| Most common failures | No# failures |
|---|
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 25 |
| Headlamp aim out of alignment | 23 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 20 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 19 |
| Windscreen wiper does not clear the windscreen effectively | 19 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 17 |
| Brake pipe excessively corroded | 17 |
| Registration plate lamp issues | 14 |
| Brake hose excessively deteriorated | 13 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 11 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 11 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 11 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 10 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 10 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 10 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 9 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| Registration plate issues | 8 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 7 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 6 |
| Brakes imbalanced across an axle | 6 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
| Emissions not tested |7.0| | 6 |
| Nearside Stop lamp not working |1.2.1b| | 5 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 5 |
| Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 5 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 4 |
| Front brake application uneven | 4 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 4 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 4 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 4 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 4 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 4 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 4 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Rear brake binding | 4 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Offside Rear fog lamp not working |1.3.2b| | 3 |
| Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Rear Rear fog lamp not working |1.3.2b| | 3 |
| Service brake: efficiency below requirements |3.7.B.7| | 3 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 3 |
| Offside Front Direction indicator not working |1.4.A.2c| | 3 |
| Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 3 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 3 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 3 |
| Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 3 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 3 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 3 |
| Windscreen wiper blade insecure | 3 |
| Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 3 |
| Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 3 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 2 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 2 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 2 |
| Nearside Front Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Front Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Offside Front front brake binding |3.7.B.1| | 2 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 2 |
| All position lamps not working |1.1.A.3b| | 2 |
| Nearside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Stop lamp not working |1.2.1b| | 2 |
| Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Front Side repeater not working |1.4.A.2c| | 2 |
| Nearside Rear Shock absorber has negligible damping effect |2.7.5| | 2 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 2 |
| Brake performance not tested |3.7.A.1| | 2 |
| Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Nearside Front Lower Body has a projection caused by corrosion |6.1.C.1| | 2 |
| Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Offside Headlamp not working on main beam |1.7.5a| | 2 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Front Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Offside Rear Anti-roll bar fractured |2.4.G.1| | 1 |
| Nearside Side repeater incomplete |1.5.A1b| | 1 |
| Offside Front All position lamps not working |1.1.A.3b| | 1 |
| Offside Rear All position lamps not working |1.1.A.3b| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing within 30 cm of suspension top mount |6.1.B.2| | 1 |
| Nearside Front passenger seat cannot be secured in the upright position. |6.2.4| | 1 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Service brake: efficiency below requirements |3.7.C.1a| | 1 |
| Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear fog lamp insecure |1.3.2a| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Nearside Outer Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Fuel system component insecure |7.2.1| | 1 |
| Nearside Outer Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Nearside Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Front Anti-roll bar missing |2.4.G.1| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Offside Rear Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Nearside Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Nearside Front Valve stem seriously misaligned |4.1.D.1e| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Steering wheel in a condition that hampers proper control |2.1.1| | 1 |
| Centre Exhaust system not adequately supported |7.1.1| | 1 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.B.1| | 1 |
| Nearside Front coil spring incomplete |2.4.C.1a| | 1 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Brake valve leaking |3.6.A.1| | 1 |
| Nearside Front Anti-roll bar synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
| Nearside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Nearside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Lower Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Lower Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Lower Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Offside Front Lower Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Nearside Lower Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Nearside Rear Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Offside Rear Shock absorber detached |2.7.2b| | 1 |
| Nearside Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Nearside Front Steering locking device missing |2.2.C.1g| | 1 |
| Nearside Front Front suspension has a suspension lower ball joint securing nut not locked |2.5.B.1a| | 1 |
| Offside Front Braking system leaking |3.6.A.1| | 1 |
| Nearside Rear Torsion bar repaired by welding |2.4.E.1c| | 1 |
| Offside Front Lower Coil spring mounting corroded and seriously weakened |2.4.C.3c| | 1 |
| Offside Inner Rear Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Offside Inner Front Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Rear Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting damaged and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Rear Torque/reaction arm has a deteriorated rubber bush resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Suspension arm attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Rear Direction indicator flashing more than 120 times a minute |1.4.A.2g| | 1 |
| Offside Rear Direction indicator flashing more than 120 times a minute |1.4.A.2g| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Rear engine mounting deteriorated resulting in excessive movement |6.1.D.1a| | 1 |
| Front Exhaust system not adequately supported |7.1.1| | 1 |
| Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Offside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area is excessively corroded wheel arch |5.2.6| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded wheel arch |5.2.6| | 1 |
| Nearside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Road wheel bead rim badly distorted |4.2.A.1a| | 1 |
| Offside Headlamp aim beam image too far to the right |1.6.B4| | 1 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Front Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Shock absorber has negligible damping effect |2.7.5| | 1 |
| Nearside Front Suspension arm attachment bracket/mounting damaged and its strength is seriously reduced |2.4.G.1| | 1 |
| Fuel tank leaking |7.2.3| | 1 |
| Nearside Rear Torsion bar excessive play at an end fixing |2.4.E.2| | 1 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Front Headlamp insecure |1.7.3| | 1 |
| Offside Front Front constant velocity joint gaiter missing |2.5.C.1a| | 1 |
| Nearside Front Direction indicator incomplete |1.5.A1b| | 1 |
| Offside Front Macpherson strut has excessive movement at the upper attachment |2.5.A.1c| | 1 |
| Tailgate cannot be secured in the closed position |6.4.1| | 1 |
| Centre Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Front Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Rear Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 1 |
| Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Inner Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Outer Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Offside Front Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Rear Wheel nut|s| missing |4.2.A.1e| | 1 |
| Offside Front Wheel nut|s| missing |4.2.A.1e| | 1 |
| Offside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Nearside Rear Brake hose bulging under pressure |3.6.B.3| | 1 |
| Offside Front Lower Brake hose bulging under pressure |3.6.B.3| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front constant velocity joint is excessively worn |2.5.C.1b| | 1 |
| Nearside Rear Fuel system component insecure |7.2.1| | 1 |
| Offside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Nearside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Front Side repeater incomplete |1.5.A1b| | 1 |
| Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
| Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Windscreen has damage | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Front Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Side repeater not working |1.4.A.2c| | 1 |
| An item not tested |Manual| | 1 |
| Fuel cap/sealing device sealing washer missing |7.2.4c| | 1 |
| Offside Front Direction indicator incomplete |1.5.A1b| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Nearside Rear Suspension arm attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside front brakes release unevenly |3.7.B.4| | 1 |
| Nearside Rear Wheel stud|s| missing |4.2.A.1e| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |7.1.4| | 1 |
| Offside Front front brake juddering severely |3.7.A.2b| | 1 |
| Nearside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Offside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Offside Front position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Rear fog lamp does not face the rear |1.3.2a| | 1 |
| Front Anti-roll bar synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Rear Anti-roll bar has excessive play in a pin/bearing |2.4.G.2| | 1 |
| Front Trailing arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Nearside Front Sub-frame attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Nearside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Nearside Rear Vehicle structure is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Vehicle structure is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Vehicle structure is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
| Offside Rear Braking system leaking |3.6.A.1| | 1 |
| Brake pedal creeps down when held under pressure |3.3.B.1a| | 1 |
| Front passenger seat insecure |6.2.3| | 1 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |