
| Parking brake mechanism/associated mounting prescribed area is excessively corroded |1.1.21 |e| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired chassis |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired inner wing |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired inner wing |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Nearside Rear Leaf spring shackle bracket corroded and seriously weakened (5.3.1 (b) (i)) | 1 |
| Offside Front Brake hose excessively damaged (1.1.12 (b) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength top strut mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength behind front bumper (5.3.6 (a) (i)) | 1 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Stop lamp not working |1.2.1b| | 1 |
| Offside rear parking |secondary| brake grabbing severely |3.7.B.6b| | 1 |
| Fuel cap/sealing device missing |7.2.4a| | 1 |
| Nearside Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Brake lever has restricted free movement |3.5.1k| | 1 |
| Nearside Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Steering rack gaiter insecure |2.2.D.2d| | 1 |
| Offside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Nearside Front Battery insecure |1.9.1| | 1 |
| Offside Front Battery insecure |1.9.1| | 1 |
| Nearside Direction indicator not working |1.4.A.2c| | 1 |
| Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Offside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
| Offside Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt Split (6.1.7 (g) (ii)) | 1 |
| Front Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced under wing (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outter sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point/ outrigger (6.1.1 (c) (i)) | 1 |
| Nearside Inner Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Nearside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Offside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Nearside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheelarch |6.1.B.2| | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis |6.1.B.2| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings middle out rigger |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings middle out rigger |6.1.B.2| | 1 |
| Nearside Inner Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Rear fog lamp switch missing |1.3.1a| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Nearside Inner Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front Headlamp insecure |1.7.3| | 1 |
| Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Offside Front Valve stem seriously damaged |4.1.D.1e| | 1 |
| Nearside Outer Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Side repeater incorrect colour |1.4.A.2f| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Offside Front Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Front brake disc excessively scored |3.5.1h| | 1 |
| Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Brake pedal spongy |3.3.B.1b| | 1 |
| Nearside Inner Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Offside Outer Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Front brake excessively fluctuating | 1 |
| Nearside Front All position lamps not working |1.1.A.3b| | 1 |
| Parking brake lever, pawl mechanism pivots or their associated mountings are insecure |3.1.4b| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded under floor/inner sill area |5.2.6| | 1 |
| Nearside Front Upper Seat belt anchorage prescribed area is excessively corroded b pillar/outer |5.2.6| | 1 |
| Offside Front Upper Seat belt anchorage prescribed area is excessively corroded b pillar/outer |5.2.6| | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength outrigger x2 |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength outrigger |5.3.6 |a| |i|| | 1 |
| Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
| Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
| Main beam `tell-tale` not working |1.7.4c| | 1 |
| Nearside Front Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outrigger |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outrigger |5.2.6| | 1 |
| Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Front position lamp|s| not working and offside |1.1.A.3b| | 1 |
| Nearside Side repeater not working and offside |1.4.A.2c| | 1 |
| Exhaust system not adequately supported rubber mount broke |7.1.1| | 1 |
| Offside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Side repeater insecure |1.4.A.2b| | 1 |
| Nearside Front Coil spring not correctly located |2.4.C.2| | 1 |
| Offside Front Coil spring not correctly located |2.4.C.2| | 1 |
| Nearside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Headlamp not in good working order |not working| |1.2.4a| | 1 |
| Nearside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Outer Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Front Direction indicators not working |1.4.A.2c| | 1 |
| Rear Stop lamp not working |1.2.1b| | 1 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Offside Headlamp not in a clean condition affecting beam image |1.2.4a| | 1 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside front brake juddering severely |3.7.A.2b| | 1 |
| Bonnet cannot be secured in the closed position |8.4.1| | 1 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Fuel pipe union leaking |7.2.3| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Central Front Fuel pipe leaking excessively or a risk of fire pipes from fuel pump rotted |6.1.3 |b| |ii|| | 1 |
| Exhaust has a major leak of exhaust gases manifold blowing |6.1.2 |a|| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 1 |
| Offside Rear fog lamp missing |1.3.2a| | 1 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Nearside Front Track rod end loose |2.2.B.1d| | 1 |
| Offside Front Track rod end loose |2.2.B.1d| | 1 |
| Nearside Rear Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Nearside Windscreen wiper blade missing |8.2.2| | 1 |
| Offside Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Offside Front Direction indicator insecure |1.4.A.2b| | 1 |
| Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Offside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Headlamp not in a clean condition affecting beam image |1.2.4a| | 1 |
| Exhaust has a major leak of exhaust gases blowing at front pipe joint (6.1.2 (a)) | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Headlamp insecure (4.1.1 (c)) | 1 |
| Drivers seat backrest cannot be secured in the upright position. (6.2.5 (b) (ii)) | 1 |
| Nearside Headlamp insecure (4.1.1 (c)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Steering component casing retaining devices dangerously loose to shock absorber (2.1.2 (a) (ii)) | 1 |
| Front Service brake excessively fluctuating both sides (1.2.1 (e)) | 1 |
| Nearside Rear coil spring broken |2.4.C.1a| | 1 |
| Centre Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Front Front position lamp|s| not working also has water inside the lamp |1.1.A.3b| | 1 |
| Nearside Front Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings jacking point |6.1.B.2| | 1 |
| Offside Driver`s seat cannot be secured in the upright position. |6.2.A.2| | 1 |
| Nearside Front Outer Vehicle structure has excessive corrosion which adversely affects braking or steering jacking point |6.1.A.1| | 1 |
| Drivers door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
| Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt +has play (5.3.4 (b) (ii)) | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Headlamp aim not tested (4.1.2 (b)) | 1 |
| Offside Headlamp aim not tested (4.1.2 (b)) | 1 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Offside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Nearside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Nearside Front Body component damaged and likely to cause injury door handle |6.2.1 |a| |i|| | 1 |
| Offside Front Body component damaged and likely to cause injury door handle |6.2.1 |a| |i|| | 1 |
| Nearside Front Body component corroded and likely to cause injury |6.2.1 |a| |i|| | 1 |
| Fuel cap/sealing device ineffective |6.1.3 |b| |i|| | 1 |
| Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Exhaust system insecure |6.1.2 |a|| | 1 |
| Offside Rear Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
| Rear Brake valve has an excessive discharge of oil |3.6.E.1| | 1 |
| Nearside Front Direction indicator missing |1.4.A.2b| | 1 |
| Nearside Upper Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Rear Leaf spring has excessive wear in a shackle pin and/or bush |2.4.B.2| | 1 |
| Nearside Rear All position lamps not working |1.1.A.3b| | 1 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Rear Leaf spring has a deteriorated shackle pin rubber bush resulting in excessive movement |2.4.B.2| | 1 |
| Offside Front Upper Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Front Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Rear Position lamp not working |4.2.1 |a|| | 1 |
| Offside Front Position lamp not working |4.2.1 |a|| | 1 |
| Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded door shut |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded door shut |5.2.6| | 1 |
| Offside Rear Direction indicator adversely affected by the operation of another lamp (4.4.3 (b)) | 1 |
| Position lamp switch does not illuminate the front and rear position lamps with a single operation (4.2.2 (a)) | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Brake performance not tested (1.2.1 (g)) | 1 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced 3 areas marked (6.1.1 (c) (i)) | 1 |
| Offside Front Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Offside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Nearside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Nearside Rear Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Offside Rear Stop lamp not working |1.2.1b| | 1 |
| Fuel tank leaking |7.2.3| | 1 |
| Offside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Headlamp not working on dipped beam |1.7.5a| | 1 |
| Vehicle Identification Number not permanently displayed |6.3.5.a| | 1 |
| All position lamps not working |1.1.A.3b| | 1 |
| Offside Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Front Inner Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Direction indicators adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Nearside Front Exhaust system not adequately supported |7.1.1| | 1 |
| Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Front Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Rear coil spring cracked |2.4.C.1a| | 1 |
| Stop lamp not working ns |1.2.1b| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced under bonnet (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced underbonnet (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 1 |
| Nearside Inner Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Stop lamp(s) remains on when the brakes are released (4.3.2 (a) (iii)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Track rod end loose locknut not tight |2.2.B.1d| | 1 |
| Battery insecure behind radiator |1.9.1| | 1 |
| Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Front Track rod end ball joint worn to the extent there is a serious risk of detachment (2.1.3 (b) (ii)) | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Fuel hose so insecure there is a risk of fire (6.1.3 (a) (ii)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect cut off beam wrong side (4.1.2 (c)) | 1 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Offside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Nearside Front Direction indicators adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings in engine bay by engine monting |6.1.B.2| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded outer sill and chassis |5.2.6| | 1 |
| Front Exhaust system not adequately supported front clamp |7.1.1| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded front mount |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded rear mount |2.4.A.3| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing/chassis |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outrigger |6.1.B.2| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Rear Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Lower Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Nearside Front Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
| Offside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
| Nearside Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Brake pipe inadequately supported |3.6.B.1| | 1 |
| Nearside Rear Upper Rear position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Electrical wiring inadequately supported |1.9.2a| | 1 |
| Offside Headlamp does not operate immediately when selected on main beam |1.7.4a| | 1 |
| Offside Front Side repeater not working |1.4.A.2c| | 1 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Nearside Rear Leaf spring splayed and action impaired |2.4.B.1c| | 1 |
| Nearside Front Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Front passenger seat cannot be secured in the upright position. |6.2.4| | 1 |
| Nearside Front Windscreen wiper blade missing |8.2.2| | 1 |
| Stop lamp not working both |1.2.1b| | 1 |
| Offside Front Road wheel bead rim badly distorted |4.2.A.1a| | 1 |
| Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
| Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
| Nearside Side repeater incorrect colour |1.4.A.2f| | 1 |
| Headlamp insecure |1.7.3| | 1 |
| Offside Rear Leaf spring to axle securing bolt insecure |2.4.B.7b| | 1 |
| Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Front Ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Direction indicators not working |1.4.A.2c| | 1 |
| Nearside Passenger`s seat insecure |6.2.A.1| | 1 |
| Offside Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |
| Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Offside Front Front drive shaft coupling is insecure |2.5.C.1c| | 1 |
| Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 1 |
| Nearside Rear position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Seat belt anchorage prescribed area is excessively corroded Nearside front outer sill |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded offside front outer sill |5.2.6| | 1 |
| Seat belt anchorage prescribed area is excessively corroded nearside inner sill |5.2.6| | 1 |
| Suspension spring mounting prescribed area is excessively corroded nearside outer sill |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded nearside front inner wheel arch |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded offside front inner wheel arch |2.4.A.3| | 1 |
| Fuel cap/sealing device mounting flange/sealing method defective |7.2.4c| | 1 |
| Nearside Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Front Headlamp insecure |1.7.3| | 1 |
| Offside Front brake caliper leaking |3.6.A.1| | 1 |
| Brake performance not tested |3.7.A.1| | 1 |
| Offside Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Windscreen washer not working | 1 |
| Offside Rear Leaf spring anchor bracket corroded and seriously weakened (5.3.1 (b) (i)) | 1 |
| Nearside Rear Leaf spring anchor bracket corroded and seriously weakened (5.3.1 (b) (i)) | 1 |
| Offside Rear Inner Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength body (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength body (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Driver`s seat insecure o/s/f | mounting arear corodded |6.2.A.1| | 1 |
| Parking brake lever, pawl mechanism pivots or their associated mountings are insecure park brake lever insecure |attached to drivers seat which is insecure | |3.1.4b| | 1 |
| Exhaust system not adequately supported front exhAUSt join insecure |7.1.1| | 1 |
| Suspension component mounting prescribed area is excessively corroded o/s/f inner wing / susp tower area corodded |2.4.A.3| | 1 |
| Electrical wiring insecure |1.9.2a| | 1 |
| Offside Front Suspension component mounting prescribed area is severely distorted |2.4.A.3| | 1 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |