Most common failures | No# failures |
---|
Registration plate issues | 6 |
Headlamp aim out of alignment | 5 |
Rear reflector on motorcycle missing |1.4.1| | 4 |
Rear reflector missing (4.8.2 (a) (ii)) | 4 |
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 2 |
Headlamp aim beam image kick up to the offside |1.6| | 2 |
Steering control handlebar movement restricted by trapped cables |2.1.2c| | 2 |
Stop lamp not working |4.3.1 |a| |ii|| | 2 |
Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 2 |
Stop lamp not working (4.3.1 (a) (ii)) | 2 |
Rear Position lamp not working (4.2.1 (a)) | 2 |
Registration plate lamp issues | 2 |
Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 2 |
Horn not working (7.7 (a) (ii)) | 2 |
Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 1 |
Direction indicators not working not fitted at time of test |1.5.1c| | 1 |
Headlamp dipped beam affected by the operation of another lamp |1.2.2c| | 1 |
Throttle operating incorrectly |6.2.1f| | 1 |
Rear reflector missing |4.8.2 |a| |ii|| | 1 |
Direction indicator flashing more than 120 times per minute |1.5.1c| | 1 |
Wheel alignment incorrect which adversely affects the handling |2.5.1| | 1 |
Steering headbearing has excessive free play |2.2.2| | 1 |
Nearside Front Stop lamp not working |4.3.1 |a| |ii|| | 1 |
Rear Stop lamp not working |4.3.1 |a| |ii|| | 1 |
Handlebar handgrip not secure to handlebars. |2.1.1c| | 1 |
Direction indicators not working |1.5.1c| | 1 |
Front Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Rear wheel bearings have excessive free play |2.4.A.2c| | 1 |
Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Front wheel bearings have excessive free play |2.3.5b| | 1 |
Front wheel bearings are excessively rough |2.3.5b| | 1 |
Offside Rear Direction indicator not working |1.5.1c| | 1 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Offside Front Direction indicators not working |1.5.1c| | 1 |
Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride chain split pin wrong way round |6.2.1h| | 1 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 1 |
Rear Roller brake test indicates a binding brake |3.3.A1a| | 1 |
Front position lamp does not illuminate immediately when switched on |1.1.3a| | 1 |
Rear Brake caliper|s| insecure |3.2.A1j| | 1 |
Exhaust has part of the system missing rear clamp |7.1.1a| | 1 |
Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
Front shock absorber seal failed and leaking oil both side front fork seal leaking |2.3.3| | 1 |
Throttle has a significant change in engine speed whilst moving the steering from lock to lock |2.1.4| | 1 |
Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
Front suspension fouling which affects the movement of the front suspension. mud guard. |2.3.6a| | 1 |
Chain guard insecure |6.2.1c| | 1 |
Rear Roller brake test indicates a sticking brake |3.3.A1a| | 1 |
Fuel system component leaking |7.2.1a| | 1 |
Rear Rear suspension bush has excessive free play |2.4.A2a|i|| | 1 |
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Headlamp light intensity severely reduced |4.1.4 |a|| | 1 |
Steering operation fouling on the fuel tank or bodywork on full lock |2.1.4 |b|| | 1 |
Front Wheel bearing play so excessive it is likely to break up |5.1.3 |a| |ii|| | 1 |
All direction indicators not working |4.4.1 |a| |ii|| | 1 |
Horn not working |7.7 |a| |ii|| | 1 |
Headlamp aim not tested |4.1.2 |b|| | 1 |
Rear Position lamp not working |4.2.1 |a|| | 1 |
Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
Rear Brake indicates excessive fluctuation of brake effort |1.2.1 |e|| | 1 |
Rear Shock absorber has a serious fluid leak |5.3.2 |b|| | 1 |
Rear Shock absorber has negligible damping effect |5.3.2 |b|| | 1 |
Nearside Front Shock absorber has a serious fluid leak |5.3.2 |b|| | 1 |
Front Wheel bearing so rough it is likely to overheat or break up |5.1.3 |b| |ii|| | 1 |
Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
Front Fuel system component leaking |6.1.3 |b| |i|| | 1 |
Roller brake test The less effective brake control does not achieve an efficiency of 25% |1.2.2 |a| |i|| | 1 |
Brake pedal is positioned so that the brake cannot be readily applied too high |1.1.2 |d|| | 1 |
Brake pedal anti-slip provision missing |1.1.2 |c|| | 1 |
Exhaust silencer likely to become detached nut missing off rear bolt |8.1.1 |b| |ii|| | 1 |
Nearside Front Direction indicator not working |4.4.1 |a| |ii|| | 1 |
Nearside Front Suspension component likely to fail leaking from bottom of leg |5.3.3 |b| |ii|| | 1 |
Front Position lamp missing |4.2.1 |a|| | 1 |
Headlamp aim so that beam "kick up" is not visible on the screen (4.1.2 (a)) | 1 |
Front Position lamp not working (4.2.1 (a)) | 1 |
Front Brake lever insecure (1.1.2 (e) (i)) | 1 |
Steering headbearing excessively stiff or notchy (2.2.2 (f) (i)) | 1 |
Nearside Rear All direction indicators adversely affected by the operation of another lamp (4.4.3 (b)) | 1 |
Offside Rear Direction indicator likely to become detached (4.4.1 (c) (ii)) | 1 |
Drive chain horseshoe locking device likely to become detached (6.1.7 (j) (ii)) | 1 |
Steering operation linkage fouling when handlebars turned from lock to lock (2.1.4 (a)) | 1 |
Central Front Upper Brake hose connection leaking (1.1.12 (c)) | 1 |
Rear Brake caliper leaking and braking performance affected (1.1.16 (b) (ii)) | 1 |
Rear Brake caliper insecure (1.1.16 (c) (i)) | 1 |
Wheel alignment incorrect which adversely affects the steering (2.4 (a)) | 1 |
Rear Exhaust system insecure (6.1.2 (a)) | 1 |
Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Nearside Front Shock absorber has a serious fluid leak (5.3.2 (b)) | 1 |
Riders seat insecure (6.2.5 (a) (ii)) | 1 |
Vehicle identification number not displayed (0.2 (a)) | 1 |
Clutch lever bent so it cannot be readily operated (6.2.7 (b)) | 1 |
Wheel more than one fixing missing (5.2.1 (a) (ii)) | 1 |
Brake pedal is so short that the brake cannot be readily applied (1.1.2 (d)) | 1 |
Roller brake test The less effective brake control does not achieve an efficiency of 25% (1.2.2 (a) (i)) | 1 |
Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Rear Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
Rear Brake indicates excessive fluctuation of brake effort (1.2.1 (e)) | 1 |
Drive chain excessively tight (6.1.7 (k) (i)) | 1 |
Motorcycle structure joining/attachment plate or fastening insecure Rear brake torque arm (6.1.1 (b) (i)) | 1 |
Headlamp aim projected beam image obviously incorrect dipping to the right (4.1.2 (c)) | 1 |
All direction indicators not working (4.4.1 (a) (ii)) | 1 |
Rear Rear reflector missing (4.8.2 (a) (ii)) | 1 |