Most common failures | No# failures |
---|
Brakes imbalanced across an axle | 20 |
Headlamp aim out of alignment | 17 |
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 16 |
Parking brake: efficiency below requirements |3.7.B.7| | 13 |
Windscreen wiper does not clear the windscreen effectively | 10 |
Nearside Steering rack gaiter split |2.2.D.2d| | 8 |
Registration plate lamp issues | 7 |
Brake pipe excessively corroded | 7 |
Offside Steering rack gaiter split |2.2.D.2d| | 6 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 6 |
Rear brake binding | 6 |
Rear parking brake recording little or no effort | 6 |
Service brake: efficiency below requirements |3.7.B.7| | 5 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 4 |
Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
Front brake application uneven | 4 |
Nearside Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 4 |
Nearside Rear wheel bearing has excessive play |2.6.2| | 3 |
Offside Rear wheel bearing has excessive play |2.6.2| | 3 |
Nearside Stop lamp not working |1.2.1b| | 3 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 3 |
Rear brake application uneven | 3 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 2 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Nearside front brake binding |3.7.B.1| | 2 |
Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 2 |
Nearside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
Brake hose excessively deteriorated | 2 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside front brake binding |3.7.B.1| | 2 |
Emissions not tested |7.0| | 2 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Rear Bonded suspension unit bonding failed and part of unit is likely to become displaced |2.4.F.2| | 2 |
Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
Offside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
Parking brake lever has no reserve travel |3.1.6b| | 2 |
All position lamps not working |1.1.A.3b| | 2 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 2 |
Rear Mechanical brake component has restricted free movement | 2 |
Offside Headlamp insecure |1.7.3| | 1 |
Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
Nearside Rear Fluid suspension unit leaking |2.4.D.2| | 1 |
Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength marked |5.3.6 |a| |i|| | 1 |
Offside Front Suspension component ball joint dust cover no longer prevents the ingress of dirt suspension unit dust cover detached |5.3.4 |b| |ii|| | 1 |
Headlamp switch faulty |1.7.1| | 1 |
Nearside Headlamp aim beam image kick up to the offside |1.6.B1| | 1 |
Offside Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
Direction indicators not working |1.4.A.2c| | 1 |
Hazard warning lamps inoperative |1.4.B.1b| | 1 |
Horn not working (7.7 (a) (ii)) | 1 |
Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Outer Rear Radius arm rubber mounting bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Outer Rear Radius arm rubber mounting bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
Offside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
Direction indicators flashing more than 120 times a minute |1.4.A.2g| | 1 |
Fuel pipe leaking |7.2.3| | 1 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Front Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Rear Stop lamp not working |1.2.1b| | 1 |
Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Offside Front front brake binding |3.7.B.1| | 1 |
Nearside Front front brake binding |3.7.B.1| | 1 |
Nearside Rear front brake binding |3.7.B.1| | 1 |
Nearside Steering arm has relative movement at its fixings |2.2.B.1h| | 1 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Inner Ball joint has excessive play drum stick |2.2.B.1f| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded inner wing area |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded inner and outer sill areas |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front Subframe (5.3.6 (a) (i)) | 1 |
Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front Cross Member (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner Arch (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner Arch (5.3.6 (a) (i)) | 1 |
Rear Position lamp adversely affected by the operation of another lamp Rear Position Lamps Inoperative With Headlights On (4.2.3 (c)) | 1 |
Offside Front Position lamp not working |4.2.1 |a|| | 1 |
Nearside Front Service brake excessively binding |1.2.1 |f|| | 1 |
Nearside Front Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
Exhaust emissions hydrocarbon content excessive 3059/1200 (8.2.1.2 (b)) | 1 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Nearside Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
Offside Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
Battery insecure |1.9.1| | 1 |
Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Steering rack damaged and unserviceable |2.2.C.1d| | 1 |
Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Brake master cylinder leaking hydraulic fluid |3.6.G.1f| | 1 |
Offside Front Lower Front suspension has excessive movement at a suspension ball joint |2.5.A.1c| | 1 |
Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Nearside Front Steering column shaft has excessive end float |2.1.3| | 1 |
Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
Stop lamp not working |1.2.1b| | 1 |
Offside Steering arm deformed and unserviceable |2.2.C.1d| | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Position lamp not working |4.2.1 |a|| | 1 |
Nearside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
Nearside Front Suspension arm ball joint likely to become detached coming undone |5.3.4 |a| |ii|| | 1 |
Offside Rear Outer Suspension arm pin or bush excessively worn radius arm mount rubber split (5.3.4 (a) (i)) | 1 |
Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Offside Obligatory mirror missing |8.1.1| | 1 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Nearside Rear Bonded suspension unit bonding failed and part of unit is likely to become displaced |2.4.F.2| | 1 |
Nearside Upper Ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Lower Ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
Steering wheel retaining device insecure |2.1.6| | 1 |
Offside Rear Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
Steering rack damaged and unserviceable |2.2.C.1d| | 1 |
Steering system excessively tight |2.2.D.1| | 1 |
Hazard warning switch faulty |1.4.B.1d| | 1 |
Nearside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
Brake performance not tested |3.7.A.1| | 1 |
Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 1 |
Direction indicators flashing less than 60 times a minute |1.4.A.2g| | 1 |
Central Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Rear Hydraulic brake cylinder leaking hydraulic fluid |3.6.A.1| | 1 |
Central Front Suspension component mounting prescribed area is excessively corroded cross member |2.4.A.3| | 1 |
Offside Rear Direction indicator not working |4.4.1 |a| |ii|| | 1 |
Nearside Rear Wheel bearing play so excessive it is likely to break up |5.1.3 |a| |ii|| | 1 |
Offside Rear Wheel bearing play so excessive it is likely to break up |5.1.3 |a| |ii|| | 1 |
Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
Nearside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Offside Rear wheel cylinder leaking |3.6.A.1| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Steering arm has relative movement at its fixings |2.2.B.1h| | 1 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Headlamp aim not tested |1.8.A.1c| | 1 |
Offside Front brake caliper has restricted free movement |3.5.1k| | 1 |
Nearside Front Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 1 |
Offside Front Direction indicator not working |1.4.A.2c| | 1 |
Nearside Rear Stop lamp not working |1.2.1b| | 1 |
Offside Front Braking system leaking |3.6.A.1| | 1 |
Nearside Front Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Front Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Front Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 1 |
Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Front Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
Nearside Parking brake inoperative on one side Low performance (1.4.1 (a)) | 1 |
Suspension system inoperative Front end collapsed (5.3.5 (a)) | 1 |
Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
Nearside Rear Hydraulic brake cylinder leaking and braking performance affected Dripping from brake drum (1.1.16 (b) (ii)) | 1 |
Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
Offside Rear Anti-roll bar linkage insecure |2.4.G.1| | 1 |
Offside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
Nearside Rear Direction indicator flashing less than 60 times a minute |1.4.A.2g| | 1 |