| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 28 |
| Drive chain excessively loose |6.2.1d| | 25 |
| Rear Stop lamp remains on when the brake is released |1.3.1e| | 24 |
| Stop lamp remains on when the brakes are released | 14 |
| Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 12 |
| Stop lamp remains on when the brake is released |1.3.1e| | 12 |
| Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 11 |
| Drive chain worn to excess |6.2.1e| | 11 |
| Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 11 |
| Front Roller brake test indicates a binding brake |3.3.A1a| | 10 |
| Front wheel bearings have excessive free play |2.3.5b| | 9 |
| Registration plate issues | 9 |
| Rear Drive chain sprocket worn to excess |6.2.1e| | 8 |
| Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 7 |
| Front Stop lamp not working (4.3.1 (a) (ii)) | 7 |
| Drive chain sprocket carrier worn to excess |6.2.1e| | 5 |
| Rear Roller brake test indicates a binding brake |3.3.A1a| | 5 |
| Front Stop lamp remains on when the brake is released |1.3.1e| | 5 |
| Nearside Front Shock absorber has a serious fluid leak (5.3.2 (b)) | 4 |
| Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 4 |
| Drive chain excessively loose (6.1.7 (c) (i)) | 4 |
| Front Floor brake test indicates a binding brake |3.3.C2c| | 4 |
| Drive chain worn to excess (6.1.7 (c) (i)) | 3 |
| Front Drive chain sprocket worn to excess |6.2.1e| | 3 |
| Registration plate lamp issues | 3 |
| Rear Brake excessively binding (1.2.1 (f)) | 3 |
| Steering movement excessively `notchy` with the wheel raised |2.2.1b| | 3 |
| Nearside Front Direction indicators not working |1.5.1c| | 3 |
| Horn not working |1.7.3a| | 3 |
| Handlebar deformed |2.1.1b| | 3 |
| Front wheel bearings are excessively rough |2.3.5b| | 3 |
| Rear Drive chain sprocket carrier worn to excess |6.2.1e| | 2 |
| Brake lever cannot be released smoothly |3.1.3d| | 2 |
| Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 2 |
| Offside Front Shock absorber has a serious fluid leak (5.3.2 (b)) | 2 |
| Drive chain so loose it is likely to fail (6.1.7 (c) (ii)) | 2 |
| Nearside Handlebar grip insecure to handlebar (2.2.1 (d) (ii)) | 2 |
| Steering headbearing excessively stiff or notchy (2.2.2 (f) (i)) | 2 |
| Rear Stop lamp not working (4.3.1 (a) (ii)) | 2 |
| Drive chain excessively tight |6.2.1d| | 2 |
| Front Brake excessively binding (1.2.1 (f)) | 2 |
| Wheel alignment incorrect which adversely affects the steering (2.4 (a)) | 2 |
| Rear Roller brake test indicates a severely grabbing brake |3.3.A1b| | 2 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Rear Brake lining|s| less than 1.5 mm thick |3.2.A1f|i|| | 2 |
| Front Hydraulic brake control feels spongy |3.1.4a| | 2 |
| Nearside Handlebar handgrip not secure to handlebars. |2.1.1c| | 2 |
| Stop lamp not working |4.3.1 |a| |ii|| | 2 |
| Drive chain excessively loose |6.1.7 |c| |i|| | 2 |
| Direction indicators not working |1.5.1c| | 2 |
| Offside Handlebar handgrip not secure to handlebars. |2.1.1c| | 2 |
| Nearside Front shock absorber seal failed and leaking oil |2.3.3| | 2 |
| Rear Brake pedal cannot be released smoothly |3.1.3d| | 2 |
| Wheel alignment incorrect which adversely affects the handling |2.5.1| | 2 |
| Front Brake lever not releasing correctly and functionality of brakes affected (1.1.2 (b) (ii)) | 1 |
| Front Steering movement excessively `notchy` with the wheel raised |2.2.1b| | 1 |
| Nearside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
| Rear Stop lamp not working brake applied (4.3.1 (a) (ii)) | 1 |
| Wheel alignment incorrect which adversely affects the handling (2.4 (a)) | 1 |
| Handlebar deformed to the extent that steering is affected (2.2.1 (c) (ii)) | 1 |
| Front Handlebar excessively deformed bent |2.2.1 |c| |i|| | 1 |
| Handlebar grip insecure to handlebar bar end lose and bent |2.2.1 |d| |ii|| | 1 |
| Nearside Rear Direction indicators flashing more than 120 times per minute |1.5.1c| | 1 |
| Drive chain sprocket worn to excess |6.2.1e| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar motorcycle fitted with a standard silencer in average condition (8.1.1 (a)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Rear Exhaust noise is clearly in excess of that emitted by a similar motorcycle fitted with a standard silencer in average condition |8.1.1 |a|| | 1 |
| Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Nearside Rear Drive chain excessively loose |6.2.1d| | 1 |
| Nearside Rear Drive chain worn to excess |6.2.1e| | 1 |
| Nearside Rear Drive chain sprocket carrier worn to excess |6.2.1e| | 1 |
| Front Stop lamp does not emit a steady light |1.3.1b| | 1 |
| Indicator switch defective |1.5.4| | 1 |
| Rear Direction indicator not working Both (4.4.1 (a) (ii)) | 1 |
| Offside Front Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii)) | 1 |
| Rear Rear wheel spindle securing nut locking device missing |2.4.A.2b| | 1 |
| Rear Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
| Rear Stop lamp with a multiple light source more than 1/2 not functioning |4.3.1 |a| |ii|| | 1 |
| Front Wheel bearing so rough it is likely to overheat or break up |5.1.3 |b| |ii|| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar motorcycle fitted with a standard silencer in average condition |8.1.1 |a|| | 1 |
| Brake locking device missing Rear brake stable bar split pin missing |3.2.A1e| | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Front Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
| Rear wheel bearings have excessive free play |2.4.A.2c| | 1 |
| Rear reflector on motorcycle missing |1.4.1| | 1 |
| Nearside Direction indicators not working |1.5.1c| | 1 |
| Nearside Rear Direction indicators not working |1.5.1c| | 1 |
| Offside Front Brake lever cannot be applied smoothly |3.1.3d| | 1 |
| Offside Front Stop lamp remains on when the brake is released |1.3.1e| | 1 |
| Rear position lamp adversely affected by the operation of another lamp |1.1.3b| | 1 |
| Horn control defective |1.7.2a| | 1 |
| Handlebar mounting clamp bolt loose |2.1.1a| | 1 |
| Offside Rear Lower Stop lamp does not illuminate by the operation of both brake controls rear brake light not illuminating, cable to switch stretched - tightened to operate correctly (4.3.2 (a) (iii)) | 1 |
| Front Position lamp not working |4.2.1 |a|| | 1 |
| Brake pedal is positioned so that the brake cannot be readily applied missing stop adjuster |1.1.2 |d|| | 1 |
| Rear Wheel hub excessively worn (5.2.1 (b) (i)) | 1 |
| Offside Direction indicator not working |1.5.1c| | 1 |
| Offside Front Direction indicator not working |1.5.1c| | 1 |
| Front Brake fluid significantly below minimum mark |1.1.10 |d| |ii|| | 1 |
| Brake pedal is inoperative |3.1.3c| | 1 |
| Offside Front Direction indicator insecure |1.5.3b| | 1 |
| Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 1 |
| Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
| Front Motorcycle structure excessively corroded |6.1.1a| | 1 |
| Front Forks in such a condition that steering control is adversely affected (2.2.2 (d) (ii)) | 1 |
| Front Forks insecure (2.2.2 (d) (i)) | 1 |
| Steering movement excessively `notchy` with the weight on the lower bearing |2.2.1a| | 1 |
| Brake lever has inadequate reserve travel |3.1.3b| | 1 |
| Front Brake master cylinder severely damaged |3.2.B1b| | 1 |
| Roller brake test indicates a binding brake |3.3.A1a| | 1 |
| Rear Brake pedal pivots excessively worn |3.1.3a| | 1 |
| Front Brake fluid contaminated (1.8 (a)) | 1 |
| Centre Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
| Rear reflector on motorcycle dirty and function impaired |1.4.2a| | 1 |
| Roller brake test indicates a sticking brake |3.3.A1a| | 1 |
| Rear Brake pedal has inadequate reserve travel Needs adjusting. |3.1.3b| | 1 |
| Rear Brake locking device missing |3.2.A1e| | 1 |
| Rear wheel spindle securing nut locking device missing |2.4.A.2b| | 1 |
| Rear Stop lamp not working not working on rear brake (4.3.1 (a) (ii)) | 1 |
| Stop lamp does not illuminate immediately a brake applies rear brake lever |1.3.1a| | 1 |
| Rear reflector missing (4.8.2 (a) (ii)) | 1 |
| Rear All direction indicators incorrect colour R/H (4.4.3 (a)) | 1 |
| Front Brake grabbing severely (1.2.1 (c)) | 1 |
| Offside Rear Drive chain sprocket carrier worn to excess rubbers worn |6.2.1e| | 1 |
| Nearside Rear Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride spit pin fitted wrong way around |6.2.1h| | 1 |
| Offside Rear Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
| Offside Rear Exhaust noise is clearly in excess of that emitted by a similar motor bicycle fitted with a standard silencer in average condition |7.1.2| | 1 |
| Front Headlamp aim so that beam "kick up" is not visible on the screen |1.6.B.1| | 1 |
| Front Front position lamp deteriorated and function impaired can,t see light on head lamp screen |1.1.1b| | 1 |
| Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Front Brake fluid reservoir fluid level significantly below minimum level (1.1.10 (d) (ii)) | 1 |
| Brake pedal cannot be released smoothly |3.1.3d| | 1 |
| Front Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 1 |
| Drive chain sprocket carrier worn to excess cush drive rubber |6.2.1e| | 1 |
| Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
| Rear Floor brake test indicates a sticking brake |3.3.C2c| | 1 |
| Rear Position lamp not working (4.2.1 (a)) | 1 |
| Rear Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii)) | 1 |
| Rear Brake cable has restricted free movement (1.1.15 (e)) | 1 |
| Rear Drive chain sprocket so worn it is likely to fail (6.1.7 (c) (ii)) | 1 |
| Rear Exhaust system insecure rear fixing bolt is snapped off (6.1.2 (a)) | 1 |
| Offside Rear Direction indicator insecure |1.5.3b| | 1 |
| Front Brake disc|s| friction surface contaminated by oil or grease |3.2.A1k| | 1 |
| Stop lamp does not illuminate immediately a brake applies not working |1.3.1a| | 1 |
| Rear position lamp does not illuminate immediately when it is switched on not working |1.1.3a| | 1 |
| Rear Brake indicates excessive fluctuation of brake effort (1.2.1 (e)) | 1 |
| Front Brake hose fouling |3.2.B3b| | 1 |
| Direction indicator damaged and function impaired |1.5.3a| | 1 |
| Rear Roller brake test indicates a sticking brake |3.3.A1a| | 1 |
| Exhaust system insecure |6.1.2 |a|| | 1 |
| Offside Front Direction indicator deteriorated and function impaired |1.5.3a| | 1 |
| Steering headbearing has excessive free play |2.2.2| | 1 |
| Horn not working |7.7 |a| |ii|| | 1 |
| Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
| Headlamp aim not tested |1.6| | 1 |
| Front position lamp does not illuminate immediately when switched on |1.1.3a| | 1 |
| Direction indicators flashing more than 120 times per minute |1.5.1c| | 1 |
| Nearside Front Direction indicator not working |1.5.1c| | 1 |
| Drive chain fouling another component |6.2.1d| | 1 |
| Rear Drive chain sprocket worn to excess (6.1.7 (c) (i)) | 1 |
| Rear Stop lamp remains on when the brake is released foot control |1.3.1e| | 1 |
| Nearside Front Handlebar mounting clamp bolt loose |2.1.1a| | 1 |
| Offside Front Handlebar mounting clamp bolt loose |2.1.1a| | 1 |
| Stop lamp not working hand control 1 |4.3.1 |a| |ii|| | 1 |
| Stop lamp does not illuminate immediately a brake applies control one |1.3.1a| | 1 |
| Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) | 1 |
| Nearside Rear Direction indicator not working |1.5.1c| | 1 |
| Rear Brake disc significantly and obviously worn under minimum (1.1.14 (a) (i)) | 1 |
| Front Headlamp not working on main beam bulb replaced. (4.1.1 (a) (ii)) | 1 |