| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 14 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| Headlamp aim out of alignment | 8 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 7 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 7 |
| Brakes imbalanced across an axle | 7 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 6 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Service brake: efficiency below requirements |3.7.B.7| | 5 |
| Windscreen wiper does not clear the windscreen effectively | 5 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Brake hose excessively deteriorated | 4 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Offside Rear fog lamp not working |1.3.2b| | 3 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Offside Front front brake binding |3.7.B.1| | 3 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 2 |
| Offside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Rear parking brake recording little or no effort | 2 |
| Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Horn not working |1.6.2a| | 2 |
| Front brake disc in such a condition that it is seriously weakened | 2 |
| Nearside Front brake caliper has restricted free movement |3.5.1k| | 2 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Tie bar/rod attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Nearside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Nearside Front Suspension arm attachment bracket/mounting nut missing |2.4.G.1| | 1 |
| Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Fuel system component leaking |7.2.3| | 1 |
| Offside Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Driver`s seat insecure |6.2.A.1| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Offside Outer Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Rear Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Centre Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Obligatory mirror missing |8.1.1| | 1 |
| Brake performance not tested |3.7.A.1| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| All position lamps not working |1.1.A.3b| | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front coil spring incomplete |2.4.C.1a| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Rear fog lamp insecure |1.3.2a| | 1 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Rear brake application uneven | 1 |
| rear brakes release unevenly |3.7.B.4| | 1 |
| Offside Front Seat belt affected by an insecure seat fixing |5.2.1b| | 1 |
| Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Front Headlamp not working on main beam |1.7.5a| | 1 |
| Front Headlamp not in good working order |not working| |1.2.4a| | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Nearside Body has a projection caused by damage |6.1.C.1| | 1 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Offside Front Position lamp not working |4.2.1 |a|| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Nearside Rear Trailing arm rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Trailing arm rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Bonnet retaining device ineffective |8.4.2| | 1 |
| Offside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Front Electrical wiring inadequately supported |1.9.2a| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front coil spring incomplete |2.4.C.1a| | 1 |
| Nearside Front Macpherson strut has excessive movement in the upper support bearing assembly |2.5.B.1b| | 1 |
| Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Front Windscreen wiper blade missing |8.2.2| | 1 |
| Offside Front Windscreen wiper blade missing |8.2.2| | 1 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
| Nearside Outer Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Outer Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Outer Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Rear Sub-frame has excessive play in a pin/bush |2.4.G.2| | 1 |
| Windscreen wiper blade insecure | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Rear Stub axle has excessive vertical movement between stub axle and axle beam |2.5.A.1a| | 1 |
| Nearside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Outer Rear Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Outer Rear Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Nearside front brake juddering severely |3.7.A.2b| | 1 |
| Offside front brake juddering severely |3.7.A.2b| | 1 |
| Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Nearside Front An item not tested |Manual| | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Rear Brake hose bulging under pressure |3.6.B.3| | 1 |
| Offside Rear Brake hose bulging under pressure |3.6.B.3| | 1 |
| Registration plate issues | 1 |
| Nearside Fuel tank leaking |7.2.3| | 1 |
| Offside Front brake caliper has restricted free movement |3.5.1k| | 1 |
| Headlamp aim projected beam image is obviously incorrect n/s and o/s |4.1.2 |c|| | 1 |
| Nearside Front Position lamp not working |4.2.1 |a|| | 1 |
| Front Anti-roll bar pin or bush excessively worn n/s and o/s |rear| bushes |5.3.4 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 1 |