Most common failures | No# failures |
---|
Headlamp aim out of alignment | 9 |
Registration plate issues | 8 |
Drive chain excessively loose |6.2.1d| | 8 |
Rear reflector on motorcycle missing |1.4.1| | 6 |
Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 5 |
Horn not working |1.7.3a| | 4 |
Rear Position lamp not working (4.2.1 (a)) | 4 |
Rear reflector missing (4.8.2 (a) (ii)) | 4 |
Rear wheel bearings have excessive free play |2.4.A.2c| | 3 |
Registration plate lamp issues | 3 |
Front Brake indicates excessive fluctuation of brake effort (1.2.1 (e)) | 3 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 3 |
Offside Front Front shock absorber seal failed and leaking oil |2.3.3| | 3 |
Rear Wheel spoke missing |4.2.1b| | 3 |
Rear reflector on motorcycle obscured |1.4.2b| | 2 |
Nearside Rear Direction indicators not working |1.5.1c| | 2 |
Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 2 |
Rear reflector missing |4.8.2 |a| |ii|| | 2 |
Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
Exhaust is leaking and excessively noisey |7.1.1b| | 2 |
Nearside Front Front shock absorber seal failed and leaking oil |2.3.3| | 2 |
Horn not working |7.7 |a| |ii|| | 2 |
Fuel system component leaking Carburettor leaking fuel |7.2.1a| | 1 |
Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride Drive chain link plate on the wrong way round |6.2.1h| | 1 |
Rear Brake pedal has inadequate reserve travel |3.1.3b| | 1 |
Roller brake test No brake control achieves an efficiency of 30%. |3.3.A2a| | 1 |
Rear Shock absorber has a serious fluid leak (5.3.2 (b)) | 1 |
Rear Lower Shock absorber has an excessively worn bush (5.3.2 (c)) | 1 |
Rear Brake fluid contaminated (1.8 (a)) | 1 |
Stop lamp not working from rear brake |4.3.1 |a| |ii|| | 1 |
Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
Rear Brake disc contaminated |1.1.14 |b|| | 1 |
Rear Brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 1 |
Front Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
Rear Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
Front Brake lever is so short that the brake cannot be readily applied |1.1.2 |d|| | 1 |
Roller brake test The less effective brake control does not achieve an efficiency of 25% |1.2.2 |a| |i|| | 1 |
Nearside Rear Direction indicator not working |4.4.1 |a| |ii|| | 1 |
Rear Stop lamp affected by the operation of another lamp |1.3.2| | 1 |
Front Stop lamp affected by the operation of another lamp |1.3.2| | 1 |
Nearside Rear Footrest missing (6.2.12 (a)) | 1 |
Offside Rear Footrest missing (6.2.12 (a)) | 1 |
Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Horn sounds harsh or grating |1.7.3c| | 1 |
Stop lamp remains on when the brake is released |1.3.1e| | 1 |
Front Brake hose is likely to be fouled or trapped by moving parts |3.2.B2c| | 1 |
Headlamp insecure |1.2.3b| | 1 |
Headlamp aim not tested |1.6| | 1 |
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Fuel cap mounting flange/sealing method defective |7.2.2c| | 1 |
Footrest missing PIllion. (6.2.12 (a)) | 1 |
Stop lamp not working Control 1 (4.3.1 (a) (ii)) | 1 |
Rear Brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii)) | 1 |
Roller brake test The less effective brake control does not achieve an efficiency of 25% (1.2.2 (a) (i)) | 1 |
Exhaust noise is clearly in excess of that emitted by a similar motor bicycle fitted with a standard silencer in average condition |7.1.2| | 1 |
Front Direction indicator incorrect colour |1.5.1b| | 1 |
Rear Direction indicator incorrect colour |1.5.1b| | 1 |
Front Roller brake test indicates a severely grabbing brake |3.3.A1b| | 1 |
Rear Brake disc fractured cracks in disc (1.1.14 (a) (ii)) | 1 |
All direction indicators adversely affected by the operation of another lamp indicators stop flashing when brake light is used, bike does not seem to have battery power (4.4.3 (b)) | 1 |
Rear Brake excessively binding (1.2.1 (f)) | 1 |
Rear suspension movement is excessively stiff |2.4.A.3b| | 1 |
Offside Rear Brake hose leaking fluid |3.2.B4| | 1 |
All position lamps not working |4.2.1 |a|| | 1 |
Wheel alignment incorrect which adversely affects the steering |2.4 |a|| | 1 |
Stop lamp does not illuminate by the operation of both brake controls not working with front (4.3.2 (a) (iii)) | 1 |
Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Front Stop lamp not working |4.3.1 |a| |ii|| | 1 |
Handlebar deformed |2.1.1b| | 1 |
Front Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Nearside Handlebar handgrip not secure to handlebars. |2.1.1c| | 1 |
Steering movement excessively `notchy` with the weight on the lower bearing steering locking up |2.2.1a| | 1 |
Nearside Rear Direction indicators not working not working all the time |1.5.1c| | 1 |
Offside Rear Direction indicators not working not working all the time |1.5.1c| | 1 |
Locking devices not correctly fitted which may make the motor bicycle dangerous to ride clutch lever lock nut |6.2.1h| | 1 |
Exhaust mounting missing front exhaust spring |7.1.1c| | 1 |
Exhaust mounting does not fully support the exhaust system front exhaust bracket broken |7.1.1.c| | 1 |
Offside Upper Front suspension assembly component missing fork pinch bolt missing |2.3.1| | 1 |
Brake component defective due to a deliberate modification which significantly reduces the original strength front brake assembly does not match to brake disc |3.1.5| | 1 |
Offside Front Wheel spoke excessively loose one spoke |4.2.1b| | 1 |
Rear wheel bearings are excessively tight |2.4.A.2c| | 1 |
Stop lamp remains on when the brake is released front brake |1.3.1e| | 1 |
Steering headbearing has excessive free play |2.2.2| | 1 |
Brake lever is so short and the brake cannot be readily applied |3.1.3c| | 1 |
Lower Rear suspension bush has excessive free play |2.4.A2a|i|| | 1 |
Drive chain excessively loose (6.1.7 (c) (i)) | 1 |
Nearside Front Direction indicator flashing more than 120 times per minute |1.5.1c| | 1 |
Rear Rear reflector missing (4.8.2 (a) (ii)) | 1 |
Rear Brake fluid reservoir fluid level significantly below minimum level (1.1.10 (d) (ii)) | 1 |
Horn sound not in accordance with requirements (7.7 (c)) | 1 |
Drive chain so worn it is likely to fail (6.1.7 (c) (ii)) | 1 |
Drive chain so loose it is likely to fail (6.1.7 (c) (ii)) | 1 |
Rear Drive chain sprocket so worn it is likely to fail (6.1.7 (c) (ii)) | 1 |
Offside Front Upper Brake lever has abnormal movement of levers indicating excessive wear or maladjustment (1.1.15 (f)) | 1 |
Front Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
Nearside Rear Direction indicator not working |1.5.1c| | 1 |
Offside Rear Direction indicator not working |1.5.1c| | 1 |
Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride chain link fitted in wrong direction |6.2.1h| | 1 |
Brake lever is damaged and the brake cannot be readily applied |3.1.3c| | 1 |
Brake pedal insecure |3.1.2a| | 1 |
Handlebar mounting clamp bolt loose top yoke bolt loose |2.1.1a| | 1 |
Front Front wheel bearings are excessively rough |2.3.5b| | 1 |
Front Front wheel spindle securing nut locking device missing |2.3.3a| | 1 |
Front wheel insecure spokes not clearance colper |4.2.3b| | 1 |
Rear Brake caliper inadequately mounted caliper slider guide rubber missing (1.1.16 (c) (i)) | 1 |
Rear Brake cylinder leaking (1.1.16 (b) (i)) | 1 |
Upper Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Rear Shock absorber likely to become detached inadequate repair (wrong shock absorber?) (5.3.2 (a) (ii)) | 1 |
Front Brake disc contaminated (1.1.14 (b)) | 1 |
Brake master cylinder defective but brake still operating brake lever moves but effort does not increase (1.1.10 (b) (i)) | 1 |
Rear Drive chain sprocket worn to excess |6.2.1e| | 1 |
Front Drive chain sprocket worn to excess |6.2.1e| | 1 |
Horn not working (7.7 (a) (ii)) | 1 |
Front Stop lamp not working (4.3.1 (a) (ii)) | 1 |
Rear Suspension component has excessive wear or free play (5.3.3 (d)) | 1 |
Headlamp aim not tested |4.1.2 |b|| | 1 |
Front Position lamp not working headlight in-op |4.2.1 |a|| | 1 |
All direction indicators not working |4.4.1 |a| |ii|| | 1 |
Nearside Front Shock absorber has a serious fluid leak |5.3.2 |b|| | 1 |
Drive chain excessively loose |6.1.7 |c| |i|| | 1 |
Front Wheel spoke excessively loose Multiple |4.2.1b| | 1 |
Rear Wheel spoke excessively loose Multiple |4.2.1b| | 1 |
Brake performance not tested |3.3| | 1 |
Front Floor brake test indicates a binding brake |3.3.C2c| | 1 |
Front Wheel spoke excessively loose |4.2.1b| | 1 |
Rear Wheel spoke excessively loose |4.2.1b| | 1 |
Brake performance not tested Due to front brake bind and loose spokes. |3.3| | 1 |
Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 1 |
Front Wheel spindle locking device missing (5.2.1 (d)) | 1 |
Offside Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 1 |
Throttle operating incorrectly Sticks open |6.2.1f| | 1 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 1 |
Direction indicators not working |1.5.1c| | 1 |
Rear Brake fluid reservoir fluid level dangerously low |3.2.B1d| | 1 |
Horn not loud enough to be heard by another road user |1.7.3a| | 1 |
Brake pedal has inadequate reserve travel |3.1.3b| | 1 |
Indicator tell tale not functioning |1.5.2| | 1 |
Front Steering movement excessively `notchy` with the weight on the lower bearing |2.2.1a| | 1 |
Front Throttle operating incorrectly throttle cable split and not sitting in holder so no operating correctly |6.2.1f| | 1 |
Vehicle identification number not permanently displayed |6.3.5a| | 1 |
Nearside Front Handlebar handgrip not secure to handlebars. |2.1.1c| | 1 |
Offside Front Handlebar handgrip missing |2.1.1c| | 1 |
Wheel spoke missing 3 spokes missing from rear wheel (5.2.2 (d)) | 1 |
Stop lamp light intensity significantly reduced (4.3.3 (a) (ii)) | 1 |
Stop lamp not working (4.3.1 (a) (ii)) | 1 |
Headlamp aim not tested (4.1.2 (b)) | 1 |
Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Rear Position lamp lens seriously defective (4.2.1 (b)) | 1 |
Rear Stop lamp with a multiple light source more than 1/2 not functioning (4.3.1 (a) (ii)) | 1 |
Front Stop lamp with a multiple light source more than 1/2 not functioning (4.3.1 (a) (ii)) | 1 |