| Most common failures | No# failures |
|---|
| Registration plate lamp issues | 21 |
| Headlamp aim out of alignment | 18 |
| Windscreen wiper does not clear the windscreen effectively | 16 |
| Parking brake: efficiency below requirements |3.7.B.7| | 11 |
| Rear brake binding | 11 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
| Offside Rear fog lamp not working |1.3.2b| | 8 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 8 |
| Brake pipe excessively corroded | 8 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 7 |
| Exhaust system not adequately supported |7.1.1| | 6 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 6 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
| Rear parking brake recording little or no effort | 5 |
| Offside Headlamp insecure |1.7.3| | 5 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 5 |
| Horn not working |1.6.2a| | 5 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Registration plate issues | 5 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Offside Headlamp not working on main beam |1.7.5a| | 4 |
| Offside Steering rack gaiter split |2.2.D.2d| | 4 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 4 |
| Brakes imbalanced across an axle | 4 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 4 |
| Battery insecure |1.9.1| | 4 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 4 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 4 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 3 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Rear fog lamp tell tale not working |1.3.1b| | 3 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Nearside Rear Rear position lamp|s| insecure |1.1.A.3a| | 3 |
| Brake hose excessively deteriorated | 3 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 3 |
| Offside Front Headlamp insecure |1.7.3| | 3 |
| Driver`s seat insecure |6.2.A.1| | 3 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 3 |
| Offside Stop lamp not working |1.2.1b| | 2 |
| Nearside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
| Nearside Headlamp insecure |1.7.3| | 2 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Service brake: efficiency below requirements |3.7.B.7| | 2 |
| Hazard warning lamps inoperative |1.4.B.1b| | 2 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 2 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 2 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Direction indicator not working |1.4.A.2c| | 2 |
| Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 2 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Rear fog lamp not working |1.3.2b| | 2 |
| Offside Front brake disc excessively pitted |3.5.1h| | 2 |
| Centre Exhaust system not adequately supported |7.1.1| | 2 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 2 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 2 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 2 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 2 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Body has a sharp edge caused by corrosion wing |6.1.C.1| | 2 |
| Nearside Front Headlamp insecure |1.7.3| | 2 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Brake master cylinder fluid level below minimum level |3.6.G.1e| | 1 |
| Exhaust has a part missing |7.1.1a| | 1 |
| Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.B.1| | 1 |
| Centre Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Lower Electrical wiring insecure |1.9.2a| | 1 |
| Offside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Outer Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Front brake application uneven | 1 |
| Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Upper Suspension spring mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Nearside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Offside Headlamp not in a clean condition affecting beam image |1.2.4a| | 1 |
| Nearside Windscreen wiper blade missing |8.2.2| | 1 |
| Indicator tell tale inoperative |1.4.A.2a| | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Headlamp not working on dipped beam |1.7.5a| | 1 |
| Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
| Front Brake pipe leaking |3.6.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Outer Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Front Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Rear position lamp|s| insecure |1.1.A.3a| | 1 |
| Nearside Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
| Offside Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
| Nearside Rear An item not tested |Manual| | 1 |
| Offside Rear An item not tested |Manual| | 1 |
| Offside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| Nearside Stop lamp insecure |1.2.1a| | 1 |
| Nearside Rear Direction indicator insecure |1.4.A.2b| | 1 |
| Rear Exhaust mounting missing |7.1.1b| | 1 |
| Exhaust emits dense blue smoke at idle |7.3.A.2b| | 1 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Rear Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Centre Front Position lamp switch insecure |1.1.A.1| | 1 |
| Nearside Rear Lower Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Headlamp aim projected beam image is obviously incorrect Both (4.1.2 (c)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Front Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Service brake: efficiency below requirements |3.7.C.1a| | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Position lamp not working o/s front (4.2.1 (a) (ii)) | 1 |
| Headlamp aim projected beam image is obviously incorrect n/s (4.1.2 (c)) | 1 |
| Headlamp aim projected beam image is obviously incorrect o/s (4.1.2 (c)) | 1 |
| Exhaust system insecure mountings missing (6.1.2 (a)) | 1 |
| Suspension component mounting prescribed area excessively damaged significantly reducing structural strength n/s front inner wing (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced n/s front inner wing (7.1.1 (a) (i)) | 1 |
| Seat belt anchorage prescribed area strength or continuity significantly reduced n/s front step holed (7.1.1 (a) (i)) | 1 |
| Service brake excessively binding o/s rear (1.2.1 (f)) | 1 |
| Parking brake inoperative on one side n/s rear (1.4.1 (a)) | 1 |
| Parking brake inoperative on one side o/s rear (1.4.1 (a)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Offside Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Nearside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength strut mounting , (5.3.6 (a) (i)) | 1 |
| Front Electrical wiring inadequately supported |1.9.2a| | 1 |
| Nearside Rear Electrical wiring inadequately supported |1.9.2a| | 1 |
| Rear Electrical wiring inadequately supported |1.9.2a| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Front Passenger`s seat insecure |6.2.A.1| | 1 |
| Parking brake mechanism/associated mounting prescribed area is fractured |3.1.9| | 1 |
| Steering column movement between the shaft and steering wheel |2.1.2b| | 1 |
| Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings spring mounting |6.1.B.2| | 1 |
| Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings both outer sills |6.1.B.2| | 1 |
| Steering wheel locking device insecure |2.1.6| | 1 |
| Offside Rear Direction indicators not working |1.4.A.2c| | 1 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Front constant velocity joint is excessively worn |2.5.C.1b| | 1 |
| Direction indicators not working |1.4.A.2c| | 1 |
| Steering column top mounting bracket insecure |2.1.2d| | 1 |
| Front Electrical wiring inadequately supported OVER BATTERY |1.9.2a| | 1 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Nearside Front Statutory seat belt missing |5.1.1| | 1 |
| Offside Front Statutory seat belt missing |5.1.1| | 1 |
| Centre Rear Electrical wiring insecure |1.9.2a| | 1 |
| Nearside Front Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Position lamp switch faulty |1.1.A.1| | 1 |
| Headlamp switch faulty |1.7.1| | 1 |
| Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| rear brakes release unevenly |3.7.B.4| | 1 |
| Steering column top bearing excessively worn |2.1.2c| | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Stop lamp not working |1.2.1b| | 1 |
| Emissions not tested |7.0| | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Front Front drive shaft coupling flexible rubber or fabric coupling unit breaking up |2.5.C.1d| | 1 |
| Nearside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Front brake disc in such a condition that it is seriously weakened | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Rear lower arm chassis |2.4.A.3| | 1 |
| Nearside Rear Leaf spring shackle bracket corroded and seriously weakened |2.4.B.6d| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Inner wing |2.4.A.3| | 1 |
| Front Suspension component mounting prescribed area is excessively corroded Cross member |2.4.A.3| | 1 |
| Offside Rear Rear reflector excessively deteriorated so that its function is impaired Full of water |1.5.1c| | 1 |
| Rear Towbar component insecure |6.6.1| | 1 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Rear Leaf spring anchor bracket corroded and seriously weakened |2.4.B.6d| | 1 |
| Headlamp insecure |1.7.3| | 1 |
| Exhaust emits clearly visible black smoke during acceleration |7.3.A.2c| | 1 |
| Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Brake servo vacuum pipe deteriorated |3.6.C.1b| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Emissions not tested (8.2.1.2 (d)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch heavily corroded. top mount area (5.3.6 (a) (i)) | 1 |
| Nearside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt Insecure (6.1.7 (g) (ii)) | 1 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Body has a sharp edge caused by corrosion pillow |6.1.C.1| | 1 |
| Nearside Front Body has a sharp edge caused by corrosion wing bottom |6.1.C.1| | 1 |
| Nearside Front Upper Body has a sharp edge caused by damage wing |6.1.C.1| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion 1/4 panal |6.1.C.1| | 1 |
| Headlamp aim beam image obviously incorrect both front as bulbs insecure |1.8.A.1b| | 1 |
| Exhaust system not adequately supported tie wrapped |7.1.1| | 1 |
| Electrical wiring insecure under bonnet |1.9.2a| | 1 |
| Offside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Central Exhaust system insecure (6.1.2 (a)) | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Rear Bumper damaged and likely to cause injury when grazed or contacted (6.1.4 (a) (i)) | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced door step (7.1.1 (a) (i)) | 1 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Side repeater excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Offside Front Side repeater incomplete |1.5.A1b| | 1 |
| Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Offside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Fuel pipe leaking |7.2.3| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner arch |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength undersill |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength sill/panel |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength sill/panel |5.3.6 |a| |i|| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Upper Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings chassis |6.1.B.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded in wheel arch |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded in wheel arch |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded outrigger |2.4.A.3| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Nearside Outer Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced to horizontal member holed (6.1.1 (c) (i)) | 1 |
| Nearside Rear Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
| Offside Rear Position lamp light intensity significantly reduced (4.2.3 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength within suspension arm mounting point (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength within suspension arm mounting point (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Nearside Obligatory mirror not clearly visible from the drivers seat or incapable of being adjusted to be clearly visible from the driver`s seat |8.1.1d| | 1 |
| Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Vehicle structure has damage which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Rear Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Front Integral body structure is fractured and structural rigidity is significantly reduced out rigger |6.1.1 |a| |i|| | 1 |
| Offside Front Integral body structure is fractured and structural rigidity is significantly reduced out rigger |6.1.1 |a| |i|| | 1 |
| Offside Front Integral body structure is fractured and structural rigidity is significantly reduced footwell |6.1.1 |a| |i|| | 1 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Battery insecure and likely to fall from carrier |4.13 |a| |ii|| | 1 |
| Nearside Front Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Rear Upper Outline marker lamp not working |4.2.1 |a|| | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt split |2.1.3 |g| |ii|| | 1 |
| Offside Front Side repeater not working |1.4.A.2c| | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 1 |
| Rear Service brake excessively binding Both |1.2.1 |f|| | 1 |
| Nearside Rear Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Offside Front Driver`s seat moving inadvertently |6.2.5 |b| |ii|| | 1 |