| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 77 |
| Windscreen wiper does not clear the windscreen effectively | 45 |
| Headlamp aim out of alignment | 30 |
| Registration plate lamp issues | 21 |
| Horn not working |1.6.2a| | 18 |
| Brakes imbalanced across an axle | 13 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 9 |
| Nearside Stop lamp not working |1.2.1b| | 8 |
| Rear brake binding | 8 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 7 |
| Registration plate issues | 7 |
| Horn not working |7.7 |a| |ii|| | 7 |
| Offside Rear fog lamp not working |1.3.2b| | 7 |
| Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 6 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 6 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 6 |
| Horn not working (7.7 (a) (ii)) | 6 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 5 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 5 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 5 |
| Windscreen washer not working | 5 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Front brake excessively fluctuating | 4 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 4 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 4 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 4 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 3 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Front brake disc in such a condition that it is seriously weakened | 3 |
| Battery insecure |1.9.1| | 3 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 3 |
| Centre Exhaust system not adequately supported |7.1.1| | 3 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 3 |
| Centre Exhaust mounting missing |7.1.1b| | 3 |
| Exhaust system not adequately supported |7.1.1| | 3 |
| Windscreen has damage | 3 |
| Parking brake: efficiency below requirements |3.7.B.7| | 3 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 3 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 3 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 3 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 3 |
| Brake hose excessively deteriorated | 3 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 3 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Rear Stop lamp not working |1.2.1b| | 2 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Emissions not tested |7.0| | 2 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Rear brake application uneven | 2 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 2 |
| Rear fog lamp not working |1.3.2b| | 2 |
| Rear fog lamp tell tale not working |1.3.1b| | 2 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 2 |
| Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 2 |
| Offside Side repeater not working |1.4.A.2c| | 2 |
| Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Stop lamp not working |1.2.1b| | 2 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Steering lock fails to engage |2.1.4b| | 2 |
| Horn sound not in accordance with requirements (7.7 (c)) | 2 |
| Emissions not tested |7.3.A.1| | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Nearside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Nearside Rear Stop lamp not working |1.2.1b| | 2 |
| Nearside Front Wheel bearing has excessive play |5.1.3 |a| |i|| | 2 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 2 |
| Offside Front Shock absorbers has a serious fluid leak | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength At rear inner wheel arch, within 300mm of nearside spring rear hanger and upper shock absorber mount (5.3.6 (a) (i)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength At offside inner wheel arch, within 300mm of spring rear hanger and upper shock absorber mount (5.3.6 (a) (i)) | 2 |
| Nearside Rear Seat belt buckle missing At seatbelt latch (7.1.2 (d)) | 2 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Front Direction indicators incorrect colour |1.4.A.2f| | 2 |
| Offside Front Direction indicators incorrect colour |1.4.A.2f| | 2 |
| Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Centre Rear Stop lamp not working |1.2.1b| | 2 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Nearside Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Emissions not tested lambda too high (8.2.1.2 (d)) | 1 |
| Exhaust has a major leak of exhaust gases in front section (6.1.2 (a)) | 1 |
| Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4) | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3) | 1 |
| Horn not working (1.6.2a) | 1 |
| Offside Front Direction indicator incorrect colour (1.4.A.2f) | 1 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside front brake juddering severely |3.7.A.2b| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced crossmember (6.1.1 (c) (i)) | 1 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Offside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Brake hose damaged | 1 |
| Nearside Front Road wheel bead rim badly distorted |4.2.A.1a| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Front brake disc excessively pitted |3.5.1h| | 1 |
| Brake pedal anti-slip provision worn smooth |3.3.A.1b| | 1 |
| Nearside Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Centre Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Nearside Front Braking system leaking |3.6.A.1| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front Headlamp aim not tested |1.8.A.1c| | 1 |
| Offside Front Headlamp aim not tested |1.8.A.1c| | 1 |
| Fuel pipe leaking Engine bay |6.1.3 |b| |i|| | 1 |
| Windscreen wiper not working both front (3.4 (a)) | 1 |
| Emissions not tested readings off scale |7.3.A.1| | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Exhaust has a major leak of exhaust gases manifold |6.1.2 |a|| | 1 |
| Exhaust fumes entering cabin due to manifold leak |6.1.2 |b| |i|| | 1 |
| Exhaust mounting missing |7.1.1b| | 1 |
| Central Exhaust system not adequately supported rubber mounts missing |7.1.1| | 1 |
| Front Windscreen damaged and affecting the driver`s view of the road |3.2 |a| |ii|| | 1 |
| Offside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Inner wheel arch (5.3.6 (a) (ii)) | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded side step |2.4.A.3| | 1 |
| Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Offside Front Valve stem seriously damaged |4.1.D.1e| | 1 |
| Nearside Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Inner Front Power steering pipe|s| or hose|s| excessively corroded |2.3.2| | 1 |
| Offside Inner Front Power steering pipe|s| or hose|s| excessively corroded |2.3.2| | 1 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower front edge of suspension turret corroded and holed. (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked in yellow |5.3.6 |a| |i|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked in yellow |5.3.6 |a| |i|| | 1 |
| Offside Front Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked in yellow (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked in yellow (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength marked in yellow (5.3.6 (a) (i)) | 1 |
| Central Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength along cross member ( marked in yellow ) (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Brake prescribed area is excessively corroded (1.1.21 (e) (i)) | 1 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outter sills |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner and outter |7.1.1 |a| |i|| | 1 |
| Nearside Front Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength and offside cross member |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded Rear leaf spring anchor, sill area |2.4.A.3| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded Rear leaf spring anchor, sill area |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded Rear leaf spring anchor, sill area |2.4.A.3| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is inadequately repaired Rear leaf spring anchor, sill area |2.4.A.3| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is inadequately repaired front leaf spring anchor, sill area |2.4.A.3| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded Front leaf spring anchor, sill area |2.4.A.3| | 1 |
| Nearside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Direction indicator incorrect colour |4.4.3 |a|| | 1 |
| Offside Front Direction indicator incorrect colour |4.4.3 |a|| | 1 |
| Nearside Front Upper Position lamp not working |4.2.1 |a|| | 1 |
| Nearside Rear Upper Position lamp not working |4.2.1 |a|| | 1 |
| Offside Stop lamp|s| remains on when the brakes are released incorrect bulb |4.3.2 |a| |iii|| | 1 |
| Nearside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt ball joint |5.3.4 |b| |ii|| | 1 |
| Offside Front Lower Suspension component ball joint dust cover no longer prevents the ingress of dirt ball joint |5.3.4 |b| |ii|| | 1 |
| Nearside Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
| Emissions not tested very high first reading (8.2.1.2 (d)) | 1 |
| Nearside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Central Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Front Upper Outline marker lamp not working |4.2.1 |a|| | 1 |
| Nearside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Battery insecure and likely to fall from carrier |4.13 |a| |ii|| | 1 |
| Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Nearside Front Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring mounting area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point area (5.3.6 (a) (i)) | 1 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Power steering pipe/hose leaking Both metal power steering pipes on rack corroded and leaking (2.1.5 (a)) | 1 |
| Offside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively damaged significantly reducing structural strength strut mounting / inner wing (5.3.6 (a) (i)) | 1 |
| Suspension arm ball joint likely to become detached locking device not on thread (5.3.4 (a) (ii)) | 1 |
| Brake cable damaged corroded (1.1.15 (a)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced out rigger (6.1.1 (c) (i)) | 1 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Nearside Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt insecure |6.1.7 |g| |ii|| | 1 |
| Brake performance not tested |3.7.A.1| | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Chassis (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Wing/chassis (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired inner wing |2.4.A.3| | 1 |
| Front Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Rear Brake load sensing valve seized |3.6.E.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded inner arch area |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded jacking point |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded upper inner arch area |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded step area |2.4.A.3| | 1 |
| Offside Steering rack gaiter split |2.2.D.2d| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |7.1.4| | 1 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner chassis |2.4.A.3| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Nearside Rear Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Rear position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Nearside Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Nearside Front Windscreen wiper not working (3.4 (a)) | 1 |
| Offside Front Position lamp not working |4.2.1 |a|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing, subframe mounting area. |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength rear valance area |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength rear valance area |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength front spring eye |5.3.6 |a| |i|| | 1 |
| Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Horn not loud enough to be heard by another road user |1.6.2b| | 1 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength strenthner bar (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases middle section (6.1.2 (a)) | 1 |
| Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Outer Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
| Offside Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
| Nearside Rear Brake valve insecurely mounted |3.6.A.2a| | 1 |
| Nearside Inner Rear Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Lower Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings inner sill holed |6.1.B.2| | 1 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassy leg (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced step (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced welds (6.1.1 (c) (i)) | 1 |
| Nearside Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings FLOOR HOLED |6.1.B.2| | 1 |
| Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings OUTRIGGER HOLED |6.1.B.2| | 1 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing/chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired inner wing/chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member at rear spring mounting (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength leaf spring hanger (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength leaf spring hanger (5.3.6 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Vehicle structure is deformed and structural rigidity is significantly reduced |6.1.1 |a| |i|| | 1 |
| Rear Vehicle structure is fractured and structural rigidity is significantly reduced crossmember |6.1.1 |a| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis |6.1.1 |c| |i|| | 1 |
| Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Rear Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
| Nearside Rear Shock absorbers insecurely attached |5.3.2 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired |5.3.6 |a| |i|| | 1 |
| Steering column flexible coupling is excessively deteriorated |2.2.2 |c|| | 1 |
| Nearside Front Track rod end ball joint has excessive play |2.1.3 |b| |i|| | 1 |
| Offside Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen |3.5 |a|| | 1 |
| Nearside Front Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction |3.1 |a| |ii|| | 1 |
| Offside Front Driver`s view of the road through the swept area of the windscreen materially affected by an obstruction wipper park |3.1 |a| |ii|| | 1 |
| Front Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced |6.1.1 |b| |ii|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced At middle side door( underside) where marked (7.1.1 (a) (i)) | 1 |
| Nearside Subframe mounting prescribed area excessively corroded significantly reducing structural strength At wheel arch within 300mm of subframe mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired Within 300mm of rear spring rear hanger (5.3.6 (a) (i)) | 1 |
| Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
| Offside Rear Statutory seat belt missing |5.1.1| | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Driver`s seat insecure |6.2.A.1| | 1 |
| Front passenger seat insecure |6.2.3| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill holed due to corrosion within 30cm of rear suspension mtg point |5.3.6 |a| |i|| | 1 |
| Offside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheelarch |5.3.6 |a| |i|| | 1 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength step |5.3.6 |a| |i|| | 1 |
| Offside Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength step |5.3.6 |a| |i|| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Horn not working unplugged (7.7 (a)) | 1 |
| Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill area |6.1.B.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill area |6.1.B.2| | 1 |
| Nearside Front Windscreen wiper blade missing |8.2.2| | 1 |
| Rear Mechanical brake component has restricted free movement | 1 |
| Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Front Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Upper Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
| Offside Rear Lower Suspension component mounting prescribed area is inadequately repaired lower inner sill |2.4.A.3| | 1 |
| Central Rear Suspension component mounting prescribed area is excessively corroded chassis cross member both sides |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired jacking point |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired rear outer sills |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is inadequately repaired rear outer sills |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded chassis out rigger |2.4.A.3| | 1 |
| Central Rear Suspension component mounting prescribed area is excessively corroded cross member |2.4.A.3| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded lower sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired wheel arch |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded jacking point |2.4.A.3| | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded behind bumper end caps |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded behind bumper end caps |2.4.A.3| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded leaf spring mount |2.4.A.3| | 1 |
| Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper chassis |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x member in various places |5.3.6 |a| |i|| | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength middle inner sill |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 1 |
| Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill front of leaf spring (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill rear of leaf spring (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill at front of leaf spring x2 (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill at rear of leaf spring x2 (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x member (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wing x2 (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Door step (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Door step (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring hanger (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x-member (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x-member (5.3.6 (a) (i)) | 1 |
| Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x-member all along (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension turret (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension turret (5.3.6 (a) (i)) | 1 |
| Central Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Nearside Front Inner Brake prescribed area is excessively corroded wheel arch (1.1.21 (e) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Power steering pipe/hose excessively corroded x2 (2.1.5 (g) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting by eng mount (6.2.2 (d) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength by ls mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Position lamp not working side light (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength by ls mount (5.3.6 (a) (i)) | 1 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Front Shock absorbers insecurely attached 1 bolt loose (5.3.2 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front subframe offside rear mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Body component insecure (6.2.1 (a) (i)) | 1 |
| Offside Front Service brake excessively binding recheck wheel bearing (1.2.1 (f)) | 1 |
| Emissions not tested |8.2.1.2 |d|| | 1 |
| Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Offside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Emissions not tested (8.2.1.2 (d)) | 1 |
| Offside Front Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded Inner sill to doorstep |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded Inner sill |2.4.A.3| | 1 |
| Brake pipe leaking |3.6.A.1| | 1 |
| Front brake application uneven | 1 |
| Offside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Nearside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Offside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Battery insecure and likely to cause a short circuit |4.13 |a| |ii|| | 1 |
| Nearside Headlamp levelling device inoperative |4.1.5 |a|| | 1 |
| Offside Headlamp levelling device inoperative |4.1.5 |a|| | 1 |
| Exhaust has a major leak of exhaust gases Centre section silencer |6.1.2 |a|| | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Exhaust system insecure Rubber mountings broken (6.1.2 (a)) | 1 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Central Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Nearside Inner Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Upper Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Dipswitch does not operate immediately when selected on main beam |4.1.3 |b|| | 1 |
| Nearside Outer Upper Front position lamp|s| not working |1.1.A.3b| | 1 |
| Horn not working (7.7 (a)) | 1 |
| Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 1 |
| Nearside Outer Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Front Service brake imbalanced across an axle (1.2.1 (b) (i)) | 1 |
| Offside Rear Upper Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength within 30 cm of leaf spring mountings |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength within 30cm of leaf spring mountains |5.3.6 |a| |i|| | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking points (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking points x 2 patches (5.3.6 (a) (i)) | 1 |
| Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |