Most common failures | No# failures |
---|
Headlamp aim out of alignment | 15 |
Registration plate lamp issues | 9 |
Offside Headlamp aim beam image kick up to the offside |1.8| | 8 |
Nearside Headlamp aim beam image kick up to the offside |1.8| | 7 |
Rear parking brake recording little or no effort | 6 |
Offside Rear fog lamp not working |1.3.2b| | 6 |
Windscreen wiper does not clear the windscreen effectively | 6 |
Brake pipe excessively corroded | 6 |
Parking brake: efficiency below requirements |3.7.B.7| | 5 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
Battery insecure |1.9.1| | 4 |
Brakes imbalanced across an axle | 4 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 3 |
Nearside Stop lamp not working |1.2.1b| | 3 |
Nearside Front Seat belt retracting mechanism defective |5.2.5b| | 3 |
Rear fog lamp not working |1.3.2b| | 2 |
Offside Stop lamp not working |1.2.1b| | 2 |
Offside Front Direction indicator not working |1.4.A.2c| | 2 |
Registration plate issues | 2 |
Brake load sensing valve linkage defective and function impaired Mounting clamp missing (1.1.17 (a)) | 2 |
Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
Offside Rear Axle swivel pins and bushes swivel pin and/or bush excessively worn seized (5.1.2 (b) (i)) | 2 |
Windscreen washer not working | 2 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Service brake: efficiency below requirements |3.7.B.7| | 2 |
Offside Headlamp not working on dipped beam |1.7.5a| | 2 |
Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Rear Exhaust mounting missing |7.1.1b| | 2 |
Emissions not tested |7.0| | 2 |
Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
Rear brake application uneven | 2 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 2 |
Offside Front brake disc excessively pitted |3.5.1h| | 2 |
Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Brake load sensing valve has been disconnected and was fitted as standard |3.6.E.2| | 2 |
Offside Front drive shaft support bearing excessively worn |2.5.C.2c| | 2 |
Offside Headlamp insecure |1.7.3| | 2 |
Horn not a continuous or uniform sound |1.6.2e| | 1 |
Nearside Upper Front position lamp|s| not working |1.1.A.3b| | 1 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Brake hose has insufficient room to move | 1 |
Nearside Rear Upper Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Nearside Upper Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Seat belt insecurely fixed to the seat |5.2.1a| | 1 |
Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Headlamp aim beam image kick up to the offside |1.6.B1| | 1 |
Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
Rear brake binding | 1 |
Hazard warning switch faulty |1.4.B.1d| | 1 |
Front constant velocity joint is insecure 1x bolt missing on drive shaft |2.5.C.1b| | 1 |
Emissions not tested fuel level low |7.3.A.1| | 1 |
Offside Rear Radius arm severely distorted |2.4.G.1| | 1 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
Offside rear brake recording little or no effort |3.7.B.5a| | 1 |
Offside Rear Bonded suspension unit bonding failed and part of unit is likely to become displaced |2.4.F.2| | 1 |
Offside Rear Bonded suspension unit deteriorated and cannot function as intended |2.4.F.3| | 1 |
Windscreen wiper not operating over a large enough area to give an adequate view not working at all |8.2.1c| | 1 |
Nearside Inner Front constant velocity joint is insecure |2.5.C.1b| | 1 |
Nearside Front drive shaft coupling is insecure securing bolts missing |2.5.C.1c| | 1 |
engine mounting bracket insecure and likely to fail gearbox bolts loose |6.1.D.1b| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded inner wing under bonnet |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing under bonnet |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Nearside Rear Axle swivel pins and bushes swivel pin and/or bush excessively worn Excessive movement (5.1.2 (b) (i)) | 1 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Rear All position lamps adversely affected by the operation of another lamp all affected by brake lights (4.2.3 (c)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength top mount (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength top mount (5.3.6 (a) (i)) | 1 |
Nearside Rear Axle swivel pins and bushes swivel pin and/or bush excessively worn excessive movement (5.1.2 (b) (i)) | 1 |
Nearside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
Battery insecure and likely to fall from carrier |4.13 |a| |ii|| | 1 |
Fuel cap/sealing device ineffective |6.1.3 |b| |i|| | 1 |
Nearside Front constant velocity joint is insecure |2.5.C.1b| | 1 |
Offside Front constant velocity joint is insecure |2.5.C.1b| | 1 |
Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
Nearside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
Offside Rear position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 1 |
Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
Offside Rear Hazard warning lamps inoperative |1.4.B.1b| | 1 |
Offside Passenger`s seat insecure |6.2.A.1| | 1 |
Nearside Rear wheel cylinder leaking |3.6.A.1| | 1 |
Centre Exhaust has a part missing |7.1.1a| | 1 |
Offside Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Fuel cap/sealing device missing |7.2.4a| | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Nearside Front Suspension component ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Offside Front Suspension component ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Nearside Rear Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Rear Exhaust has a part missing |7.1.1a| | 1 |
Front Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
Nearside rear brakes release unevenly |3.7.B.4| | 1 |
Offside rear brakes release unevenly |3.7.B.4| | 1 |
Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
Front Headlamps matched pair are incorrectly positioned |1.7.3| | 1 |
Rear Lower Exhaust system not adequately supported |7.1.1| | 1 |
Rear Rear fog lamp not working |1.3.2b| | 1 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Offside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Service brake excessively fluctuating |1.2.1 |e|| | 1 |
Nearside Front Service brake excessively binding |1.2.1 |f|| | 1 |
Offside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 1 |
Nearside Rear Parking brake inoperative on one side |1.4.1 |a|| | 1 |
Offside Rear Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
Driver`s door cannot be opened from inside the vehicle |6.2.3 |a|| | 1 |
Nearside Front Brake disc significantly and obviously worn |1.1.14 |a| |i|| | 1 |
Exhaust system insecure rubbers missing |6.1.2 |a|| | 1 |
Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 1 |
Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Exhaust system insecure no mountings fouling steering (6.1.2 (a)) | 1 |
Rear Brake load sensing valve linkage defective and function impaired (1.1.17 (a)) | 1 |
Boot lid insecure n/s mounting bracket missing o/s/lock missing (6.2.1 (a) (i)) | 1 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Rear Parking brake inoperative on one side Very little effort (1.4.1 (a)) | 1 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
Offside Front Brake pipe leaking |3.6.A.1| | 1 |
Offside Front Front constant velocity joint is insecure |2.5.C.1b| | 1 |
Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
Offside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
Brake performance not tested |3.7.A.1| | 1 |
Headlamp aim beam image kick up to the offside |1.8| | 1 |
Offside Rear Air suspension unit displaced |2.4.D.1a| | 1 |
front brake juddering severely |3.7.A.2b| | 1 |
Nearside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
Nearside Rear Brake pipe excessively damaged |3.6.B.2c| | 1 |
Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Offside rear brake juddering severely |3.7.A.5b| | 1 |
Offside Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Nearside Front Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Rear Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Rear Stop lamp emits other than a steady red light |1.2.1e| | 1 |
Offside Rear Stop lamp emits other than a steady red light |1.2.1e| | 1 |
Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
Horn not working (7.7 (a)) | 1 |
Direction indicator not working all (4.4.1 (a) (ii)) | 1 |
Hazard warning lamps inoperative (4.4.1 (e)) | 1 |
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Front Exhaust mounting missing |7.1.1b| | 1 |
Brake hose excessively deteriorated | 1 |
Offside Rear Service brake excessively binding unable to rotate wheel and check wheel bearing (1.2.1 (f)) | 1 |
Nearside Rear Suspension unit damaged or deteriorated and function affected air bag top locating bracket bent (5.3.5 (b) (i)) | 1 |
Offside Front Direction indicator likely to become detached (4.4.1 (c) (ii)) | 1 |
Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Nearside Rear Shock absorber - all missing when fitted as standard |2.7.1a| | 1 |
Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Service brake: efficiency below requirements |3.7.D.4| | 1 |
Offside Rear Statutory seat belt missing |5.1.1| | 1 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
Offside Rear Outer Rear position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Headlamp not working on main beam |1.7.5a| | 1 |
Centre Exhaust mounting missing |7.1.1b| | 1 |
Power steering component|s| leaking |2.3.3b| | 1 |
Offside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Parking brake lever has no reserve travel |3.1.6b| | 1 |
Offside Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
Parking brake recording little or no effort |3.7.D.3a| | 1 |
Parking brake: efficiency below requirements |3.7.D.4| | 1 |
Offside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 1 |
Nearside Headlamp insecure |1.7.3| | 1 |
Nearside Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |