| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 32 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 30 |
| Registration plate lamp issues | 25 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 16 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 16 |
| Service brake: efficiency below requirements |3.7.B.7| | 15 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 15 |
| Brake hose excessively deteriorated | 14 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 13 |
| Offside Rear fog lamp not working |1.3.2b| | 12 |
| Parking brake: efficiency below requirements |3.7.B.7| | 12 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 10 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
| Brakes imbalanced across an axle | 9 |
| Windscreen wiper does not clear the windscreen effectively | 9 |
| Offside Steering rack gaiter split |2.2.D.2d| | 9 |
| Brake pipe excessively corroded | 8 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 7 |
| Rear parking brake recording little or no effort | 7 |
| Offside Side repeater not working |1.4.A.2c| | 7 |
| Nearside Stop lamp not working |1.2.1b| | 7 |
| Offside Stop lamp not working |1.2.1b| | 7 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 6 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Horn not working |1.6.2a| | 5 |
| Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 4 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Nearside Rear Radius arm has excessive play in a pin/bush |2.4.G.2| | 4 |
| Front brake application uneven | 4 |
| Offside Rear Sub-frame attachment rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 3 |
| Hazard warning switch faulty |1.4.B.1d| | 3 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Rear brake binding | 3 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 3 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Registration plate issues | 3 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 3 |
| Offside Rear Sub-frame attachment rubber mounting bonding deteriorated resulting in excessive movement |2.4.G.2| | 3 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Nearside Front Drag link end ball joint has excessive play |2.2.B.1f| | 3 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 3 |
| Front Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 3 |
| Offside Rear Radius arm has excessive play in a pin/bush |2.4.G.2| | 3 |
| Exhaust emissions carbon monoxide content excessive |8.2.1.2 |b|| | 3 |
| Centre Exhaust system not adequately supported |7.1.1| | 3 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 3 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 3 |
| Battery insecure |1.9.1| | 2 |
| Nearside Front Subframe mounting prescribed area is excessively corroded front panel |2.4.A.3| | 2 |
| Driver`s seat insecure |6.2.A.1| | 2 |
| Rear Exhaust system not adequately supported |7.1.1| | 2 |
| Offside Front Direction indicator not working |1.4.A.2c| | 2 |
| Rear Rear passenger seat cannot be secured in the upright position. |6.2.3| | 2 |
| Nearside Front Lower Shock absorber has an excessively worn bush |2.7.4| | 2 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Rear Fluid suspension unit supply pipe corroded and seriously weakened |2.4.D.3| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Nearside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 2 |
| Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside front brake binding |3.7.B.1| | 2 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| All position lamps not working |1.1.A.3b| | 2 |
| Nearside front brake binding |3.7.B.1| | 2 |
| Rear Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 2 |
| Mechanical brake component has restricted free movement | 2 |
| Nearside Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 2 |
| Offside Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 2 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Nearside Rear Sub-frame attachment rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Obligatory mirror missing |8.1.1| | 1 |
| Centre Obligatory mirror missing |8.1.1| | 1 |
| Offside Windscreen wiper blade missing |8.2.2| | 1 |
| Central Exhaust system not adequately supported |7.1.1| | 1 |
| Front Exhaust has a major leak of exhaust gases joint |7.1.2| | 1 |
| Offside Front Fluid suspension has no suspension movement |2.4.D.5| | 1 |
| Offside Rear Fluid suspension has no suspension movement |2.4.D.5| | 1 |
| Nearside Front Fluid suspension has no suspension movement |2.4.D.5| | 1 |
| Nearside Rear Fluid suspension has no suspension movement |2.4.D.5| | 1 |
| Emissions not tested |7.3.A.1| | 1 |
| Offside Obligatory mirror missing |8.1.1| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Brake hydraulic reservoir fluid level significantly below minimum level (1.1.10 (d) (ii)) | 1 |
| Nearside Sub-frame fractured mounting (5.3.3 (b) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases manifold (6.1.2 (a)) | 1 |
| Exhaust fumes entering cabin (6.1.2 (b) (i)) | 1 |
| Nearside Rear Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 1 |
| Steering column deformed steering wheel |2.1.3 |c| |i|| | 1 |
| Hazard warning switch inoperative |4.4.2 |a| |ii|| | 1 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Nearside Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Offside Rear Bumper damaged and likely to cause injury when grazed or contacted end cap missing |6.1.4 |a| |i|| | 1 |
| Nearside Rear Bumper likely to become detached end cap |6.1.4 |a| |ii|| | 1 |
| Front Fuel hose leaking |7.2.3| | 1 |
| Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Ball joint has excessive play |2.2.B.1f| | 1 |
| Front Lower Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Anti-roll bar synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Anti-roll bar synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Fuel system component leaking |7.2.3| | 1 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Fluid suspension has no suspension movement |2.4.D.5| | 1 |
| Central Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Front Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc and insecure. |2.5.C.1a| | 1 |
| Nearside Front Outer Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Outer Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded rear mount. inner wheel arch area and inner sill at jacking point. |2.4.A.3| | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded inner sill to inner wheel arch. |2.4.A.3| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded inner sill to wheel arch. |2.4.A.3| | 1 |
| Nearside front brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Front Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner sill to floor |5.2.6| | 1 |
| Offside Rear Sub-frame attachment rubber mounting deteriorated resulting in excessive movement front mounts |2.4.G.2| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded front panel |2.4.A.3| | 1 |
| Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded crossmember. |2.4.A.3| | 1 |
| An item not tested |Manual| | 1 |
| Stop lamp not working |1.2.1b| | 1 |
| Offside Front Subframe mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Nearside Rear Sub-frame attachment rubber mounting bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Nearside Rear Body has a projection caused by damage |6.1.C.1| | 1 |
| Offside Headlamp aim beam image too far to the left |1.6.B4| | 1 |
| Nearside Rear Fluid suspension unit supply pipe corroded and seriously weakened |2.4.D.3| | 1 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Rear Direction indicator excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Offside Front Brake hose leaking |3.6.A.1| | 1 |
| Nearside Rear Brake hose leaking |3.6.A.1| | 1 |
| Nearside Front Fluid suspension accumulator totally deflated |2.4.D.1a| | 1 |
| Offside Front Fluid suspension accumulator totally deflated |2.4.D.1a| | 1 |
| Nearside Outer Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Fuel cap/sealing device sealing washer deteriorated |7.2.4c| | 1 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Sub-frame rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Fluid suspension unit supply pipe corroded and seriously weakened |2.4.D.3| | 1 |
| Windscreen in an unacceptable condition |3.2 |c| |i|| | 1 |
| Brake pipe connection leaking on a hydraulic braking system Nearside front |1.1.11 |b| |ii|| | 1 |
| Nearside Rear Brake clevis joint insecure clip missing (1.1.15 (c)) | 1 |
| Offside Rear Brake clevis joint insecure clip missing (1.1.15 (c)) | 1 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Rear Fluid suspension unit interconnecting pipe corroded and seriously weakened |2.4.D.3| | 1 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Side repeater not working |1.4.A.2c| | 1 |
| Tailgate cannot be secured in the closed position |6.4.1| | 1 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Nearside Rear Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
| Front Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Windscreen wiper not working |3.4 |a|| | 1 |
| Offside Front Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Rear brake application uneven | 1 |
| Brake servo missing when fitted as standard |3.6.C.1a| | 1 |
| Nearside Rear Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Nearside Rear Axle beam has excessive vertical movement between stub axle and axle beam |2.5.A.1a| | 1 |
| Rear Statutory seat belt missing |5.1.1| | 1 |
| Front Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 1 |
| Exhaust engine idle speed too high |7.3.A.2a| | 1 |
| Nearside Rear Outer Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Rear Inner Subframe mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Brake hose leaking split during brake test |3.6.A.1| | 1 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Rear Rear fog lamp switch faulty |1.3.1a| | 1 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Body has a projection caused by damage |6.1.C.1| | 1 |
| Offside Front Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Offside Front Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Direction indicator not working |1.4.A.2c| | 1 |
| Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Rear Fluid suspension unit interconnecting pipe corroded and seriously weakened |2.4.D.3| | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Fluid suspension unit interconnecting pipe corroded and seriously weakened |2.4.D.3| | 1 |
| Nearside Front Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Radius arm worn and seriously weakened |2.4.G.1| | 1 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Emissions not tested started to overheat |8.2.1.2 |d|| | 1 |
| Windscreen washer not working | 1 |
| Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
| Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Nearside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Rear Rear fog lamp missing |1.3.2a| | 1 |
| Nearside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |7.1.4| | 1 |
| front brake binding Both sides |3.7.B.1| | 1 |
| Nearside Front All position lamps not working |1.1.A.3b| | 1 |
| Offside Front All position lamps not working |1.1.A.3b| | 1 |
| Nearside Rear All position lamps not working |1.1.A.3b| | 1 |
| Offside Rear All position lamps not working |1.1.A.3b| | 1 |
| Nearside Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Nearside Front suspension has excessive play in a track control arm inner bush |2.5.B.2b| | 1 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Rear Bonded suspension unit attachment damaged and seriously weakened |2.4.F.1c| | 1 |
| Offside Rear Bonded suspension unit attachment damaged and seriously weakened |2.4.F.1c| | 1 |
| Nearside Rear Radius arm has excessive play in a pin/bearing |2.4.G.2| | 1 |
| Offside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Brake pedal spongy |3.3.B.1b| | 1 |
| Nearside Rear Subframe mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected mount broken (5.3.6 (a) (ii)) | 1 |
| Offside Rear Subframe mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected mount broken (5.3.6 (a) (ii)) | 1 |
| Front Position lamp not working no frontside lights (4.2.1 (a) (ii)) | 1 |
| Rear Position lamp not working rear side light not working (4.2.1 (a) (ii)) | 1 |
| Exhaust emits excessive dense blue smoke during acceleration (8.2.1.2 (g)) | 1 |
| Direction indicators not working |1.4.A.2c| | 1 |
| Offside Rear Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Rear Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Rear Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Rear Subframe mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Rear Subframe mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Headlamp aim not tested |1.8.A.1c| | 1 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Nearside Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
| Rear Bonded suspension unit attachment damaged and seriously weakened |2.4.F.1c| | 1 |
| Centre Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Rear fog lamp switch faulty |1.3.1a| | 1 |
| Nearside Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Offside Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Nearside Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
| Offside Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front Body has a projection caused by damage |6.1.C.1| | 1 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Rear wheel cylinder leaking |3.6.A.1| | 1 |
| Nearside Side repeater not working |1.4.A.2c| | 1 |
| Nearside Front Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Offside Front Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Offside Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 1 |
| Nearside Rear Brake pivot has restricted free movement |3.5.1k| | 1 |
| Front Fluid suspension has no suspension movement |2.4.D.5| | 1 |
| Rear Fluid suspension has no suspension movement |2.4.D.5| | 1 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Rear Braking system leaking |3.6.A.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch |5.3.6 |a| |i|| | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Offside Front Lower Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
| Offside Front Body insecure and dangerous to other road users wing |6.1.B.1b| | 1 |
| Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Front brake disc has restricted free movement |3.5.1j| | 1 |
| Offside Front brake disc has restricted free movement |3.5.1j| | 1 |
| Nearside Rear Sub-frame attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Offside Rear Sub-frame attachment bracket/mounting insecure |2.4.G.1| | 1 |