| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 62 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 42 |
| Registration plate lamp issues | 22 |
| Windscreen wiper does not clear the windscreen effectively | 22 |
| Brakes imbalanced across an axle | 19 |
| Service brake: efficiency below requirements |3.7.B.7| | 18 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 17 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 17 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 14 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 13 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 12 |
| Rear parking brake recording little or no effort | 12 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 10 |
| Parking brake: efficiency below requirements |3.7.B.7| | 10 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
| Offside Steering rack gaiter split |2.2.D.2d| | 10 |
| Rear brake application uneven | 8 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 7 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 7 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 7 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 6 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 6 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 6 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 5 |
| Centre Exhaust system not adequately supported |7.1.1| | 5 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Battery insecure |1.9.1| | 5 |
| Windscreen washer not working | 5 |
| Registration plate issues | 4 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 4 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 4 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 4 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 4 |
| Brake pipe excessively corroded | 4 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 4 |
| Nearside Stop lamp not working |1.2.1b| | 4 |
| Offside Stop lamp not working |1.2.1b| | 4 |
| Horn not working |1.6.2a| | 4 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 4 |
| Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 3 |
| Nearside Inner Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Steering rack gaiter insecure |2.2.D.2d| | 3 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Rear fog lamp tell tale not working |1.3.1b| | 3 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 3 |
| Brake hose excessively deteriorated | 3 |
| Rear brake binding | 3 |
| Offside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Offside Side repeater not working |1.4.A.2c| | 3 |
| Exhaust emissions carbon monoxide content excessive |8.2.1.2 |b|| | 3 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 3 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 3 |
| Offside Headlamp insecure |1.7.3| | 3 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 3 |
| Offside Rear fog lamp not working |1.3.2b| | 3 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Hazard warning switch faulty |1.4.B.1d| | 3 |
| Rear Exhaust system not adequately supported |7.1.1| | 3 |
| Offside Rear Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 3 |
| Rear fog lamp not working |1.3.2b| | 3 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 3 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 3 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 3 |
| Offside Front Headlamp insecure |1.7.3| | 2 |
| rear brakes release unevenly |3.7.B.4| | 2 |
| Exhaust mounting missing |7.1.1b| | 2 |
| Offside Front Shock absorber has an excessively worn bush |2.7.4| | 2 |
| Nearside Rear Radius arm has excessive play in a pin/bush |2.4.G.2| | 2 |
| Parking brake lever has no reserve travel |3.1.6b| | 2 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Outer Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Headlamp insecure |1.7.3| | 2 |
| Front Direction indicators not working |1.4.A.2c| | 2 |
| Rear Direction indicators not working |1.4.A.2c| | 2 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Side repeater not working |1.4.A.2c| | 2 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 2 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Fluid suspension has no suspension movement |2.4.D.5| | 2 |
| Emissions not tested |7.0| | 2 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Offside Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 2 |
| Nearside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Nearside Front Lower Shock absorber has an excessively worn bush |2.7.4| | 2 |
| Nearside Steering arm has relative movement at its fixings |2.2.B.1h| | 2 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
| Nearside Headlamp not working on main beam |1.7.5a| | 2 |
| Nearside Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 2 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Rear Stop lamp not working |1.2.1b| | 2 |
| Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Offside Rear Sub-frame rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Nearside Side repeater insecure |1.4.A.2b| | 2 |
| Hazard warning lamps inoperative |1.4.B.1b| | 2 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 2 |
| Front passenger seat insecure |6.2.3| | 2 |
| Nearside Front Steering rack damaged and unserviceable |2.2.C.1d| | 1 |
| Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Rear Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
| Offside Front Direction indicator not working |4.4.1 |a| |ii|| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Offside Headlamp aim so that beam "kick up" is not visible on the screen no patten |4.1.2 |a|| | 1 |
| Passenger`s seat insecure |6.2.6 |a| |ii|| | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn traling arm |5.3.4 |a| |i|| | 1 |
| Service brake efficiency less than 50% of the required value |1.2.2 |a| |ii|| | 1 |
| Rear Fluid suspension unit supply pipe corroded and seriously weakened |2.4.D.3| | 1 |
| Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Headlamps matched pair are incorrectly positioned |1.7.3| | 1 |
| Centre Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Centre Rear Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Position lamp switch faulty |1.1.A.1| | 1 |
| Nearside Outer Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Centre Exhaust mounting missing |7.1.1b| | 1 |
| Direction indicators not in good working order |function impaired| |1.5.A1b| | 1 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Front Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Braking system leaking possible caliper bleed nipple? |3.6.A.1| | 1 |
| Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Wheel insecure |4.2.A.1c| | 1 |
| Nearside Rear Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Radius arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Centre Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Front Steering rack fractured and unserviceable |2.2.C.1d| | 1 |
| Offside front brake juddering severely |3.7.A.2b| | 1 |
| Nearside Rear Fluid suspension unit totally deflated |2.4.D.1a| | 1 |
| Offside Rear Fluid suspension unit totally deflated |2.4.D.1a| | 1 |
| Rear Stop lamp not working |1.2.1b| | 1 |
| Offside Front Upper Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Body has a projection caused by damage |6.1.C.1| | 1 |
| Nearside Rear Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Outer Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Cross member |5.3.6 |a| |ii|| | 1 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.B.1| | 1 |
| Front Steering rack deformed and unserviceable |2.2.C.1d| | 1 |
| Offside Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
| Nearside Rear Suspension arm has excessive play in a pin/bearing |2.4.G.2| | 1 |
| Offside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Battery insecure (1.9.1) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Offside rear brake recording little or no effort (3.7.B.5a) | 1 |
| Nearside Steering rack gaiter split (2.2.D.2d) | 1 |
| Offside Rear rear brake recording little or no effort (3.7.B.5a) | 1 |
| Offside Front Steering rack gaiter split (2.2.D.2d) | 1 |
| Exhaust emissions carbon monoxide content excessive (7.3.B.1a) | 1 |
| Exhaust emissions hydrocarbon content excessive (7.3.B.1b) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front cross member corroded in various places (5.3.6 (a) (i)) | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Steering system excessively rough |2.2.D.1| | 1 |
| Nearside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Rear rear brake grabbing severely |3.7.A.5b| | 1 |
| Nearside Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside front brake recording little or no effort |3.7.B.5a| | 1 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
| Front brake application uneven | 1 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Front Upper Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
| Stop lamp remains on when the brakes are released | 1 |
| Fuel cap/sealing device mounting flange/sealing method defective |7.2.4c| | 1 |
| Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
| Nearside Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Rear Vehicle structure is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| Centre Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| Nearside Front Side repeater not working |1.4.A.2c| | 1 |
| Offside Front Steering column deformed and unserviceable |2.2.C.1d| | 1 |
| Anti-roll bar linkage pin or bush likely to become detached n/s split pin missing |5.3.4 |a| |ii|| | 1 |
| Nearside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area so inadequately repaired that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
| Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
| Rear Sub-frame corroded and seriously weakened |5.3.3 |b| |i|| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Front Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Brake pedal anti-slip provision incomplete |3.3.A.1b| | 1 |
| Offside Obligatory mirror missing |8.1.1| | 1 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 1 |
| Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Rear Sub-frame rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment |1.1.6 |c|| | 1 |
| Oil leaking excessively from engine |8.4.1 |a| |i|| | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced A post |6.1.1 |c| |i|| | 1 |
| Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shock mount |5.3.6 |a| |i|| | 1 |
| Central Exhaust system insecure |6.1.2 |a|| | 1 |
| Steering rack has excessive free play detected at the steering wheel |steering rack fitted| |2.3 |a| |i|| | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded inner and outer sill |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Nearside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded flitch |2.4.A.3| | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded flitch by bulkhead |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded b pillar |5.2.6| | 1 |
| Offside Rear Outer Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Outer Subframe mounting prescribed area is excessively corroded arch |2.4.A.3| | 1 |
| Offside Rear Inner Subframe mounting prescribed area is excessively corroded arch at front |2.4.A.3| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor-total of 8 separate holes in floor |5.2.6| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded jacking point |2.4.A.3| | 1 |
| Offside Rear Inner Subframe mounting prescribed area is excessively corroded sill-by fuel tank |2.4.A.3| | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded arch |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded a pillar |2.4.A.3| | 1 |
| Nearside Front Sub-frame attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Nearside Rear Steering rack gaiter split |2.2.D.2d| | 1 |
| Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Rear Stop lamp not working both |1.2.1b| | 1 |
| Front Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Offside Track rod end ball pin shank loose |2.2.B.1c| | 1 |
| Offside Front Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Rear Sub-frame rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 1 |
| Offside Front Subframe mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Nearside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 1 |
| Nearside Front Bumper damaged and likely to cause injury when grazed or contacted and rear end caps missing |6.1.4 |a| |i|| | 1 |
| Front Bonnet primary retaining device ineffective missing |3.1 |c|| | 1 |
| Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Nearside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Nearside Front Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
| Rear Fluid suspension supply pipe insecure |2.4.D.3| | 1 |
| Rear Fluid suspension unit fouled by moving parts likely to cause damage |2.4.D.1c| | 1 |
| Nearside Rear Direction indicator flashing less than 60 times a minute |1.4.A.2g| | 1 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Offside Rear Sub-frame attachment rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Inner Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Body has a projection caused by damage |6.1.C.1| | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength front cross member (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Rear Sub-frame corroded and seriously weakened Axle Beam welded repairs (5.3.3 (b) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor by jacking point (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Floor by jacking point (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Brake pedal anti-slip provision missing |3.3.A.1b| | 1 |
| Nearside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
| Nearside Direction indicators adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Offside Front Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Rear Axle swivel joint has excessive play |2.5.A.3b| | 1 |
| Offside Front Drivers seat with a defective structure (6.2.5 (a) (i)) | 1 |
| Nearside Front Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded cross member corroded visable from under bonner |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded floor pan area |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded jacking point |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Nearside Outer Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Passenger`s seat insecure |6.2.A.1| | 1 |
| Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Outer Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Sub-frame attachment rubber mounting bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Front Bonnet cannot be secured in the closed position |8.4.1| | 1 |
| Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front Direction indicator incomplete |1.5.A1b| | 1 |
| Offside Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Front position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Front position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Outer Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Bonded suspension unit attachment fractured |2.4.F.1b| | 1 |
| Nearside Track rod end loose |2.2.B.1d| | 1 |
| Steering component cracked and unserviceable |2.2.C.1d| | 1 |
| Rear Fluid suspension unit interconnecting pipe corroded and seriously weakened |2.4.D.3| | 1 |
| rear brake recording little or no effort |3.7.B.5a| | 1 |
| All position lamps adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Direction indicators adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Nearside Rear Sub-frame attachment rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Sub-frame attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Offside Rear Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Hole in floor (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Hole in floor (7.1.1 (a) (i)) | 1 |
| Front Windscreen wiper not working (3.4 (a)) | 1 |
| Offside Rear Radius arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill outrigger (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill outrigger (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill area underneath seatbelt anchorage (7.1.1 (a) (i)) | 1 |
| Offside Floor excessively deteriorated corroded badly and holed by seat mount. (6.2.4 (a) (i)) | 1 |
| Front Windscreen wiper not working both (3.4 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area fractured significantly reducing structural strength strut top area. (5.3.6 (a) (i)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Rear Fluid suspension pipe leaking |2.4.D.2| | 1 |
| Dipswitch operation does not extinguish all main beam headlamps leaving at least one pair of dipped beam headlamps |1.7.4b| | 1 |
| Nearside Front Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 1 |
| Offside Front Headlamp not in a clean condition affecting beam image |1.2.4a| | 1 |
| Nearside Front Stop lamp not working |1.2.1b| | 1 |
| Offside Front Stop lamp not working |1.2.1b| | 1 |
| Offside Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Direction indicators not working |1.4.A.2c| | 1 |
| Nearside Direction indicator not working |1.4.A.2c| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Position lamp not working |4.2.1 |a|| | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn radius arm |5.3.4 |a| |i|| | 1 |
| Exhaust emissions hydrocarbon content excessive |8.2.1.2 |b|| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Braking system leaking around nearside rear flexi and brake compensator valve
|3.6.A.1| | 1 |
| Offside Rear Brake pipe inadequately clipped between subframe and fuel tank |3.6.B.1| | 1 |
| Fuel pipe excessively damaged tank breather pipe split around filler neck |7.2.2| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Nearside Front Lower Steering locking device ineffective ball joint (2.1.3 (d)) | 1 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 1 |
| Nearside Rear Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Driver`s seat cannot be secured in the upright position. |6.2.A.2| | 1 |
| Windscreen wiper blade insecure | 1 |
| Centre Front Lower Exhaust system not adequately supported |7.1.1| | 1 |
| Centre Front Brake cable locking device missing |3.5.1l| | 1 |
| Nearside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Exhaust system not adequately supported |7.1.1| | 1 |
| Steering component fractured and unserviceable |2.2.C.1d| | 1 |
| Offside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear wheel cylinder securing device missing |3.5.1j| | 1 |
| Offside Rear Direction indicator flashing less than 60 times a minute |1.4.A.2g| | 1 |
| Nearside Ball joint has excessive play |2.2.B.1f| | 1 |
| Headlamp not working on dipped beam both (4.1.1 (a) (ii)) | 1 |
| Headlamp not working on main beam both (4.1.1 (a) (ii)) | 1 |
| Position lamp not working all (4.2.1 (a) (ii)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Nearside Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| Offside Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| Offside Lower Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |