Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 311 |
Registration plate lamp issues | 293 |
Brakes imbalanced across an axle | 217 |
Brake hose excessively deteriorated | 162 |
Headlamp aim out of alignment | 148 |
Nearside Steering rack gaiter split |2.2.D.2d| | 125 |
Offside Steering rack gaiter split |2.2.D.2d| | 117 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 117 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 112 |
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 89 |
Nearside front brake binding |3.7.B.1| | 81 |
Offside front brake binding |3.7.B.1| | 74 |
Exhaust has a major leak of exhaust gases |7.1.2| | 68 |
Rear brake application uneven | 60 |
Horn not working |1.6.2a| | 58 |
Nearside Stop lamp not working |1.2.1b| | 58 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 56 |
Offside Stop lamp not working |1.2.1b| | 56 |
Nearside Front Steering rack gaiter split |2.2.D.2d| | 53 |
Offside Rear fog lamp not working |1.3.2b| | 51 |
Brake pipe excessively corroded | 50 |
Offside Front Steering rack gaiter split |2.2.D.2d| | 49 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 47 |
Hazard warning switch faulty |1.4.B.1d| | 46 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 46 |
Offside Front front brake binding |3.7.B.1| | 46 |
Rear brake binding | 45 |
Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 44 |
Battery insecure |1.9.1| | 43 |
Parking brake: efficiency below requirements |3.7.B.7| | 43 |
Rear parking brake recording little or no effort | 42 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 41 |
Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 41 |
Direction indicators not working |1.4.A.2c| | 41 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 39 |
Registration plate issues | 37 |
Exhaust system not adequately supported |7.1.1| | 35 |
Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 34 |
Rear Exhaust system not adequately supported |7.1.1| | 34 |
Rear fog lamp not working |1.3.2b| | 34 |
Hazard warning lamps inoperative |1.4.B.1b| | 32 |
Nearside Front front brake binding |3.7.B.1| | 31 |
Service brake: efficiency below requirements |3.7.B.7| | 31 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 31 |
Offside rear brake recording little or no effort |3.7.B.5a| | 31 |
Centre Exhaust system not adequately supported |7.1.1| | 31 |
Rear fog lamp tell tale not working |1.3.1b| | 30 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 28 |
Front brake application uneven | 28 |
Nearside Rear wheel bearing rough when rotated |2.6.1| | 27 |
Offside Rear wheel bearing rough when rotated |2.6.1| | 26 |
Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 23 |
Windscreen washer not working | 22 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 22 |
Mechanical brake component has restricted free movement | 22 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 21 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 21 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 21 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 20 |
Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 20 |
Offside Rear rear brake recording little or no effort |3.7.B.5a| | 20 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 19 |
Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 19 |
Offside Rear Rear fog lamp not working |1.3.2b| | 19 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 18 |
Offside Rear Stop lamp not working |1.2.1b| | 18 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 18 |
Emissions not tested |7.0| | 18 |
Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 17 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 17 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 17 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 17 |
Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 16 |
Stop lamp not working |1.2.1b| | 16 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 16 |
Nearside Rear Stop lamp not working |1.2.1b| | 15 |
Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 15 |
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 15 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 15 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 15 |
Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 15 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 14 |
Fuel cap/sealing device sealing washer torn |7.2.4c| | 14 |
Offside Side repeater not working |1.4.A.2c| | 14 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 14 |
Nearside Front Direction indicator not working |1.4.A.2c| | 14 |
Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 14 |
Front Exhaust system not adequately supported |7.1.1| | 14 |
Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 14 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 13 |
Offside Front position lamp|s| not working |1.1.A.3b| | 13 |
Hazard warning switch inoperative |4.4.2 |a| |ii|| | 13 |
Hazard warning switch inoperative (4.4.2 (a) (ii)) | 12 |
Nearside Front Service brake excessively binding |1.2.1 |f|| | 12 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 12 |
Nearside Rear wheel bearing has excessive play |2.6.2| | 12 |
Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 12 |
Nearside Front Side repeater not working |1.4.A.2c| | 11 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 11 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 11 |
Nearside Rear Direction indicator not working |1.4.A.2c| | 11 |
Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 11 |
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 11 |
Emissions not tested (8.2.1.2 (d)) | 10 |
Hazard warning tell tale not working correctly |1.4.B.1e| | 10 |
Rear Brake load sensing valve linkage seized |3.6.E.3| | 10 |
Offside Front Direction indicator not working |1.4.A.2c| | 10 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 10 |
Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 10 |
Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 10 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 10 |
Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 10 |
Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 10 |
Offside Rear wheel bearing has excessive play |2.6.2| | 9 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 9 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 9 |
Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 9 |
Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 9 |
Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 9 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 9 |
Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 9 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 9 |
Offside Headlamp not working on dipped beam |1.7.5a| | 9 |
Offside Rear Direction indicator not working |1.4.A.2c| | 9 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
Exhaust mounting missing |7.1.1b| | 9 |
Fuel cap/sealing device sealing washer deteriorated |7.2.4c| | 9 |
Hazard warning lamps inoperative (4.4.1 (e)) | 9 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 9 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 9 |
Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 9 |
All direction indicators not working (4.4.1 (a) (ii)) | 8 |
Nearside Rear Service brake excessively binding (1.2.1 (f)) | 8 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 8 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 8 |
Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 8 |
Nearside Side repeater not working |1.4.A.2c| | 8 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
Exhaust has part of the system excessively deteriorated |7.1.1a| | 8 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
Parking brake lever has no reserve travel |3.1.6b| | 8 |
Windscreen wiper blade insecure | 8 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 8 |
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 8 |
Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 8 |
Brake hose damaged | 8 |
Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 8 |
Offside Front Windscreen wiper blade deteriorated |8.2.2| | 8 |
front brake binding |3.7.B.1| | 8 |
Front brake disc in such a condition that it is seriously weakened | 8 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 8 |
Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 7 |
Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 7 |
Offside Front Service brake excessively binding |1.2.1 |f|| | 7 |
Windscreen wiper not working (3.4 (a)) | 7 |
Brake load sensing valve linkage seized |3.6.E.3| | 7 |
Brake load sensing valve seized |3.6.E.3| | 7 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 7 |
Offside Windscreen wiper blade deteriorated |8.2.2| | 7 |
Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 7 |
Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 7 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 7 |
Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 7 |
Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 7 |
Exhaust system insecure (6.1.2 (a)) | 7 |
Offside Front Anti-roll bar linkage fractured |2.4.G.1| | 7 |
Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 7 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
Rear Stop lamp not working |1.2.1b| | 7 |
Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 7 |
Horn not working (7.7 (a) (ii)) | 6 |
Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 6 |
Nearside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 6 |
Offside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 6 |
Offside Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 6 |
Nearside Front Steering arm has relative movement at its fixings |2.2.B.1h| | 6 |
rear brakes release unevenly |3.7.B.4| | 6 |
Offside Front Position lamp not working |4.2.1 |a|| | 6 |
Stop lamp|s| all not working |4.3.1 |a| |iii|| | 6 |
Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 6 |
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
Steering rack gaiter split |2.2.D.2d| | 6 |
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
All direction indicators not working |4.4.1 |a| |ii|| | 6 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 6 |
Rear Rear fog lamp not working |1.3.2b| | 6 |
Nearside Front Direction indicators not working |1.4.A.2c| | 6 |
Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 6 |
Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Centre Exhaust mounting missing |7.1.1b| | 6 |
Rear Exhaust mounting missing |7.1.1b| | 6 |
Offside Steering rack gaiter insecure |2.2.D.2d| | 6 |
Nearside Front brake disc excessively pitted |3.5.1h| | 6 |
Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 6 |