| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 33 |
| Windscreen wiper does not clear the windscreen effectively | 25 |
| Brake pipe excessively corroded | 15 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 14 |
| Rear brake binding | 13 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 8 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Brakes imbalanced across an axle | 7 |
| Parking brake: efficiency below requirements |3.7.B.7| | 7 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Registration plate lamp issues | 6 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 5 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 5 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Brake pedal spongy |3.3.B.1b| | 5 |
| Brake hose excessively deteriorated | 4 |
| Offside Stop lamp not working |1.2.1b| | 4 |
| Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Offside Steering rack gaiter split |2.2.D.2d| | 4 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 4 |
| Rear parking brake recording little or no effort | 4 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Rear brake application uneven | 4 |
| Nearside Stop lamp not working |1.2.1b| | 3 |
| Brake pedal anti-slip provision missing |3.3.A.1b| | 3 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Front Shock absorber has negligible damping effect |2.7.5| | 3 |
| Offside Rear wheel bearing rough when rotated |2.6.1| | 3 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 3 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Registration plate issues | 3 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 3 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Parking brake lever has no reserve travel |3.1.6b| | 3 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
| Windscreen has damage | 3 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
| Nearside Front Shock absorber has negligible damping effect |2.7.5| | 2 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Rear fog lamp not working |1.3.2b| | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 2 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
| Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 2 |
| Rear fog lamp tell tale not working |1.3.1b| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Service brake indicates brake bind |3.7.D.2a| | 2 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 2 |
| Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Macpherson strut corroded and seriously weakened |2.4.G.1| | 2 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Fuel cap/sealing device sealing washer deteriorated |7.2.4c| | 2 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 2 |
| Offside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Nearside Front Brake hose leaking |3.6.A.1| | 2 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 2 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 2 |
| Nearside Front Body has a sharp edge caused by damage |6.1.C.1| | 2 |
| Offside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Service brake: efficiency below requirements |3.7.B.7| | 2 |
| Nearside front brake binding |3.7.B.1| | 2 |
| Offside front brake binding |3.7.B.1| | 2 |
| Offside Rear Stop lamp not working |1.2.1b| | 2 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced center floor (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded bulk head |2.4.A.3| | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 1 |
| Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded under bonnet |2.4.A.3| | 1 |
| Nearside Ball joint has excessive play inner rack |2.2.B.1f| | 1 |
| Fuel cap/sealing device mounting flange/sealing method defective |7.2.4c| | 1 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Offside Rear reflector excessively damaged so that its function is impaired |1.5.1c| | 1 |
| Inner Obligatory mirror missing |8.1.1| | 1 |
| Driver`s seat insecure |6.2.A.1| | 1 |
| Driver`s seat cannot be secured in the upright position. |6.2.A.2| | 1 |
| Nearside Rear Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |
| Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Nearside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Windscreen washer not working | 1 |
| Nearside Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 1 |
| Exhaust emits dense blue smoke at idle |7.3.A.2b| | 1 |
| An item not tested |Manual| | 1 |
| Offside Front Side repeater incorrect colour |1.4.A.2f| | 1 |
| Offside Rear Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Nearside Front Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Offside Macpherson strut has excessive movement at the upper attachment |2.5.A.1c| | 1 |
| Nearside Rear Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
| Windscreen wiper blade insecure | 1 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Headlamp aim beam image too far to the left |1.6.B4| | 1 |
| Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Inner Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Outer Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Outer Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Steering damper leaking oil |2.2.C.1f| | 1 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Outer Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Inner Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Inner Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Offside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Statutory seat belt missing |5.1.1| | 1 |
| Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Steering locking device ineffective (2.1.3 (d)) | 1 |
| Offside Steering locking device ineffective (2.1.3 (d)) | 1 |
| Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Fuel system component leaking |7.2.3| | 1 |
| Offside Front Macpherson strut corroded and seriously weakened |2.4.G.1| | 1 |
| Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 1 |
| Nearside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 1 |
| Offside Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Offside Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
| Front Macpherson strut has excessive movement at the upper attachment |2.5.A.1c| | 1 |
| Front Macpherson strut upper support bearing is rough in operation |2.5.B.1b| | 1 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Nearside Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Stop lamp not working |1.2.1b| | 1 |
| Front Macpherson strut corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Rear fog lamp not working |1.3.2b| | 1 |
| Headlamp not working on main beam |1.7.5a| | 1 |
| Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Front Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Offside Front Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Emissions not tested |7.0| | 1 |
| Front Fuel pipe leaking |7.2.3| | 1 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Fuel cap/sealing device missing |7.2.4a| | 1 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Offside Front Obligatory mirror insecure |8.1.1| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Brake cable has restricted free movement |3.5.1k| | 1 |
| Nearside Outer Rear Upper Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Offside Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Side repeater not working |1.4.A.2c| | 1 |
| Nearside Side repeater incomplete |1.5.A1b| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Rear Mechanical brake component has restricted free movement | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front of wheel tub (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis within 30cm of shocker support (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis within 30cm of shocker support (5.3.6 (a) (i)) | 1 |
| Nearside Front Direction indicator excessively deteriorated so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Nearside Rear Rear position lamp|s| incomplete |1.1.4a| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Obligatory mirror seriously deteriorated, affecting the rear view |8.1.2a| | 1 |
| Offside Front Obligatory mirror seriously deteriorated, affecting the rear view |8.1.2a| | 1 |
| Exhaust emissions hydrocarbon content excessive |8.2.1.2 |b|| | 1 |
| Offside Rear Brake hose leaking |3.6.A.1| | 1 |
| Offside Front Headlamp insecure (4.1.1 (c)) | 1 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wheel arch
chassis has a rust hole (6.2.2 (d) (i)) | 1 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Exhaust engine idle speed too high |7.3.A.2a| | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Nearside Front Outer Passengers seat with a defective structure outer sill bottom of A pillar (6.2.6 (a) (i)) | 1 |
| Nearside Rear Brake hose excessively damaged (1.1.12 (b) (ii)) | 1 |
| Nearside Rear Parking brake lever inoperative (1.1.6 (d)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill at rear (7.1.1 (a) (i)) | 1 |
| Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill heavy rust (7.1.1 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Direction indicator excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front An item not tested |Manual| | 1 |
| Offside Front An item not tested |Manual| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Offside Rear Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Upper Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Brake pedal creeps down when held under pressure |3.3.B.1a| | 1 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Rear position lamp|s| obviously incorrectly positioned |1.1.A.3a| | 1 |
| rear brakes release unevenly |3.7.B.4| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Central Front Shock absorbers has a serious fluid leak |5.3.2 |b|| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced rear of b post (7.1.1 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Exhaust emissions carbon monoxide content excessive 4.439 . ( max is 3.5) (8.2.1.2 (b)) | 1 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Rear Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension arm pin or bush excessively worn forward bush (5.3.4 (a) (i)) | 1 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded sill/door step/inner sill and wheel arch |5.2.6| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded sill/door step/inner sill and wheel arch. |5.2.6| | 1 |
| Nearside Front Side repeater not working |1.4.A.2c| | 1 |
| Nearside Rear Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Offside Front Macpherson strut has excessive movement at the upper attachment |2.5.A.1c| | 1 |
| Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Steering rack insecure |2.2.B.1a| | 1 |