Most common failures | No# failures |
---|
Brake pipe excessively corroded | 291 |
Headlamp aim out of alignment | 111 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 100 |
Windscreen wiper does not clear the windscreen effectively | 91 |
Registration plate lamp issues | 82 |
Brake hose excessively deteriorated | 78 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 69 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 65 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 64 |
Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 54 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 38 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 35 |
Registration plate issues | 30 |
Brakes imbalanced across an axle | 25 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 24 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 24 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 23 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 22 |
Exhaust has a major leak of exhaust gases |7.1.2| | 22 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 21 |
Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 20 |
Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 20 |
Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 19 |
Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 18 |
Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 18 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 18 |
Rear brake binding | 18 |
Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 17 |
Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 17 |
Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 16 |
Offside Stop lamp not working |1.2.1b| | 16 |
Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 16 |
Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 16 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 15 |
Nearside Stop lamp not working |1.2.1b| | 15 |
Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 14 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 14 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 14 |
Offside Front coil spring fractured |2.4.C.1a| | 13 |
Horn not working |1.6.2a| | 12 |
Parking brake: efficiency below requirements |3.7.B.7| | 12 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
Emissions not tested |7.0| | 11 |
Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 10 |
Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
Offside Front position lamp|s| not working |1.1.A.3b| | 10 |
Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 10 |
Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 9 |
Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 9 |
Offside Front wheel bearing rough when rotated |2.5.A.2| | 9 |
Service brake: efficiency below requirements |3.7.B.7| | 9 |
Offside Windscreen wiper blade deteriorated |8.2.2| | 9 |
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 9 |
Nearside Windscreen wiper blade deteriorated |8.2.2| | 9 |
Nearside Front coil spring fractured |2.4.C.1a| | 8 |
Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 8 |
Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 8 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 8 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 8 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 8 |
Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 8 |
Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 8 |
Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 8 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 8 |
Offside Rear fog lamp not working |1.3.2b| | 8 |
Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 8 |
Front brake disc in such a condition that it is seriously weakened | 8 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 7 |
Nearside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 7 |
Offside Front Windscreen wiper blade deteriorated |8.2.2| | 7 |
Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 7 |
Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 7 |
Offside Front Direction indicator not working |1.4.A.2c| | 7 |
Brake hose damaged | 7 |
Windscreen has damage | 6 |
Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 6 |
Offside Rear Rear wheel bearing has excessive play |2.6.2| | 6 |
Offside Rear wheel bearing has excessive play |2.6.2| | 6 |
Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 6 |
Offside Rear Braking system leaking |3.6.A.1| | 6 |
Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Rear parking brake recording little or no effort | 6 |
Nearside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 6 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 6 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Offside Rear fog lamp insecure |1.3.2a| | 6 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 5 |
Nearside Front Anti-roll bar linkage insecure |2.4.G.1| | 5 |
Service brake: efficiency below requirements |3.7.C.1a| | 5 |
Parking brake: efficiency below requirements |3.7.C.1b| | 5 |
Offside Front coil spring incomplete |2.4.C.1a| | 5 |
Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 5 |
Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 5 |
Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 5 |
Offside Rear wheel bearing rough when rotated |2.6.1| | 5 |
Nearside Rear Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Offside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Windscreen wiper blade insecure | 5 |
Offside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Offside Rear Shock absorber has negligible damping effect |2.7.5| | 5 |
Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Rear Mechanical brake component has restricted free movement | 4 |
Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Nearside Front Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 4 |
Centre Rear Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
Nearside Front Direction indicator not working |1.4.A.2c| | 4 |
Nearside Front Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 4 |
Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 4 |
Offside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 4 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
Nearside Front Direction indicator incomplete |1.5.A1b| | 4 |
Offside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 4 |
Offside Rear Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Front brake application uneven | 4 |
Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.D.1| | 4 |
Offside Front Suspension arm corroded and seriously weakened |2.4.G.1| | 4 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
Nearside Front wheel bearing rough when rotated |2.5.A.2| | 4 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
Fuel cap/sealing device sealing washer missing |7.2.4c| | 4 |
Offside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 4 |
Offside Front brake disc excessively pitted |3.5.1h| | 4 |
Offside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 4 |
Nearside Front brake disc excessively pitted |3.5.1h| | 4 |
Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Nearside Headlamp insecure |1.7.3| | 4 |
Offside Rear Stop lamp not working |1.2.1b| | 4 |
Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 3 |
Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Nearside Rear wheel bearing has excessive play |2.6.2| | 3 |
Nearside Front constant velocity joint is excessively worn |2.5.C.1b| | 3 |
Nearside Outer Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 3 |
Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Rear Exhaust has a part missing |7.1.1a| | 3 |
Offside Front position lamp|s| insecure |1.1.A.3a| | 3 |
Offside Front Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 3 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 3 |
Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 3 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 3 |
Nearside Front coil spring incomplete |2.4.C.1a| | 3 |
Nearside Rear Upper Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 3 |
Nearside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 3 |
Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 3 |
Offside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Front Brake hose excessively damaged |3.6.B.4d| | 3 |
Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 3 |
Nearside Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 3 |
Front position lamp|s| not working |1.1.A.3b| | 3 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 3 |
Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 3 |
Offside front brake binding |3.7.B.1| | 3 |
Nearside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 3 |
Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 3 |
All position lamps not working |1.1.A.3b| | 3 |
Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 3 |
Offside Front Lower Suspension arm corroded and seriously weakened |2.4.G.1| | 3 |
Nearside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 3 |
Brake performance not tested |3.7.A.1| | 3 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 3 |
Offside Front wheel bearing has excessive play |2.5.A.3c| | 3 |
Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 3 |
Offside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Front Anti-roll bar linkage fractured |2.4.G.1| | 3 |
Nearside Rear wheel bearing rough when rotated |2.6.1| | 3 |
Brake cable has wires broken and is significantly weakened |3.5.1b| | 3 |
Offside Front Direction indicator incomplete |1.5.A1b| | 3 |
Fuel cap/sealing device missing |7.2.4a| | 3 |
Front Anti-roll bar missing |2.4.G.1| | 3 |
Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |