Most common failures | No# failures |
---|
Parking brake: efficiency below requirements |3.7.B.7| | 23 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
Windscreen wiper does not clear the windscreen effectively | 10 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Headlamp aim out of alignment | 5 |
Rear parking brake recording little or no effort | 5 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Brakes imbalanced across an axle | 5 |
Brake pipe excessively corroded | 5 |
Nearside Headlamp aim beam image kick up to the offside |1.8| | 4 |
Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 4 |
Rear brake binding | 4 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 3 |
Offside Headlamp not working on dipped beam |1.7.5a| | 3 |
Registration plate lamp issues | 3 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Front Direction indicator not working |1.4.A.2c| | 3 |
Offside Front front brake binding |3.7.B.1| | 3 |
Offside Front Shock absorbers has a serious fluid leak | 2 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
Rear fog lamp tell tale not working |1.3.1b| | 2 |
Fuel system component leaking |7.2.3| | 2 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 2 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Horn not working |1.6.2a| | 2 |
Hazard warning switch faulty |1.4.B.1d| | 2 |
Offside front brake binding |3.7.B.1| | 2 |
Nearside Headlamp not working on main beam |1.7.5a| | 2 |
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Offside Headlamp aim beam image kick up to the offside |1.8| | 2 |
Fuel pipe leaking |7.2.3| | 2 |
Service brake: efficiency below requirements |3.7.B.7| | 2 |
Nearside Side repeater not working |1.4.A.2c| | 2 |
Horn sound not in accordance with requirements (7.7 (c)) | 2 |
Parking brake lever ratchet not holding correctly (1.1.6 (a)) | 2 |
Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
Windscreen washer not working | 2 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
Nearside Front front brake binding |3.7.B.1| | 2 |
Registration plate issues | 2 |
Nearside Rear Direction indicator not working |1.4.A.2c| | 2 |
Offside Rear fog lamp not working |1.3.2b| | 2 |
Windscreen has damage | 2 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
Nearside Inner Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Rear Leaf spring anchor bracket loose |2.4.B.6a| | 1 |
Windscreen wiper blade insecure | 1 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Offside Front Direction indicator insecure |1.4.A.2b| | 1 |
Offside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Direction indicators not working |1.4.A.2c| | 1 |
Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 1 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside front brake grabbing severely |3.7.A.2b| | 1 |
Offside front brake grabbing severely |3.7.A.2b| | 1 |
Offside Rear fog lamp insecure |1.3.2a| | 1 |
Nearside Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Torsion bar insecure at an end fixing |2.4.E.2| | 1 |
Offside Front Torsion bar insecure at an end fixing |2.4.E.2| | 1 |
Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Brake performance not tested |3.7.A.1| | 1 |
Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill-various places-marked (6.1.1 (c) (i)) | 1 |
Nearside Front Suspension arm pin or bush excessively worn front and rear (5.3.4 (a) (i)) | 1 |
Offside Front Suspension arm pin or bush excessively worn front and rear (5.3.4 (a) (i)) | 1 |
Parking brake lever has no reserve travel |3.1.6b| | 1 |
Nearside front brake binding |3.7.B.1| | 1 |
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
Exhaust emissions exceed manufacturer`s specified limit |8.2.2.2 |a|| | 1 |
Offside Front Service brake excessively binding |1.2.1 |f|| | 1 |
Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Offside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Nearside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill section (6.1.1 (c) (i)) | 1 |
Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
Hazard warning lamps inoperative (4.4.1 (e)) | 1 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Speedometer not fitted speedo covered (7.8 (a)) | 1 |
Brake hose excessively deteriorated | 1 |
Offside Front Upper Torque/reaction arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Rear Rear fog lamp not working |1.3.2b| | 1 |
Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Centre Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Rear front brake binding |3.7.B.1| | 1 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
Offside Rear Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
Nearside Front Lower Shock absorbers likely to become detached (5.3.2 (a) (ii)) | 1 |
Offside Front Lower Shock absorbers likely to become detached (5.3.2 (a) (ii)) | 1 |
Nearside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Front (6.1.1 (c) (i)) | 1 |
Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Offside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Offside Outer Body panel corroded and likely to cause injury central (6.2.1 (a) (i)) | 1 |
Offside Rear Outer Body panel corroded and likely to cause injury corner (6.2.1 (a) (i)) | 1 |
Offside Rear Lower Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Nearside Front Outer Body panel corroded and likely to cause injury (6.2.1 (a) (i)) | 1 |
Nearside Front Lower Suspension arm pin or bush excessively worn Front and rear (5.3.4 (a) (i)) | 1 |
Offside Front Lower Suspension arm pin or bush excessively worn Front and rear (5.3.4 (a) (i)) | 1 |
Emissions not tested |7.0| | 1 |
Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Steering locking device missing |2.2.C.1g| | 1 |
Nearside Front An item not tested |Manual| | 1 |
Nearside Rear An item not tested |Manual| | 1 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Fuel tank leaking |7.2.3| | 1 |
Nearside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Offside Rear Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Offside Steering rack gaiter split |2.2.D.2d| | 1 |
Offside Headlamp insecure |1.7.3| | 1 |
Nearside Front Torsion bar excessive play at an end fixing |2.4.E.2| | 1 |
Nearside Obligatory mirror insecure |8.1.1| | 1 |
Battery insecure |1.9.1| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded front of spring |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded rear of spring |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded rear of spring |2.4.A.3| | 1 |
Offside Front Steering rack gaiter insecure |2.2.D.2d| | 1 |
Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Nearside Rear Brake pipe leaking |3.6.A.1| | 1 |
Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
Offside Inner Ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
Offside Headlamp aim not tested |1.8.A.1c| | 1 |
Nearside Side repeater incomplete |1.5.A1b| | 1 |
Offside Side repeater incomplete |1.5.A1b| | 1 |
Offside Headlamp not working on main beam |1.7.5a| | 1 |
Brake pedal anti-slip provision missing |3.3.A.1b| | 1 |
Steering rack damaged and unserviceable |2.2.C.1d| | 1 |
Offside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Front Upper Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Front Lower Suspension arm synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
Nearside Front Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 1 |
Offside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
Rear wheel bearing has excessive play |2.6.2| | 1 |
Offside Front Obligatory mirror seriously deteriorated, affecting the rear view |8.1.2a| | 1 |
Nearside Front Ball joint has excessive play |2.2.B.1f| | 1 |
Brake load sensing valve linkage seized |3.6.E.3| | 1 |
Offside Outer Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |