Most common failures | No# failures |
---|
Headlamp aim out of alignment | 5 |
Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 3 |
Front Indicator switch inoperative Hazard light switch fails to operate indicators. |4.4.2 |a| |ii|| | 2 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 2 |
Rear Indicator switch inoperative Hazard light switch fails to operate indicators. |4.4.2 |a| |ii|| | 2 |
Front Brake fluid significantly below minimum mark |1.1.10 |d| |ii|| | 2 |
Registration plate issues | 2 |
Rear Road spring corroded so that its cross sectional area is reduced and seriously weakened |5.3.1 |b| |i|| | 2 |
Front Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 2 |
Headlamp aim beam image kick up to the offside |1.6| | 2 |
Floor brake test The less effective brake control does not achieve an efficiency of 25% |1.2.2 |a| |i|| | 1 |
Front Position lamp missing Front sidelight inop. |4.2.1 |a|| | 1 |
Rear Exhaust has a major leak of exhaust gases Excess smoke |black| from exhaust. |6.1.2 |a|| | 1 |
Front Brake caliper inadequately mounted Front caliper loose. |1.1.16 |c| |i|| | 1 |
Rear Motorcycle structure has excessive corrosion which adversely affects braking or steering Rear swingarm has excess corrosion and is holed. |6.1.1 |c| |ii|| | 1 |
Front Motorcycle structure insecure and likely to affect the correct functioning of the steering or braking |6.1.1c| | 1 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Rear Roller brake test indicates a sticking brake |3.3.A1a| | 1 |
Rear Brake pedal cannot be released smoothly |3.1.3d| | 1 |
Front Front suspension assembly excessive wear or free play in a front suspension component |2.3.4| | 1 |
Rear Floor brake test indicates a binding brake |3.3.C2c| | 1 |
Front Floor brake test indicates a sticking brake |3.3.C2c| | 1 |
Front Brake component defective due to a deliberate modification which significantly reduces the original strength |3.1.5| | 1 |
Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Front Brake grabbing severely |1.2.1 |c|| | 1 |
Front Position lamp not working |4.2.1 |a|| | 1 |
Rear Motorcycle structure corroded to the extent that the rigidity of the assembly is significantly reduced Rear swingarm has excessive corrosion and poor repair, new swingarm required. |6.1.1 |c| |i|| | 1 |
Front Fuel tank insecure |6.1.3 |a| |i|| | 1 |
Rear reflector missing (4.8.2 (a) (ii)) | 1 |
Front Steering movement excessively `notchy` with the wheel raised |2.2.1b| | 1 |
Front Brake disc|s| excessively scored |3.2.A1l| | 1 |
Rear Motorcycle structure joining/attachment plate or fastening insecure (6.1.1 (b) (i)) | 1 |
Rear Stop lamp not working (4.3.1 (a) (ii)) | 1 |
Offside Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Front Brake disc|s| friction surface contaminated by oil or grease |3.2.A1k| | 1 |
Brake lever is damaged and the brake cannot be readily applied |3.1.3c| | 1 |
Handlebar deformed |2.1.1b| | 1 |
Front position lamp does not illuminate immediately when switched on |1.1.3a| | 1 |
Front Roller brake test indicates a severely grabbing brake |3.3.A1b| | 1 |